Question about 2006 Mitsubishi Outlander

Open Question

2006 outlander low beam light replacement can't get wire retainer cluip back in place; red wire now broken off;after I get it back together is there an easy way to replace the low beam h-1 bulb ?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: trying to replace a front headlight bulb on 2001 acura 3.2 TL

Look for the end of the wire retainer clip. Unhook it and lift it up. Remember not to touch the bulb. But if you do, just clean it with a bit of alcohol.

btw - Here's a bit of info from a previous post of mine...
The low beams consist of three parts. The bulb, inverter/ballast and the ignitor. The bulbs usually start to loose their color long before they burn out. The inverters/ballasts either go out after a while or take a while to start up.

Before you spend money on a new bulb, try swapping it with the one on the other side. You'll need a security torx screwdriver to get the covers off of the back of the lights. Don't touch the glass bulbs. If you do, just clean them with a bit of alcohol.

If the problem stays on that side, try swapping the ignitors. They're mounted inside the black covers.

If the problem is still on that side you've got a bad inverter. They're mounted on the bottom of the headlight assembly. You'll need to remove the front bumper and remove the headlight assembly to get to it. (I recommend you take pictures as you remove things so can put them back together correctly.)

Posted on Jan 05, 2009

blueextc3221
  • 15935 Answers

SOURCE: How do you replace the headlight bulb in 2003 Mitsu Outlander?

if you are removing the power clip, grab the recepticle it was plugged in to (look at your new bulb as a reference) and twist counterclockwise. The entire bulb assembly will come out, and replace with the new assembly.

Posted on Jan 06, 2009

  • 1 Answer

SOURCE: 2006 Trailblazer Headlight Replacement

There are not two rods, there are two clips one under fender weild and one right above the light on top of the cover. Pull up on these two clips and pull the light forward a couple of inches and remove the dust cover. You have to take the air filter cover off to be able to reach in and replace the light. It took me about 10 min to figure these out but hope it helps out.

Posted on Jan 14, 2009

johnny5846
  • 379 Answers

SOURCE: replacing low beam head light on nissan altima

your welcome , glad to have assisted you

J5

Posted on Jan 21, 2009

countrysi248
  • 443 Answers

SOURCE: Difficulty changing low-beam headlight

they have a little clip over device you look close and you will see how it works just pull the clip device back and pull it off .. Jerry

Posted on Feb 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Volkswagon Beetle, drivers side headlight, high beam not working


Instructions
    • Turn the headlight switch on and inspect the headlights. Make sure to check both low- and high-beam lights, and then note the position of the bulb in the headlight assembly. Low-beams are in the top cavity of the assembly and high-beams are in the lower cavity.
    • 2Turn off the headlight switch and then remove the keys from the ignition.
    • 3
    • Open the hood and locate the seam to the headlight assembly and the side fender. Locate the headlight assembly release lever and push in on it slightly to unlock it and then pull it all the way up until it stops.
    • 4Place a blanket or pillow on the ground in front of the headlight assembly. Push the assembly outward from behind with one hand while being ready to catch the assembly with the other. The New Beetles use an adhesive sealant to protect the back of the headlights from exposure to moisture, so you'll have to give the assembly a push from behind.
    • 5Pull the wire harness plugs off from both the high- and low-beam blades of the respective bulbs.
    • 6Place the assembly on the blanket or pillow. Release the wire clip to the faulty headlight and then remove the headlight bulb.
    • 7Open the package of the new H1 bulb replacement without touching the glass portion of the bulb with your bare skin. Oils in human skin will damage the bulb. Handle it only by the metal base of the bulb insert.
    • 8Insert the new bulb in the appropriate headlight-assembly cavity and reattach the bulb retaining clip to lock the bulb in place.
    • 9Lift the assembly up and plug the wire harness plugs back into the respective blades of the bulbs.
    • 10Push the headlight assembly into its cavity, but before locking it in place, check the lights by turning on the headlight switch.

Sep 17, 2012 | 2006 Volkswagen New Beetle

5 Answers

I have a 2006 PT Cruiser that the left low beam headlamp bulb blew out; I purchased a replacement bulb and replaced it, the bulb would not light, so I then swapped the bulb from the right side with the...


