Question about 1991 Nissan Pickup

1 Answer

Replaced slave cylinder on clutch but clutch pedal falls to floor and does not come back up

Posted by on

Ad

1 Answer

Bleed the slave again

Posted on Sep 16, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch pedal is very loose and can't seem to change gears,pls help


If light pressure on your clutch pedal causes it to fall or easily be pushed to the floor and you cannot feel a normal point in which the clutch should engage it is quite possibly the slave cylinder. Most mechanic shops will tell you to replace the clutch and while doing the service they will replace the slave cylinder. Do you see or smell any brake fluid leaking? Brake fluid is used in the clutch hydraulic system. So if your brake fluid is low or you can see it leaking or smell it burning this would Point towards slave cylinder. There are other ways to check if your slave cylinder is working appropriately by looking under the vehicle having the clutch pedal pushed and seeing if the cylinder is engaging the transmission and then feeling for resistance.

Sep 20, 2017 | Cars & Trucks

1 Answer

New clutch installed. No pedal, stays on floor unless I bring it back up with my hand. No resistance.


`Did it bleed, did fluid come out in a steady stream? Isn't there a spring to bring the pedal off the floor?
Check the linkage of the pedal to rod to the clutch master cylinder, make sure that is all together. Any chance the master has an internal leak and won't build hydraulic pressure down at the slave? If you get it bled, then watch the slave operation while someone works the clutch pedal. The piston on the slave should extend and push the clutch fork enough to disengage the clutch.

Jul 19, 2015 | Nissan Cars & Trucks

1 Answer

Clutch pedal sinks to floor


Unless you have bled the slave cylinder properly there will still be air in it. However I think the problem is in the clutch master cylinder ---piston rubbers leaking fluid back to reservoir. Replace the m/cyl with new item and bleed out correctly.

Apr 27, 2013 | 1994 Toyota Tercel

1 Answer

95 Ford Truck - Clutch


CABLE IS FOR YOUR SPEEDOMETER. SLAVE CYLINDER NEEDS TO BE REPLACED. EVEN IF IT HAS FLUID.JACK UP THE TRUCK AND PUT IT ON STANDS OR RAMPS. REMOVE THE CLUTCH INSPECTION COVER. HAVE SOMEONE PULL THE CLUTCH PEDAL BACK UP AND PRESS IT AGAIN. IF THE THROW OUT BEARING DOES NOT MOVE ITS THE SLAVE CYLINDER FOR SURE.

Jul 22, 2012 | Cars & Trucks

1 Answer

My clutch pedal is not working. falls right to the floor. have to drive by hard-shifting. in my '88 audi 90 quattro


You have a leak and will need to replace the clutch master and slave cylinders.

Jun 11, 2012 | Cars & Trucks

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

2 Answers

Abnormal clutch pedal operation


You've replaced the master, the slave, now I would check to see if the throwout fork will move by hand. If you can move the fork by hand I would say that your pressure plate and or throwout bearing are worn out. First try to just gravity bleed the system. If that doesnt work, it may be time for a clutch, pressure plate, and bearing. The pressure plate spring pushes the pedal back up and depending on how many miles and driving habit those little arms on it break off and just wear out. I hope this helps you.

Aug 19, 2009 | 1997 Mitsubishi 3000GT

1 Answer

Soft clutch 1992 isuzu rodeo


If the seals around the shafts of master and slave are tight, they may be concealing a leak with fluid bypassing the piston seals internal to the two assemblies. Either your master or slave cylinders need to be replaced ot have new seals installed. Once you find the culprit and have installed a replacement, you will have to bleed the lines to evacuate air trap in the lines.

Mar 21, 2009 | 1992 Isuzu Rodeo

2 Answers

Clutch bleeding


Try opening bleeder screw on slave cylinder and let it GRAVITY BLEED, just open clutch mater and fill with fluid and then open slave cylinder bleeder screw and let it gravity bleed( run out by itself) When it does close bleeder screw and you should get pressure.(make sure master doesn't run out of fluid during this preocess).If pedal not good enough bleed as usual. PUMP PEDAL ABOUT 6 time then hold down to the floor using wrench open slave bleed screw and close back up with pedal still being held DOWN. Repeat until fluid comes out with out air.However if all this doesn't work, YOU WILL NEED TO REPLACE CLUTCH MATER CYLINDER. Conatct if you need more help and Good Luck. Thanks for using FIX YA

Jan 12, 2009 | 2001 Honda Civic

1 Answer

Clutch pedal floppy


The hydraulic clutch master cylinder is defective or the slave cylinder at the bell housing, it is recommended they replaced in pairs.

Dec 11, 2008 | 1991 Acura NSX

Not finding what you are looking for?
1991 Nissan Pickup Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...