Question about Mercedes-Benz E320

Open Question

How do I replace the rotor on a 1998 MBZ E320 rear wheel

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Pyrhyc
  • 2028 Answers

SOURCE: Replacing rear disk rotors on 2003 Mercedes E320

Generally when you remove the caliper assembly the rotor slides over the hub assembly. Since I have not done a brake job on this particular model, it may possibly be held in place by the hub nut. Remove the caliper assembly first in order to be sure. I could only find two diagrams for the brake assembly for the E320, neither one had the size of the nut or allan bolt. The easiest way to get the size is to measure from one flat area directly across to the other flat area this will give you the size for the socket and allan wrench needed. If in the US, keep in mind that this is in a metric measurement, so it will calculate to millimeters, which makes it much easier to measure than the American standard. Also, if you do have to remove the hub nuts, they will not have to be replaced unless you scar the threads or round the corners.

Posted on Jul 09, 2008

  • 1 Answer

SOURCE: Replacing the rear rotors on a 2003 E320

So this is what it takes to replace rear brake rotors on a 2003 Mercedes E320;
1) open the bonnet (hood) of the car and loosen/remove the cap off of the brake fluid resevior.
2) remove outer spring clamp from brake assembly (it clips in to the iner edge of the holes of the caliper).
3)using a 7 MM allen wrench, remove the brake caliper.
4) using 18 MM box wrench, remove the caliper housing assembly off of the wheel hub.
5) using a star wrench, unscrew the rotor locking screw from the rotor
6) squirt some liquid wrench on the rotor hub and knock the rotor with a hammer to work the liquid wrench in.
7) using the same hammer, knock the rotor off the hub.
8) using a metal file, lightly file old residue off of the hub and place the new rotor on the hub.
9) set the hub by screwing in the lug nuts and then screw in the hub locking screw using the star wrench, then remove the lug nuts.
10) reinstall the caliper housing assembly onto the wheel hub using the 18 MM box wrench.
11) push back the brake claiper piston to its home position and install the inner brake pad (the one with the snap clips)
12) insert the outer brake pad in the claper housing assembly.
13) slide on the caliper housing with the inner brake pad in place (over the outer brake pad) and screw in the caliper screw rods using the 7 MM allen wrench
14) on the right wheel brakes, DO NOT FORGET to slide in the brake sensor (the one with the black connector) and connect it to the connector on the caliper housing.
15) be sure to reinsert the spring clamp onto the outer brake assembly to set the assembly squarely onto the wheel (there should be no wiggle in the brake assembly after the spring clamps are installed).
16) finally mount the wheels.
17) you can bleed the brakes at this point to release any trapped air (which is unlikely) but be sure to pump the brakes after starting the car BUT BEFORE MOVING IT to re-preassurize the brake system before driving the car.
17) ONE WEEK LATER - recheck brake assembly to ensure all is okay and brake fluid.

This proposed solution is for a 2003 Mercedes Benz E320 and NOT a 2005 model as stated by the limited option selection provided by FIXYA.com when initially describing the problem.

Posted on Jul 10, 2008

ndguy2481
  • 251 Answers

SOURCE: How to reset brake pads message on dash of mbz E320 2005?

the only way is to take it to a dealer

Posted on Dec 04, 2008

  • 5 Answers

SOURCE: 1995 e320 mbz

ihave a diesel e320 won't start

Posted on Mar 12, 2009

  • 5 Answers

SOURCE: CHANGING THE HEADLIGHT ON AN E320 MBZ

It pretty straight forward of you open the hood and look at the back of the headlamp. You see a metal clip right where the wiring harness plugs into the back of the lamp. Just take a common screw driver and pop the clip out (be careful you don't pop the clip down into oblivion as it does tend to spring out with a bit of force.) The clip is held in place by two star headed screws. You do not need to mess with these, just pop the clip out from under the screw head. I assume it will say something to this effect when you buy the new bulb but be sure not to touch it directly with your skin as the oils in your skin will shorten the bulb's life considerably.

Posted on Oct 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do i to deal with the emergency brakes when replacing my rear brakesand rotors on my 2003 mercedes benz e320


no. As long as they are not locked on. They sit inside rotor and when you apply the brake the shoes for your e break push out to drag against inside of rotor. So the short answert is no you do not have to mess with them to replace disc brakes and rotors.

Nov 01, 2012 | Cars & Trucks

1 Answer

I changed all seats and door panels on my 2 cars mbz e320 1998 and 1999. now srs lights are on both of them. how can i reset the lights . thanks


as the seats have the sensors for the airbags,if you have not connected these up then the srs light will burn.if you have wired them up they will need to be reset at a dealer.

