Question about 1999 Chevrolet Malibu

1 Answer

Blower or resistor on 99 malibu?

Can anyone tell me where to go to view a pic online of the blower resistor,and also the one on my 99 malibu was working on 3,4,5,and now itsnot blowing at all on any setting,would it be the blower motor or the resistor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Expert
  • 611 Answers

The resistor gmpartsdirect.com usualy has good diagrams or go to the libruary n get a service book

Posted on Jun 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater Blower not functioning


the blower motor resistor is likely bad.check the connector as well and make sure it is not burned. 99 percent sure resistor is bad.common problem

Nov 26, 2013 | 2003 Chevrolet Malibu

1 Answer

How do I tell if it is the heat resistor or the blower moter in my 2003 chevy malibu is the problem?


that can be a relay also.. It is hard to test the resistors. look under the hood for the relays

Nov 21, 2012 | 2003 Chevrolet Malibu

1 Answer

I have a 2006 Dodge Ram diesel. Can you tell me where the resistor for the blower motor is located ?


It's right next to the blower, above the passenger's feet. See pic below.


jturcotte_37.jpg
  1. Disconnect and isolate the negative battery cable.
  2. Reach under the instrument panel near the blower motor and disconnect the wire harness connector from the blower motor resistor.
  3. Remove the two screws that secure the blower motor resistor to the HVAC housing.
  4. Remove the blower motor resistor from the HVAC housing.

Nov 30, 2010 | 2006 Dodge Ram 2500

1 Answer

I need a layout for the resistor for the a/c fan speed control in a '99 Malibu


I do not have the diagram for you. but i can tell you how to change it! first, its behind glove box. to make things easier remove the glove box. remove insulating pad from underneath glove box, next loosen and slide the ecm to one side. now you can see resistor and blower motor. resistor is beside blower motor. remove wiring to resistor. take out the screws that hold it in. then pull it out of heater box. have a good day !!

May 17, 2010 | 1999 Chevrolet Malibu

1 Answer

2005 malibu - heat/ac has 4 levels for fsn, level


Your blower speed resistor has gone bad and needs to be replaced. You can pick one up at Auto Zone or Parts Source with the step by step instructions to getting the resistor replaced with common tools.

It is located under the glove box, way in the back of the passenger foot area. You'll need to remove 2 screws with a 7mm socket, and remove the plastic cover that covers the blower motor and another component box that I think controls the passenger airbag. After removing the plastic cover you'll need to side that passenger airbag module to the right so it pop off its mounting bracket and move it out of the way. That will give a better view of the blower motor. I highly recommend you also remove the blower motor itself because the Blower Motor Resistor is located behind it. I think you'll need a 5mm or 5.5mm socket to remove the 3 screws that hold in place the blower motor and 2 more screws for the Blower Motor Resistor... It's a cramped location to work in but if you have all the tools and enough lighting then it shouldn't take more than 30-60 minutes to do. The Blower Motor Resistor costs about $19-$25. Good luck

Nov 30, 2009 | 2005 Chevrolet Malibu

1 Answer

Replace blower motor resistor unit on 99 Malibu ?


the blower motor resistor is below glove box. remove panal under box. slide the pcm out of the way, resistor is beside blower motor. unplug wiring, take out screws holding it in then pull straight out to remove.

Jul 10, 2009 | 1999 Chevrolet Malibu

1 Answer

Blower motor fuse is located 99 mercury cougar


SECTION 412-04: Control Components 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Blower Motor Resistor Removal
  1. Remove the upper footwell trim panel (passenger side).
    • Remove the pushpins.
  1. Disconnect the blower motor resistor electrical connector.
  1. Remove the blower motor resistor.
-------------------------------------------------------------------------
f9d16f6.gif

May 06, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

558 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...