Question about 1988 Dodge Grand Caravan

2 Answers

Hi I am trying to change drive axel but can't get it to come out is there something special that I have to do, does it just not pull out? It is a 1998 dodge caravan. baynhamsandra@hotmail.com

Posted by on

  • baynhamsandr Sep 14, 2010

    that is what we have been doing but it won't come out

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 326 Answers

Where the axle enters the trans put a pry bar between and pry it should pop loose

Posted on Sep 14, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

IT'S JUST COMES OUT. IT HAS A CLIP AT THE END OF THE SHAFT, WITH PRI BAR FIT BETWEEN JOINT AND TRANSMISSION, AND PRI OUT, SOME TIMES THERE HARD TO COME OUT.

Posted on Sep 14, 2010

  • Alexander Mimun
    Alexander Mimun Sep 14, 2010

    It's going to be hard, but that's the only way.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace right front axel seal 2001 pathfinder


Hi,if you are talking about the drive shaft cv boot,there is a vidio on you tube showing how to change the drive shaft same perseger,hope this is helpfull,all the best,its a easy fix.

Oct 03, 2015 | 2001 Nissan Pathfinder

1 Answer

How do I change altenator on a 6 cyl front wheel drive, do I have to pull the axel to get bottom bolt out if so how


havn't said what vehicle but i doubt you would need to remove the axle , send the make ,model etc and i'll have a think cheers

Oct 07, 2014 | Cars & Trucks

1 Answer

How do i remove the axel on a toyota echo 2000 model


remove road wheel . remove axle nut , uncouple lower strut and pull disc housing out wards may have to tap axle. the axle is held in the diff housing with a c clip but come out with a sharp pull.

Sep 20, 2014 | 2000 Toyota ECHO

1 Answer

In my 1982 chevy silverado, the drive shaft won't


It sounds to me that the rear and went out. Crawl under your truck and make sure that your axle is still connected to the yoake. It would be kind of obvious cause if you'reU-joints break your axel would be laying on the ground. Your rear axle has a plug in it. Remove the plug stick your pinky him to the hole and downward trying to see if you can feel axel fluied. If you cannot most likely your ring and pinion is locked up. If you do feel oil pull your pinky out and look at it see if there is metal shavings in the oil. Good luck.

Aug 22, 2013 | Cars & Trucks

1 Answer

Need to front pull front axel on the passanger side of a 94 toyota pickup not sure how to disassemble the four wheel drive hub to get the axel out


Here's a manual for the '93. As '94 was the last year of the pickup (not Tacoma) I don't imagine much changed: http://www.ncttora.com/fsm/1993/suspensionandaxle.html

Feb 13, 2011 | 1994 Toyota Pickup

3 Answers

GMC '91 Jimmy, Transfer case. When in two wheel drive I hear a slight grinding noise and rattling noise. When in 4 wheel no noise. 330,000 miles, could something be worn? What keeps the transfer case gear...


Remove the transfer case and strip it down,wash it out and replace whatever is worn.
330,000 miles is unrealistic
Your chain is worn and stretched for sure, and rattling and may be cutting into the case.
Don't install another salvage yard unit, unless you can not repair yours. Then strip down whatever you purchase, and go thru it also.

Sep 17, 2010 | 1991 GMC S-15 Jimmy

1 Answer

1993 Dodge Grand Caravan Transmission issue


A broken engine or tranny mount should not cause a front wheel to wobble. If this is happening with a grinding noise I'd expect more of a failing bearing or such. The grinding noise may also be a rotor of the brakes with poor pads. Yes, if a axel, or CV joint, is failing this can make noise too, often times a "clicking" type of noise. Best get the front of the van up on jack stands, remove the tires and inspect all of the front-end components; pay special attention CV joints, rotors and front axel area, loose movement in the axels?
I hope this may have helped,
Tom

Apr 16, 2010 | 1993 Dodge Caravan

1 Answer

85 cj7 rear axle removal


Do you have bolt in axels? or are they held in with C- clips? If its bolt in axels you need to remove the bolts, and you may need an axel puller to get them out. If its got C- clips rear cover on rearend has to come off, and pin has to be removed to get C- clip out to get axel out.

Apr 03, 2009 | 1986 Jeep CJ7

2 Answers

Rattle in 2005 Sunfire


have you tried jacking it up and pushing and pulling on the wheels to try to get a noise theres probably more going on but it could be something simple as just a loose nut or bolt. u can check your mounts by applying the hand brake and in gear give it a little gas have some one check to see if they are having to much movement

May 26, 2008 | 2005 Pontiac Sunfire

Not finding what you are looking for?
Cars & Trucks Logo

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...