Question about 1999 Dodge Durango

1 Answer

Were is the crank sensor and camshaft sensor located

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Behind the harmonic balance r

Posted on Sep 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of cam and crank sensors on a 2010 colorado 4 cyl.


camshaft sensor should be next to camshaft magnet on front of engine. (LH9) crank sensor on right side of engine

Jan 25, 2016 | Cars & Trucks

1 Answer

2003 dodge caravan 3.3l cranks but no spark have replaced timing chain my bad...but i have a clicking noise sounded like chain.....replaced crank sensor it had evidence of being smaked maybe causing my...


probably forgot to reinstall camshaft sensor which located on timing cover or forgot to reconnect camshaft sensor because crankshaft sensor and camshaft sensor work together to control fuel timing and spark timing.make sure ignition coil getting 12 volts.

Aug 11, 2013 | 2000 Dodge Grand Caravan

1 Answer

2003 ford taurus 3.0 Vulcan cranks strong, you can smell the gas but it won't start. I tried replacing the ignition coil with no results.


It is one of two things. Crank shaft sensor, on timing cover, behind crank pulley. Or the camshaft syncronizer, or the camshaft sensor (sits on top of Camshaft syncronizer) Located on drivers side end of engine, in what used to be the home of the old type distributor.

Aug 27, 2011 | 2003 Ford Taurus

1 Answer

2004 escape where is the crank position sensor located?


We would recommend taking a look at the front of your motor, by either of the camshafts and where they exit the head(s). The sensor is either a optical or hall effect sensor, so try and find a housing that is near or around your intake or exhaust camshaft ( or just single camshaft) for the location of your camshaft position sensor

Jan 27, 2010 | 2003 Ford Escape

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Need to find Camshaft position sensor and crank se


CRANKSHAFT SENSOR - Under hood, center, front engine area, rear of crankshaft pulley, mounted in timing cover assembly.

afa767f.gif
CAMSHAFT SENSOR - Under hood, passenger side, upper engine area, mounted on engine in front of camshaft.
4c3af2b.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Apr 08, 2009 | 1995 Lincoln Town Car

1 Answer

Crank sensor and camshaft sensor


The crank sensor is in the top of bell housing of the transmission towards the back of the engine compartment. The cam sensor is built into the distributor.

Mar 07, 2009 | 1998 Chrysler Sebring

2 Answers

Camshaft position sensor location


crank sensor is a component used in an internal combustion engine to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on the engine.

The crank sensor can be used in combination with a similar camshaft position sensor to monitor the relationship between the pistons and valves in the engine, which is particularly important in engines with variable valve timing. It is also commonly the primary source for the measurement of engine speed in revolutions per minute.

Crank sensors in engines are usually comprised of magnets and an inductive coil. They are principally based on the Hall effect. Common mounting locations include the main crank pulley, the flywheel, or occasionally on the crankshaft itself.

Some engines, such as GM's Premium V family utilise crank position sensors which read a reluctor ring integral to the Harmonic Balancer. This is a much more accurate method of determining the position of the crankshaft, and allows the computer to determine within a few degrees the exact position of the crankshaft (and thereby all connected components) at any given time.

Dec 27, 2008 | 2004 Hyundai Santa Fe

4 Answers

1996 HONDA ACCORD CRANKSHAFT SENSOR AND CAMSHAFT SENSOR.


camshaft sensor is in distributor(requires dist. replacement) crankshaft is behind lower timing belt cover

Dec 12, 2008 | 1996 Honda Accord

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...