Question about Pontiac Aztek

Open Question

Loking for torque specs for rocker arms on 2000 aztec 3400 also related specs for vlve cover and upper intake changing lower intake gaskets

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Posted on Dec 02, 2008

  • 124 Answers

SOURCE: I am changing intake gaskets

89 inch pounds then 30 degrees. make sure the push rods get put back in same place they came out they are different lengths. If you ever do another one of these buy the tool for the rocker arms and you will not have to remove them or the rear valve cover. please rate

Posted on Dec 27, 2008

  • 173 Answers

SOURCE: what is the torque of the rocker arms on alero 2003 3400 engine

14 ft/lbs first pass on all then an additional 30 degrees for all on final pass ..by the way 1 bolt flat to the next bolt flat is 60 degrees so all nuts get half a bolt flat final torque if ya wanna throw caution to the wind torque it to 16 ft lbs and be done with it. lol these specs are from gm ok. good luck and ps the intake pushrods are shorter than the exhaust pushrods and there is no clearance if you get them in wrong an apprentice found this out 3 years ago and a lot of people saw what happens lol..good luck

Posted on Nov 24, 2009

ftw1952
  • 10319 Answers

SOURCE: whats the torque spec for rocker arms on a 1992

35 90 25

Posted on Jan 30, 2010

  • 617 Answers

SOURCE: intake manifold bolts torque and rocker arm torque

Intake Manifold Coolant Pipe Bolt .... 89 in lbs (7.4166 ft. lbs)
Lower Intake Manifold Bolt .............. 115 in. lbs (9.5833 ft. lbs)
Upper Intake Manifold Bolt/Stud ...... 18 ft. lbs
Valve Rocker Arm Bolt ................... 168 in. lbs (14 ft. lbs +30 degress

Posted on Feb 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the correct torque specs. for lower intake manifold and upper, and rocker arm torque for 02 Buick Rendezvous 3.4 v-6 are the rocker arms pre load non adjustable


Call any major autoparts store for the correct answer. There are updated torque specs for the gm 3.4 vs in order to deal with a common issue of leaking intake manifold gaskets. They should have the correct updated spec for you vehicle based on the specific Vin number

Feb 01, 2017 | 2002 Buick Rendezvous

1 Answer

Rocker arm torque spec and intake manifold torque spec and pattern


I could not answer this any better than what I have found online. Here is a guy that has posted removal and re-installation in great detail as well as great photos.
LIM and Head Gasket Change Walkthrough FAQ GrandAmGT com Forum

I give all the credit for this answer to the poster.

Sep 12, 2014 | 2002 Pontiac Grand Am

3 Answers

Do I have to take the timming belt off to do a head gasket on a 1999 chevy malibu v6 3.1L


The 3.1 engine does not have a belt,it is a chain motor.You do not need to remove timing chain to remove head.

Apr 12, 2011 | 1999 Chevrolet Malibu

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Intake manifold bolts torque and rocker arm torque


Intake Manifold Coolant Pipe Bolt .... 89 in lbs (7.4166 ft. lbs)
Lower Intake Manifold Bolt .............. 115 in. lbs (9.5833 ft. lbs)
Upper Intake Manifold Bolt/Stud ...... 18 ft. lbs
Valve Rocker Arm Bolt ................... 168 in. lbs (14 ft. lbs +30 degress

Feb 06, 2010 | 1999 Buick Century

1 Answer

Intake torque specs


Upper intake

Stage 1: Tighten to 20 Nm (14 lb-ft).
Stage 2: Tighten to 25 Nm (18 lb-ft).


Lower intake

Stage 1: Tighten to 15 Nm (11 lb-ft).
Stage 2: Tighten to 32 Nm (24 lb-ft).


Rocker Arms

Stage 1: Tighten to 10 Nm (89 lb-in).
Stage 2: Tighten to 32 Nm (24 lb-ft).

May 17, 2009 | 2000 Ford Windstar

2 Answers

I am changing intake gaskets and need the torque specs. for the rockers 2002 pontiac aztek 3400


89 inch pounds then 30 degrees. make sure the push rods get put back in same place they came out they are different lengths. If you ever do another one of these buy the tool for the rocker arms and you will not have to remove them or the rear valve cover. please rate

Dec 27, 2008 | 2002 Pontiac Aztek

1 Answer

Intake and rocker arm torque specs. thanks


on 3.1 v6 it is--rocker arm bolts--- 89 in-lbs,intake manifold(lower)---step 1-62 in-lbs step 2 115 in-lbs. for year 1997 3.1,

Dec 26, 2008 | 1997 Chevrolet Malibu

4 Answers

Engine Bolt Torques- 2005 Chevy Impala/3400 Engine


Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

Jun 28, 2008 | 2005 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

571 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...