Aug 25, 2010 | Mercedes-Benz E320 Cars & Trucks

1 Answer

1998 Windstar: 1998 windstar replaced rotors but steering still s...


make sure the wheel hub surfaces are clean and free of rust both in front of and behind the rotors. also check that your rear brake adjusters are working correctly. also check wheel berring, balljoint and tierod ends for play. theres should be no play and berring should spin free of noise.

May 18, 2010 | 1998 Ford Windstar

1 Answer

How to install wheel bearing hub assemble (front)1998 on a ford escort


front or rear?

Assuming rear, on the brake drum:

Hub Removal
  1. If equipped, remove the brake drum (1126) ; refer to Section 206-02 . If equipped, remove the rear disc brake rotor (2C026) ; refer to Section 206-04 .
  1. Remove the wheel hub.
    1. Unstake the rear axle wheel hub retainer.
    1. Remove the rear axle wheel hub retainer and discard.
    1. Remove the wheel hub (1104).

Nov 05, 2009 | 1998 Ford Escort

1 Answer

CHANGING THE HEADLIGHT ON AN E320 MBZ


It pretty straight forward of you open the hood and look at the back of the headlamp. You see a metal clip right where the wiring harness plugs into the back of the lamp. Just take a common screw driver and pop the clip out (be careful you don't pop the clip down into oblivion as it does tend to spring out with a bit of force.) The clip is held in place by two star headed screws. You do not need to mess with these, just pop the clip out from under the screw head. I assume it will say something to this effect when you buy the new bulb but be sure not to touch it directly with your skin as the oils in your skin will shorten the bulb's life considerably.

Oct 01, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

CHANGING REAR BRAKE


For rear pads rear rotors changing procedure you need lift up car,secure front wheels, disconect rear wheels from rotors,(if you missing the bolts try drill it whith portable electric drill at first smal drill 3 mm diameter,then 10 mm diameter.)Disconect the hydraulics breake cylinders cearefully putt it on plate not tears the house.Change beake pads.Unscrew the rotor whith hexagonal wrench.Setup the hand bracke clearance.Putt agan the rotor on rear axis.Assembly the breake cylinders ,and wheel tighening 110 Hm.

Mar 07, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

1995 e320 mbz


ihave a diesel e320 won't start

Jul 28, 2008 | Mercedes-Benz E320 Cars & Trucks

1 Answer

Replacing the rear rotors on a 2003 E320


So this is what it takes to replace rear brake rotors on a 2003 Mercedes E320;
1) open the bonnet (hood) of the car and loosen/remove the cap off of the brake fluid resevior.
2) remove outer spring clamp from brake assembly (it clips in to the iner edge of the holes of the caliper).
3)using a 7 MM allen wrench, remove the brake caliper.
4) using 18 MM box wrench, remove the caliper housing assembly off of the wheel hub.
5) using a star wrench, unscrew the rotor locking screw from the rotor
6) squirt some liquid wrench on the rotor hub and knock the rotor with a hammer to work the liquid wrench in.
7) using the same hammer, knock the rotor off the hub.
8) using a metal file, lightly file old residue off of the hub and place the new rotor on the hub.
9) set the hub by screwing in the lug nuts and then screw in the hub locking screw using the star wrench, then remove the lug nuts.
10) reinstall the caliper housing assembly onto the wheel hub using the 18 MM box wrench.
11) push back the brake claiper piston to its home position and install the inner brake pad (the one with the snap clips)
12) insert the outer brake pad in the claper housing assembly.
13) slide on the caliper housing with the inner brake pad in place (over the outer brake pad) and screw in the caliper screw rods using the 7 MM allen wrench
14) on the right wheel brakes, DO NOT FORGET to slide in the brake sensor (the one with the black connector) and connect it to the connector on the caliper housing.
15) be sure to reinsert the spring clamp onto the outer brake assembly to set the assembly squarely onto the wheel (there should be no wiggle in the brake assembly after the spring clamps are installed).
16) finally mount the wheels.
17) you can bleed the brakes at this point to release any trapped air (which is unlikely) but be sure to pump the brakes after starting the car BUT BEFORE MOVING IT to re-preassurize the brake system before driving the car.
17) ONE WEEK LATER - recheck brake assembly to ensure all is okay and brake fluid.

This proposed solution is for a 2003 Mercedes Benz E320 and NOT a 2005 model as stated by the limited option selection provided by FIXYA.com when initially describing the problem.

Jul 09, 2008 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...