Question about 1988 Mazda B2200

Open Question

My 1990 mazda b2200 wont start but it will try to turn over and it also has a vacum leak do you think a bad fuel pump could be the problem

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 651 Answers

SOURCE: I have 1987 Mazda B2200 2.2 ltre, turns, fires, no fuel psi.

look under hood to see if theres a relay there. it may need to be replaced. good luck

Posted on Dec 03, 2008

Ad
stormbrewin
  • 426 Answers

SOURCE: 1996 mazda mx6 ls cranks but won't start

you may need to run a wire from a keyed ignition source that has power while cranking and running to the fuel pump relay and bypass the pcm to test wether it will run, if it runs put a more permanent wire in place.Not too sure what tests youve done but it seems that fuel is what your focusing on so a quick test is too spray engine start up the intake tube to see if the engine trys to run if it does it eliminates a lot of other potential reasons for a no start condition.Also try squeezing the fuel return line to see if the added pressure will try to make engine run.Could be time to replace fuel pump etc anyway let me know how it goes good luck with it

Posted on Dec 12, 2008

  • 408 Answers

SOURCE: 1990 mazda b2200 starts & idle but dies if I push on the gas.

You need to run a pressure check on the fuel line with the appropriate gauge.

Posted on Mar 07, 2009

jingB
  • 19 Answers

SOURCE: mazda engine bad

yes, i believe you could put any engine on your pick-up provided it is the rear wheel type set-up and the engine comes with its own tranny. problem is, if changing the engine mounts, tranny mounts, wiring set-up and exhaust system layout would not be of any problem to you. might as well look for the same mazda engine you have as a replacement to ease installation.

Posted on Apr 14, 2009

  • 8 Answers

SOURCE: 1990 Mazda B2200 PU. Clutch sticks to the floor

I just had the same problem today it was the master cyclinder
its a common mazda problem

Posted on May 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 mazda b2200 2.2l fuel injected won't accelerate just bogs down idles fine


I think you have established that it is getting fuel but I guess what I would do is check into the throttle body itself.

May 20, 2014 | 1988 Mazda B2200

1 Answer

When im driving my truck,it starts to sputter and


I would try spark plugs and wires. If it was a fuel line you would see the leak or atleast smell it very strongly. If the problem still exists after new plugs and wires try the distributor cap.

Apr 21, 2010 | 1988 Mazda B2200

1 Answer

I need a vacume diagram for my truck it is idleing


Here is a link that will be very helpfull to you including what you need dont forget to rate my assistance thank you.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Vacuum+Diagrams&partName=Driveability+%26+Emissions+Controls&pageId=0900c15280076be3&partId=0900c15280076b68

Feb 13, 2010 | 1988 Mazda B2200

1 Answer

1990 Mazda B2200 w EFI- Starts and dies


When you turn the key to the on position can you hear the fuel pump turn on? If not, the fuel pump relay has gone bad. Make sure you have at least 5 gallons of fuel in the tank. Check and make sure you have fuel flow to the rail, try cracking the banjo bolt on the fuel rail.

Jan 24, 2010 | 1990 Mazda B-Series

1 Answer

1988 Mazda B2200 starts well, but as it warms up, the gas flow stops. I changed the fuel pump and the problem still persists. Always starts.


I would trying to either checked fuel filter or if that dosent work chang the fuel pressure regulator.

Jul 19, 2009 | 1988 Mazda B2200

3 Answers

93 mazda mx6 wont run. will start but runs very rough and only for a few seconds. plugs are black and getting too much fuel. I replaced the fuel pump, fuel filter, fuel pressure regulator. I think the...


the tps may affect the idle, but not really the excessive fuel. check that your coil has enough spark, remove plug watch spark. otherwise check haul senders in distributor or check injectors are not leaking.

Jul 14, 2009 | 1997 Mazda MX-6

1 Answer

1990 mazda b2200 starts & idle but dies if I push on the gas.


You need to run a pressure check on the fuel line with the appropriate gauge.

Mar 07, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...