Question about 1983 Jeep CJ7

Open Question

Why would my parking brake strut be bent? - 1983 Jeep CJ7

Posted by on

  • Richard Scordino Sep 15, 2010

    Impossible to answer that. Over the past twenty years or so, any number of things could have happened to it! Important part is to fix it if it's damaged badly enough for it not to work.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear brakes


Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.
bj6c017a.gif
3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.
bj6c017b.gif
5.Remove adjuster spring from adjust lever and brake shoe.
bj6c017c.gif
6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.
bj6c017d.gif
7.Remove the strut spring and the lower retracting spring from the brake shoe.
bj6c017e.gif
8.Remove the upper return spring from the brake shoe.
bj6c017f.gif
9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.
bj6c017g.gif
11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.
bj6c017h.gif
12.Remove the trailing brake shoe from the rear parking cable.
bj6c017i.gif
13.Remove parking pivot lever from the leading brake shoe.
bj6c017j.gif
Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.
bj6c017n.gif
2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.
bj6c017o.gif
7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.
bj6c017d.gif
9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.
bj6c017q.gif
11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.
bj6c017k.gif
4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)
bj6c017l.gif
5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.
bj6c017m.gif

Aug 14, 2013 | 2002 Kia Sedona

1 Answer

I was in a parking g garage and turned Rolling over a curb with only my back passenger side wheel. Now we have noticed when you turn the van on a rattle noise as well as every now and then a scrapping...


not sure but maybe a shock or strut broke or bracket for shock or strut bent also check park brake assembly may be rubbing if van drives ok it should not be a problem to get home just keep an i on it good luck have a safe trip

Aug 12, 2013 | 1996 Jeep Grand Cherokee

1 Answer

How do you change rear drum brake shoes on a 1999 couger.


SECTION 206-02: Drum Brake 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 09/14/2001 Brake Shoes Removal
  1. Loosen the wheel nuts.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Remove the wheel.
  1. Release the brake shoe automatic adjuster.
    v1201041.jpg
  1. Remove the brake drum.
    1. Remove the retainers (if equipped).
    1. Remove the drum.
    v1201040.jpg
  1. Make sure that the hub flange is in the correct position as shown.
    v1201042.jpg
  1. Remove the hold down springs.
    m1201030.jpg
  1. Disconnect the parking brake cable.
    1. Lever the secondary shoe outwards.
    1. Disconnect the cable from the secondary shoe.
    v1201043.jpg
  1. Disconnect the shoes from the anchor block.
    1. Disconnect the shoes from the anchor block.
    1. Remove the lower return spring.
    v1201044.jpg
  1. ani_caut.gif CAUTION: Do not damage the wheel cylinder boots.
    Detach the shoes from the wheel cylinder.
    v1201045.jpg
  1. Hold the wheel cylinder pistons in place with a rubber band.
  1. Remove the upper return spring.
    v1201047.jpg
  1. Remove the primary shoe from the strut and brake shoe adjuster.
    1. Rotate the adjuster counterclockwise.
    1. Remove the primary shoe.
    v1201048.jpg
  1. ani_caut.gif CAUTION: Take care as the strut support spring is under tension.
    Detach the secondary shoe from the strut support.
    • Detach the strut from the shoe by levering the strut against the shoe.
    v1201049.jpg
  1. Remove the parking brake return spring.
    v1201050.jpg
Installation
NOTE: Install new shoes as axle sets.
  1. Clean, check and apply Silicon Dielectric Compound D742-18A331-A or equivalent meeting Ford specification ESA-M1C171-A to the backing plate contact points.
    v1201051.jpg
  1. Install the parking brake return spring.
    v1201050.jpg
  1. Install the secondary shoe to the strut and brake shoe adjuster.
    v1201052.jpg
  1. Install the primary shoe to the strut and brake shoe adjuster.
    1. Install the primary shoe.
    1. Rotate the adjuster fully clockwise.
    v1201053.jpg
  1. Install the upper return spring.
    v1201047.jpg
  1. Remove the rubber band holding the wheel cylinder pistons in place.
  1. ani_caut.gif CAUTION: Do not damage the wheel cylinder boots.
    Position the shoes to the wheel cylinder.
    v1201140.jpg
  1. Position the shoes to the anchor block.
    1. Install the lower return spring.
    1. Position the shoes to the anchor block.
    v1201141.jpg
  1. Install the hold down springs.
    v1201142.jpg
  1. Install the parking brake cable.
    1. Lever the secondary shoe outwards.
    1. Install the cable to the secondary shoe.
    v1201043.jpg
  1. Install the brake drum.
    1. Install the drum.
    1. Install the retainers (if equipped).
    v1201143.jpg
  1. Install the wheel.
    v1501127.jpg
  1. Operate the brake pedal to achieve automatic adjustment.

2010&c18=modelyear&c20=g167866&c35=wsm%2cbrake%20shoes%2csxu%2c206-02%2cremoval%20and%20installation&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 05, 2011 | 1999 Mercury Cougar

1 Answer

How to installing brake shoes on back ?


First you have to compress the parking brake cable spring and attach the parking brake lever.
Clean and lubricate the brake backing plate.
Use silicon Brake Caliper Grease and Dielectric Compound.
Then,
install the rear brake shoes and linings:
1) position the rear brake shoes and linings
2) position the parking brake lever
3) install the brake shoe hold-down spring pins and the brake shoe hold-down springs.

Install the parking brake strut
1. install the parkig brake link spring on the parking brake strut
2. install the parking brake strut
3. Install the brake shoe anchor ping guide plate.

