Question about 2008 Hyundai Tucson

1 Answer

Look for a crank shaft for a 2007 hyundia h-100 series

Posted by on


1 Answer

Click on this link below to order a replacement crank shaft

Posted on Sep 14, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i remove the crank shaft pulley on a 2005 Hyundia Sonata LX

Undo the nut and put a pulley extractor on the end of it and tighten the bolt on the extractor. The pulley will come off the shaft. Don't loose the keyway.

Mar 30, 2016 | Cars & Trucks

1 Answer

I can't turn the dome light off in my Hyundia 2007 Santa Fe, why?

Pull the light bulb. It's easier and it won't disable any other circuits.
Really. The fuse may also power your tail lights, or dash lights, etc.
Sounds like the problem is in the dome light fixture itself.

Aug 19, 2014 | Cars & Trucks

1 Answer

2007 hyundia tucaon 2.0 replaced timing belt and had to replace intake valves car crank and ran and then shut off now it fires to the plugs and when spinning over the fire stops

recheck the timing. was number one piston at top dead center when u lined up the timing marks? if not then timing would be off causing problem u stated

Apr 06, 2014 | 2009 Hyundai Tucson 2.0

1 Answer

I have a revtech 2003 100" 4x4 engine the crank snapped off on the oil pump side any idea why ???

crank shafts snap from bad machining ---block out of align bending the crank while turning--excessive rpm's-- crank shaft unbalanced
Bad machining is where the radius at the point where there is a right angle change of direction and there is not a small radius at that point --stress build up at that point creates cracks and failure.
block out of alignment means that the block has to be line bored to make all the bearings exactly in the same line ( possibly a main cap was installed incorrectly)
Excessive rpm's will crack a crank shaft if it is a dropped forged crank and not a high rpm billeted steel crank
Crank shaft unbalanced from flywheel and balancing shafts not properly timed

Apr 03, 2014 | Cars & Trucks

1 Answer

Timing marks for CRANK SHAFT ON 2005 jaguar XJ

there is no marks the ign timing is ecu controlled a locking device goes in the flywheel housing where the crank sensor fits to time the valve timing and locking bars fit over the camshafts.sounds

Feb 01, 2014 | 2005 Jaguar XJ-Series

1 Answer

I need to know where the crank shaft censor located in a 2002 hyundia accent 1.6 L

Mar 17, 2013 | Cars & Trucks

1 Answer

Changing timing belt on hyundia accent

Make sure the crank pulley is lined up with the top dead center mark. The make sure the crankshaft is lined up with its mark. Its easier if you can line the marks up before you take the old belt and try not to move the crank shaft are cam pulley.

Apr 17, 2010 | 2002 Hyundai Accent

1 Answer

2007 Hyundia Sonata Brake Lights

There was recall for the 2006 and 2007 Hyundai Sonata Brake Light Switch assembly.

Apr 27, 2009 | 2006 Hyundai Sonata

Not finding what you are looking for?
2008 Hyundai Tucson Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides