Question about 1995 Mazda 626

1 Answer

How do you replace the starter scensor on a 1995 Mazda 626

Posted by on

Ad

1 Answer

To replace your crankshaft position sensor, jack the car up and go near the water pump at the front of the car, and remove components that block access to the sensor. This may include removing parts like the water pump which could be in the way. Once accessible, remove the two bolts holding the sensor into place, remove the wires that send the data, and place in the new part.

Posted on Sep 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the theft deterrent system located on a 1995 mazda 626


1995 Mazda Theft deterent you dont have one. there is a keyless entry. a ant theft radio deterent. So you probable are having problem starting like turning over maybe the starter is non op or even a dead battery. So what does it do?

Feb 24, 2012 | 1995 Mazda 626

2 Answers

1995 mazda 626 4 cylinder starter clicks but wont turn over i replaced battery thinking it was that no luck i just replaced starter and solenoid same result justs clicks i cleaned all my connections so...


check for a fuseable link in the wire going from the battery to the starter , if its bad you'll get clicking , check the relay for the starter,, locate where the clicking is coming from, and check that relay

Jun 22, 2011 | Mazda 626 Cars & Trucks

1 Answer

How many bolts hold a starter on in a Mazda 626 1995?


there are 3 bolts holding it to the transmission bell housing, see picture below.


ced404c.jpg

Apr 03, 2010 | 1995 Mazda 626

1 Answer

My 1995 mazda 626 4 cyl wont start. its getting gas spark. when you turn the moter over you hear like a muffeled noise at the moter not muffler


Your problem could be a lot of things ,,without hearing the noise we have to gess your problems like
1Chech the engine for turning over if not then its the starter bendix slipping and if it is turning over as usual then its could be the starter ring on the flywheel and if so turn key off and turn engine over by hand about 1/2 way around on bottom pully and try starting again and if it starts then its the starter ring.
Engine or Gearbox out job.
Let me know how you get on . Ron

Nov 11, 2009 | 1995 Mazda 626

2 Answers

I need to replace an alternator belt for my 1995 Mazda 626.


the letters should be on the fender or back trunk lid. if there is nothing there then it will be LX

Mar 17, 2009 | 1995 Mazda 626

1 Answer

Need help


start off in order
remove earth from battery
remove
starter motor
drive shafts
clutch slave
bellhousing bolts
if auto remove torque converter bolts
wiggle out gearbox

Jun 29, 2008 | 1995 Mazda 626

3 Answers

Does not crank


it could be a bad connection or a broken ignition switch maybe a fuse blew

May 30, 2008 | 1995 Mazda 626

Not finding what you are looking for?
1995 Mazda 626 Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...