This is a legitimate problem with light bulbs on Chrysler products.. The best resolution is to purchase a used module from a salvage yard to replace yours which is very much cheaper to do

Mar 04, 2011 | 2006 Chrysler PT Cruiser

1 Answer

Need to replace low beam headlight bulb


Hello,

it's easier to change the light bulbs in this car than in a lot of other vehicles. The 2008 pontiac Grand Prix uses separate bulbs for low beams and high beams. The low beams are located on the outer edge of the headlight assemblies while the high beams are located on the inner edge of the assemblies.
To replace the low beam of the headlight bulb You will be in need of these instruments(Soft blanket or towel, Latex gloves, 9006 replacement headlight (low beam)), please follow the steps below:
  1. Open the hood to the 2008 Pontiac Grand Prix after making sure the headlight switch is in the off position, and the keys are not in the ignition.
  2. Approach the headlight assembly with the spent headlight in it, and locate the retaining bracket (white) holding the assembly to the frame rail of the Grand Prix.
  3. Lift the retaining bracket up about a quarter of an inch in order to align the notches of the bracket to the riveted tabs on the frame.
  4. Pull the assembly forward away from the front of the car starting with the inner corner of the assembly toward the grill. Keep in mind the wire harness connection is still attached to the assembly, so only pull it far enough to reach behind and disconnect the plug located at the bottom of the assembly.
  5. Place the headlight and bulbs assembly lens down onto a soft towel or blanket.
  6. Disconnect the respective low beam or high beam wire harness.
  7. Turn the plastic base of the headlight counterclockwise a quarter turn to align the retaining tabs with the release notches. Remove the headlight from the headlight assembly.
  8. Put on latex gloves before handling the replacement low beam or high beam headlight. Oil from skin will compromise the life of the headlights if it contacts the glass bulb.
  9. Insert the new bulb into the assembly by aligning the retaining notches to the release tabs, and then turn the base of the headlight 1/4 clockwise to lock it into the headlight assembly. Reconnect the harness to the headlight.
  10. Bring the assembly back to the Grand Prix and reconnect the main wire harness at the bottom of the assembly.
  11. Align the guide pins at the back of the assembly to the locating holes in the front frame rail starting with the outer guide pin first and the inner (toward the grill) guide pin last. Lift the assembly upward while pushing back on the lens to push down on the retaining bracket.
  12. Place the key in the ignition and turn the key to accessory power.
Hope this helped. Thank You for using FixYa!!!

Jan 20, 2011 | 2008 Pontiac Grand Prix

1 Answer

How do i remove bulb from socket for day time running light on 2002 avalanche


dak408_133.gif
  1. Open the hood.
  2. Remove the park/turn signal lamp assembly.
  3. Remove the headlamp retainer pins.
  4. Pull out the headlamp assembly in order to access the electrical connector.
  5. Disconnect the electrical connector.
  6. Remove the bulb from the headlamp assembly by twisting the bulb counterclockwise.
INSTALLATION PROCEDURE

IMPORTANT:
  • Replace a high beam bulb with another high beam bulb. The high beam bulb has a red gasket.
  • Replace a low beam bulb with another low beam bulb. The low beam bulb has a gray tip and a yellow gasket at the base.
  1. Install the new bulb to the headlamp assembly by twisting the bulb clockwise in order to lock in place.
  2. Connect the electrical connector to the bulb.
  3. Install the headlamp assembly.
  4. Install the headlamp retainer pins.
  5. Rotate and lock the pins in place.
  6. Install the park/turn signal lamp assembly.
  7. Inspect the operation.

Dec 11, 2010 | 2002 Chevrolet Avalanche

1 Answer

Change low beam headlight


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Nov 06, 2010 | 2002 Jaguar X-Type

1 Answer

How do you replace xeon headlight low beam bulb


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Nov 05, 2010 | 2005 Volvo S80

2 Answers

How do I replace a left hand side low beam light on a Subaru Tribeca 2008


Inspect/Replace There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
f19-22.jpg Comparing the old and ther replacement headlamps. To Replace:
  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Oct 28, 2010 | 2008 Subaru B9 Tribeca

1 Answer

My brights quit working. My headlights work fine on my 2006 Chevy Equinox


Most of the time I find that both headlight bulbs are burned out. Remove the headlamp, open the hood and remove the retainers that hold the front grill/bumper cover to the upper radiator support. The gently pull out on the front bumper cover that goes over the headlamp to release the retainer and cover retainer with tape to avoid scratching the headlamp lens. remove the 3 bolts that hold the headlamp in place 2 at the top and one down at the bottom of the headlamp on the inboard side. Pull out on the outboard bottom part of the headlamp to release the retainer. Disconnect the headlamp bulb ck for power and ground at the headlight bulb connector. Use a test light and ck the red and white wire voltage and the d blue and pnk wires for ground. The high beam is the pink wire.So connect your test light from the pink wire to the red and white wire and turn on the high beam headlights your test light should light if it does then the bulb is burned out.

Feb 15, 2010 | 2007 Chevrolet Equinox LS New Cars

2 Answers

How do I change the lowbeam headlight on my 2003 Chev Trail Blaze


hi..Should be a Halogen bulb High-low beam combo maybe.
As you are looking down at the back of the headlight assembly
gently push down on the clip that holds the wiring harness to the
bulb. Now rotate the bulb counter clock wise (left) and then remove
it. Reverse process to install.
check it out..
thank u..
rate me..

Mar 10, 2009 | 2006 Chevrolet Trailblazer Ext

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...