Question about 1995 Ford Econoline

1 Answer

I was changing the gasket and when i took the pan off thier was a plastic piece in the pan. it look like it belong some where but i don't know where. its circle on one end with a rubber piece around it and a stem from the circle part

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 76,630 Answers

This is the dipstick tube block off plug and it is pushed into the transmission when the factory fills the transmission for the first time when the truck was built, just through it away.

Posted on Sep 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While changing the transmission pan gasket and filter i noticed a piece of plastic in the pan. it is about 2 inches long and looks like a mushroom with an o-ring on the head of it. i cant figure out where...


Hi, welcome to FixYa.com my name is Shawn and I will be answering your question.

That yellow plug is from the factory. They use that to plug the dipstick tube hole before they install the dipstick tube to keep the fluid from running out. Just throw out the yellow plastic piece. When they install the dipstick tube it pushes the piece into the trans pan where it stays until you change the fluid and throw it out.

I hope my assistance helped you and resolved your concern, if you need further assistance please ask.

Aug 09, 2011 | Mercury Cougar Cars & Trucks

1 Answer

After removing the radiator drain plug and flushing the system, I replaced the plug , added fluid, and now theres a leak coming from the drain plug, and its tight. the plug is plastic with a "built...


Hello: Yes, There should be a rubber gasket on the drain plug. It must of come off when you removed the plug. I don't think you can just purchase the gasket by itself, you might can purchase a new drain plug at a Auto Parts Store or at a GM dealership. Check the drain pan you used to drain the radiator it might still be in there. Normally you don,t have to completely remove the plug to drain the radiator.

Apr 26, 2011 | 2004 Chevrolet Aveo

1 Answer

I want to know how change my oil pan gasket.


The oil pan gasket is a complex task. Due to the design of the Northstar engine,ie the exhaust crossunder exhaust pipe either the engine has to be removed from the car or remove the transmission.... The oil pan is a two piece assembly. Upper and lower. Yhank you

Sep 03, 2010 | 1999 Cadillac DeVille

1 Answer

I have 1995 toyota camry with 2.2 liter engine.I installed a new oil pan gasket,and valve cover gasket,cause there was alot of oil leaking from that area.All the work was done about two months ago.there...


I have the same car and the same problem. I can see the oil shooting out at the (upside down) rear, right side of the oil pan. This side of the oil pan is covered by a piece of plastic foam. There are no bolts on this side of the pan. Toyota recommends grey Formagaskit to seal the pan. The natural flow for this leak is all over the bell housing. The piece of plastic foam is attached to bell housing inspection cover. Good Luck!!!

Feb 13, 2010 | 1995 Toyota Camry

1 Answer

Smoking Ram


On the intake there is a pan the gasket usually hardens and pieces break off allowing oil from block to be sucked into intake (I am assuming you have performed compression check on all cylinders and thier OK) You have to pull the intake to get to this pan.

Jan 20, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

Leaking oil pan gasket


Check the pan to make sure it is not cracked or warped. Also notice where most of the leak is coming from. When you took off the old gasket, did you scrape off all of the old material? If you used a screwdriver to do that, you may have nicked the metal and created a path for oil to leak. If you didn't scrape off the old material and any RTV sealant, you will want to, using a plastic scraper. There are sprays that dissolve this material too if it is too hard to scrape off.

If that area is nicked badly and you haven't used RTV sealant, you may want to put a small amount all over the area that the gasket will cover, not just the nicked area but the whole area that the pan gasket will cover- it doesn't take much and if you smear too much on, it will just ooze out and make things messy - just a fine coating will do.

As you tighten up the bolts, make sure you tighten in an alternating pattern as they begin to contact the gasket and get tight so a bolt on one side get fastened down as often as one on the other side gets fastened to avoid warping the pan.

Hope this helps.

Dec 27, 2008 | 1987 Ford F 150

1 Answer

Timing chain guide


does any one know were to get the pitchers to change the timing chain for free on the internet

Jul 28, 2008 | 1990 Nissan Stanza

2 Answers

Flushing the transmission


To change the transmission fluid make sure you have purchased: 1. filter with the o-ring 2. MOPAR ATF + 3 Type 7176, p/n 05010124AA fluid (I believe it took 6 quarts?) You are not changing the torque converter fluid so there will not be 12 quarts needed.). 3. Pan gasket. You should receive the new neoprene reusable pan gasket. This is because the recommendation is to change the transmission fluid every 25,000 miles. 4. There is a fluid additive to prevent foaming? Use it.


Raise the vehicle on a hoist. Remove the pan bolts. Remove the old gasket material with a plastic scraper. There could be metal transfer if you use a metal scraper. Clean the pan carefully. Clean the magnet that sits in the pan as it collects the minute metal shavings. If you see an excess of larger particles, you really should have the transmission inspected at a shop. Replace the filter carefully looking at its arrangement before removing. It took a second look to install a new filter because I did not watch how it was situated before removing. Use a thin coat of transmission fluid on the new pan gasket. Orient reusable gasket properly with bolt holes and assemble oil pan and gasket to transmission case. Tighten oil pan bolts to 19 Nm (165 in lbs.). CAUTION: DO NOT OVERFILL TRANSAXLE. DO NOT ADD OIL IF LEVEL IS BETWEEN: LOWER HOLES FOR WARM OIL (100?F). UPPER HOLES FOR HOT OIL (180?F.).

Jun 12, 2008 | Chrysler Neon Cars & Trucks

Not finding what you are looking for?
1995 Ford Econoline Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...