Question about 1999 Hyundai Sonata

1 Answer

Need location of vapor canister and purge valve in 1999 sonata v-6. any help with evap system is appreciated.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

The Canister Is located on the rear drivers side under the car (Big black box with 3 rubber lines). And the purge valve is located on the in the center on the back of the intake manifold (2 rubber lines and 1 plug).

Posted on Nov 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is purge sensor located


There is no such thing , What code do you have if any ? There is a purge solenoid for the EVAP system ! evaporative emission system. An there is a vent solenoid , a fuel tank pressure (FTP) sensor.
The evaporative emission (EVAP) control system limits fuel vapors from escaping into the atmosphere. Fuel tank vapors are allowed to move from the fuel tank, due to pressure in the tank, through the vapor pipe, into the EVAP canister. Carbon in the canister absorbs and stores the fuel vapors. Excess pressure is vented through the vent line and EVAP vent valve to atmosphere. The EVAP canister stores the fuel vapors until the engine is able to use them. At an appropriate time, the control module will command the EVAP purge valve ON, open, allowing engine vacuum to be applied to the EVAP canister. With the EVAP vent valve OFF, open, fresh air will be drawn through the valve and vent line to the EVAP canister. Fresh air is drawn through the canister, pulling fuel vapors from the carbon. The air/fuel vapor mixture continues through the EVAP purge pipe and EVAP purge valve into the intake manifold to be consumed during normal combustion. The control module uses several tests to determine if the EVAP system is leaking.

Jul 26, 2016 | GMC Sierra Cars & Trucks

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

P0446 ford escort 98


This Pinpoint Test is intended to diagnose the following:
  • Canister vent (CV) solenoid (9F945) (electrical concern only)
  • Fuel filler cap (9030)
  • Fuel tank pressure (FTP) sensor (9C052)
  • EVAP canister tube (fuel tank to EVAP canister)(9A228)
  • Fuel canister purge outlet tube (EVAP canister to EVAP canister purge valve) (9D661)
  • EVAP return tube (EVAP canister purge valve to intake manifold) (9G271)
  • EVAP canister purge valve (9C915)
  • Vacuum source line (input port vacuum to intake manifold)
  • Harness circuits: CV, FLI, FTP, EVAP Canister Purge Valve, SIG RTN, vehicle power (VPWR), reference voltage (VREF) and power ground (PWR GND)
  • Powertrain control module (PCM) (12A650)
This Pinpoint Test is used as an assistance in diagnosing the following EVAP components:
  • EVAP canister and bracket assembly (9E857)
    • EVAP canister sleeve assembly (fitting)(9D925)
    • Canister vent (CV) solenoid - hose assembly (9F976 or 9K318)
    • EVAP canister (9D653)
    • Canister vent (CV) solenoid (9F945)(mechanical concern only)
  • Fill limit valve assembly (9A086)
  • Fuel filler pipe flapper valve (9B085)
  • Fuel filler pipe check valve (9189), assembly (9285)
  • Fuel tank filler pipe (9034)
  • Fuel tank assembly (with fuel vapor vent valve) (9K007)
  • Fuel tank assembly (without fuel vapor vent valve) (9002)
  • Fuel vapor control valve (9B190)
  • Fuel vapor vent valve (9B593)
  • Liquid/vapor fuel discriminator (9G332)
  • On-board refueling vapor recovery (ORVR) T - connector assembly (9S314)
Description For additional information on the Evaporative Emission (EVAP) System, refer to Section 1A .
For additional information on the Evaporative Emission System Monitor, refer to Section 1A .
Pinpoint Test Schematics Escort/Tracer (2V)
aa3060b.gif

May 28, 2011 | 1998 Ford Escort

2 Answers

Check engine lite came on code is p1443 what does this code mean


P1443 Evaporative Emission Control System Control Valve The Evaporative Emission Control System monitors the fuel vapor flow between the engine intake manifold and the EVAP canister. The system failure occurs when a leak or blockage between the intake manifold, the EVAP canister purge valve and the EVAP canister is detected by the PCM.

Code P1443 Possible Causes:

- Pinched, blocked or plugged fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister

- Disconnected, cracked or cut fuel vapor tubes/hoses (except between fuel tank and EVAP canister)

- Damaged EVAP canister purge valve

May 04, 2011 | 1997 Ford Escort

2 Answers

Ford escort wagon 1997 code p1443 displayed. what does this indicate & where is the cannister? thank you.


P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:
  • Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.
  • Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.
  • Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.
  • EVAP canister purge valve stuck closed (mechanically).

  • Possible Solution:
    Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

    The canister is on the passengers side near the firewall if I recall correctly.

    Jan 18, 2011 | Ford Escort Cars & Trucks

    2 Answers

    Codigo p1440


    EVAP System Vent Circuit Malfunction

    This diagnosis detects leaks in the Evaporative Emission (EVAP) purge line using of vapor pressure in the fuel tank. The EVAP canister vent control valve is closed to shut the EVAP purge line. The vacuum cut valve bypass valve will then be opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP control system pressure sensor can now monitor the pressure inside the fuel tank. If pressure increases, the Engine Control Module (ECM) will check for leaks in the line between the vacuum cut valve and EVAP canister purge volume control solenoid valve.