Install the short brake shoe retracting spring
1. Place the brake shoe adjusting lever cable over the anchor pin, with crimped side in
2. Install the short brake shoe retracting spring

Note: Make sure the brake shoe adjusting lever cable is positioned in the cable guide groove

Install the long brake shoe retracting
1. install the cable guide
2. position the brake shoe adjusting lever cable in the cable guide groove
3. install the long brake shoe retracting spring

Note: to prevent incorrect installation, teh socket of each brake adjuster screw is stamped R or L

Assemble the brake adjuster screw assembly.
1. apply silicone brake caliper grease and dielectric compound
2. install the brake adjuster screw into the brake show adjusting screw nut to the end of the threads and then loosen one half turn
3. install the brake shoe adjusting screw socket on the brake shoe adjusting screw nut.

Install the brake adjuster screw assembly
1. Position the brake adjuster screw assembly
2. Install the brake shoe adjusting screw spring
3. Position the brake shoe adjusting lever cable
4. Position the adjusting lever return spring and the brake shoe adjusting lever
5. Hook the brake shoe adjusting lever cable to the brake shoe adjusting lever.

Test the operation of the automatic self-adjuster
1. Pull the brake shoe adjusting lever cable and check that the brake shoe adjusting lever rotates the brake shoe adjuster assembly
2. Release the brake shoe adjusting lever cable and check that the brake shoe adjusting lever advances to the next notch on the brake shoe adjusting screw nut.

Adjust the brakes.

Install the brake drum.

Thats it

Sep 10, 2010 | 1998 Ford Ranger SuperCab

1 Answer

I cant figure out how to assemble the back brake shoes and springs back together


Maybe to late for this but if you do one side at a time just look at the other side for how they go together. Also the short shoe goes toward the front long toward the back.
1. Clean and inspect individual brake components.
2. Lubricate anchor pin an brake show contact pads on support plate with high temperature grease or
Lubriplate. See Fig. 41 .
3. Lubricate adjuster screw socket, nut, button, and screw thread surfaces with grease or Lubriplate.
4. Install the parking brake cable to the parking brake lever.
5. Install parking brake lever to the secondary shoe and install retaining clip.
6. Install primary shoe on support plate. Secure shoe with new spring retainers and pin.
7. Install spring on parking brake strut and engage strut in primary.
8. Install secondary shoe on support plate. See Fig. 42 . Insert strut in shoe and guide shoe onto anchor pin.
Temporarily secure shoe with restraining pin.
9. Install anchor plate and adjuster cable eyelet on support plate anchor pin.
10. Install cable guide in secondary shoe and position cable in guide.
CAUTION: Be sure the adjuster screws are installed on the correct brake unit. The adjuster screws are marked
"L" (left) or "R" (right) for identification
11. Assemble adjuster screw. See Fig. 43 . Then install adjuster screw between the brake shoes.
12. Install adjuster lever and spring, and connect adjuster cable to lever.
13. Install secondary shoe retainers and spring.
14. Install shoe spring. Connect spring to secondary shoe first, then to primary shoe.
15. Verify adjuster operation. Pull adjuster cable upward, cable should lift and rotate star wheel. Be sure
adjuster lever properly engages star wheel teeth.
16. Adjust brake shoes. See REAR BRAKE SHOES under ADJUSTMENTS.
17. Install wheel and tire assembly. See TORQUE SPECIFICATIONS


8e04423.png

Jun 25, 2010 | 2001 Dodge Durango

1 Answer

Replace front wheel hub on 1992 Buick Park Avenue


1. Remover wheel
2. Remove brake caliper
3. Remover rotor
4. Remove 35mm Castle Nut
5. Remover 3 bolts behind strut assembly
6. UNclip any ABS sensor wires
7. Pull hub out of strut assembly but be careful not to pull CV joints out of axle

Mar 17, 2010 | 1992 Buick Park Avenue

1 Answer

I need a detailed discription for reassembling of the rear brakes.


1. Raise and support vehicle
2. remove wheel
3. check to be sure parking brake is released
4. remove brake drum
5. remove brake shoe hold-down springs
6. disconnect the parking brake cable
7. Remove the lower retracting spring.
8. disconnect shoes from the anchor block
9. disconnect the shoes from the wheel cylinder
10. Remove the upper retracting spring.
11. Remove the primary shoe from the strut and brake shoe adjuster.
A- Rotate the auto-adjuster counterclockwise.
B- Remove the primary shoe.
12. Disconnect the secondary shoe from the strut support.
13. Remove the parking brake return spring.
14 Reverse order to install

Nov 08, 2009 | 1998 Ford Contour

2 Answers

Having problem putting the rear brake drums on. Rear brake adjustment. Need a picture of the rear brake adjustment.


I don't have a picture for you, but the adjustment is done with the cam that is on the parking brake strut. just stick a small screwdriver between the ratchet teeth (it will slide back slightly under spring tension) it will then rotate on the strut assembly. if you rotate it one way it will make the strut longer (push the brake shoes out) and if you rotate it the other way it will make it shorter and bring the brake shoes in.

Oct 21, 2009 | 1998 Ford Contour

2 Answers

I'm doing the rear shoe brakes on a1994 Dodge Van B250 - 5.2 L engine. There is a pin on the bottom of the outside (back) shoe at the bottom. It holds the spring mechanism for the parking bake. I knocked...


im not sure of your the pin in which you speak but you can go to auto-zone and they have all you need for mishaps like that itll be in the section with the sockets and lubes atleast it is where im at.

Oct 03, 2009 | 1994 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...