Question about 2001 Toyota Tundra

2 Answers

Hello, i would like to disable my alarm system when truck is idle. where is tha fuse for it also? thanks

Posted by on

  • wguerin730 Sep 14, 2010

    the $9.99 per mo. with the first month free offer, is it still available to me?





    thanks

  • wguerin730 Sep 15, 2010

    hello,



    i removed the fuse that i found..then i pulled a relay off that solved the problem with the alarm system. but now my truck won't start...the relay is (tyco VF4-45F11)..I now need to know how to bypass this relay, so my truck will start.





    thanks,



    will

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,272 Answers

Try turning the key on, press and hold in that
button until you here the alarm chirp.
Then turn off the key.
This is over ride for most after market alarms.
Now it will act as if there was no alarm at all
until your re do the steps.
----------- Check out.Keep updated Thanks.

Posted on Sep 14, 2010

  • raj somaiya
    raj somaiya Sep 15, 2010

    The relay is controlled by ecu.The ground wire connection from relay to ecu has to be disconnected or hardwired.This will stop the relay from getting command from car computer module.But this is not advisable.But to check and confirm the fault you can try this.
    Thanks for keeping updated with your query.

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 516 Answers

Take a look around the kick panel on the driver's side. It would be a small toggle or push button switch that is activated by turning your ignition key to the run position and flipping/pushing the switch. Some systems require pushing the switch more than once. If you can not find the switch, disconnect your vehicle battery (to stop the alarm from sounding while working on it). Take down the dash panel under the steering column and follow back the harness from the ignition switch. There will be wires that were tapped into this harness that lead to the brain of the system. Pulling the fuses from the brain should disable the system.

Posted on Sep 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fuse for disarming alram system


There isn't one the alarm if factory fitted is integrated into the ecm so to disable the alarm you would need to disable the engine control module

Jan 25, 2017 | Cars & Trucks

2 Answers

Isn't there a fuse I can pull to disable factory alarm system?


Sorry to say this but the answer is no as it is part of the engine control system
and if you could just bypass the alarm by pulling a fuse what use would it be as an anti theft device

Nov 01, 2016 | Cars & Trucks

2 Answers

My car alarm / key remote broke, I believe it is a factory alarm. I don't want the horn to go off, what do I do to disable the alarm system once I open the door


You may be able to disable the alarm, by opening the door with the key. Or pull the fuse, to the alarm system in the fuse box. Open your key fob remote, and check the internal 3v battery as well. It could be dead, or the (outer) case buttons are not making contact with the board which has the actual buttons on it. When pressing the buttons manually on the board they should make a "click", else wise they are the source of your problem in the remote.

Oct 30, 2014 | 2005 Kia Sedona

1 Answer

Just bought a 2000 Isuzu Rodeo that didn't come with an owners manual or a clicker for the alarm system. How do I disable the alarm. Is there a switch in the vehicle that would disable the alarm? The...


There are fuses associated with the security system that you might try pulling out. The car may not start though if the circuit is not made.

You might want to consider buying a new remote. It can be programmed to your car and you can leave the security system intact.

Apr 15, 2011 | 2000 Isuzu Trooper

1 Answer

Hi there, The car alarm on my 2007 Camry keeps going off randomly. I don't really want a car alarm. How do you disable it? Thanks, Richard


can you check under hood, there is a fuse box, remove fuse box lid, inside is printed names of circuits if you have an alarm circuit , remove that fuse, then check if car starts and runs, if so, alarm is disabled.

Jun 13, 2010 | 2007 Toyota Camry

2 Answers

Lost remote to disable alarm on 2000 mercury villager how can i disable it and start my van


If you have the factory alarm system, you can put your key into either door and lock and unlock the door, that signals the computer to deativate the alarm. If you have an aftermarket alarm system installed, it will have to be removed and the wiring that the alarm ties into must be restored to factory design.

Apr 23, 2010 | 2000 Mercury Villager

1 Answer

Were is the fuse box to disable the car alarm?


Hello. These car alarms are tied into several systems within your vehicle. There is more to disabling it than pulling a fuse. I recommend that you look in the yellow pages under auto electric and call a few repair shops that specialize in this work. Joe

Mar 05, 2010 | 1994 Oldsmobile Eighty Eight

3 Answers

How to disable alarm system


I have 96 dodge caravan and I need to disable the alarm system too and I don't know how!

Apr 20, 2009 | 1996 Dodge Caravan

1 Answer

Factory security system


I had an aftermarket alarm on a Wrangler and encountered the same problem. With the car off I disconnected the battery, then pulled the fuse(s) for the alarm. I waited to reconnect the battery for about 10 minutes because the computer can hold memory with no power source for a short amount of time. (I did not put the alarm fuses back in.) This disables the alarm, but atleast the Jeep started.

Nov 22, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Toyota Tundra Logo

Related Topics:

355 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...