    Possible causes
    - Incorrect fuel tank vacuum relief valve
    - Incorrect fuel filler cap used
    - Fuel filler cap remains open or fails to close
    - Foreign matter caught in fuel filler cap
    - Leak is in line between intake manifold and EVAP canister purge volume control solenoid valve
    - Foreign matter caught in EVAP canister vent control valve
    - EVAP canister or fuel tank leaks
    - EVAP purge line (pipe and rubber tube) leaks
    - EVAP purge line rubber tube bent
    - Blocked or bent rubber tube to EVAP control system pressure sensor
    - Loose or disconnected rubber tube
    - EVAP canister vent control valve and the circuit
    - O-ring of EVAP canister vent control valve is missing or damaged
    - EVAP canister is saturated with water
    - EVAP control system pressure sensor
    - Absolute pressure sensor

    Possible solution
    - Loose fuel filler cap
    - Leaking fuel filler cap


    Hope helps (remember to rate this answer).

    Jan 05, 2011 | 2000 Hyundai Sonata

    2 Answers

    Code says evaporator purge solenoid


    Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

    P0440 Evaporative emission (EVAP) system - malfunction

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0441 Evaporative emission (EVAP) system - incorrect flow detected

    Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


    P0442 Evaporative emission (EVAP) system - small leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

    Possible causes: Wiring, EVAP canister purge valve, ECM


    P0444 Evaporative emission (EVAP) canister purge valve -open circuit

    Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


    P0445 Evaporative emission (EVAP) canister purge valve -short circuit

    Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


    P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

    Possible causes: Wiring, EVAP pressure sensor, ECM


    P0455 Evaporative emission (EVAP) system - large leak detected

    Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


    P0456 Evaporative emission system - very small leak detected

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


    P0457 Evaporative emission system - leak detected (fuel cap loose/off)

    Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


    P0458 Evaporative emission system, purge control valve -circuit low

    Possible causes: Wiring short to earth, EVAP valve


    P0459 Evaporative emission system, purge control valve -circuit high
    Possible causes: Wiring short to positive, EVAP valve


    Evaporative Emission Purge Solenoid

    Description & Operation
    The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
    During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
    The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
    Removal & Installation
    The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

    1. Disconnect electrical connector at solenoid.
    2. Disconnect vacuum lines at solenoid.
    3. Lift solenoid slot from mounting bracket for Removal & Installation.

    To Install:
    1. Position solenoid slot to mounting bracket.
    2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
    3. Connect electrical connector to solenoid.
    Purge solenoid location:

    jturcotte_65.gif
    EVAP cannister location:
    jturcotte_66.gif

    Nov 05, 2010 | 2000 Jeep Grand Cherokee

    2 Answers

    My 1999 toyota corolla check engine is on for a year.I took it to smog test and they said it will fail the test.What should I do now? How can I turn the light off?


    A code P0441 could mean one or more of the following has happened:
    • Bad vacuum switch
    • Broken or damaged EVAP line or canister
    • Open in PCM purge command circuit
    • Open or short in Voltage feed circuit to Purge Solenoid
    • Faulty purge solenoid
    • Restriction in EVAP solenoid, line or canister
    • Corrosion or resistance in purge connector
    • Bad PCM Evaporative Emission Control System Incorrect Purge Flow
      What does that mean? This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister
      , purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
      EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank
      into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.

    Jan 28, 2010 | 1999 Toyota Avalon

    2 Answers

    What is he code 455 for a 2006 hyundai sonata means


    CODE PO455 EVAPORATIVE EMISSION SYSTEM LARGE LEAK DETECTED.POSSIBLE CAUSES CANISTER VENT SOLENOID MAY BE STUCK IN OPEN POSITION / EVAP CANISTER TUBE EVAP CANISTER PURGE OUTLET TUBE OR EVAP RETURN TUBE DISCONNECTED OR CRACKED OR CANISTER IS DAMAGED / EVAP CANISTER PURGE VALVE STUCK CLOSED OR CANISTER DAMAGED / FUEL FILLER CAP MISSING LOOSE NOT TIGHT OR THE WRONG PART / FUEL VAPOR HOSES TUBES BLOCKED OR RESTRICED OR FUEL VAPOR CONTROL VALVE TUBE OR FUEL VAPOR VENT VALVE ASSEMBLY BLOCKED /FUEL TANK PRESSURE SENSOR HAS FAILED MECHANICAL FAULT /FUEL TANK CONTROL VALVE IS CONTAMINATED DAMAGED OR HAS FAILED.

    Oct 21, 2009 | 2006 Hyundai Sonata

    Not finding what you are looking for?
    1999 Hyundai Sonata Logo

    938 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8499 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...