Question about 2001 Mazda 626

2 Answers

I have a Mazda 626 2001 and my idle is really bad when you turn on the A/c and put it in to gear. why

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 14,036 Answers

SOUND LIKE IDLE AIR CONTROL VALVE NOT WORKING.CHECK HOSES AND PORTS MAKE SURE NONE STOPPED UP WITH CARBON.

Posted on Sep 14, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 17,129 Answers

The auto vacum is not resetting the tuning to the pump. So you will require a good trim up with calibration to set the idle and A/C idle and with the clutch depressed to be set with corrrect tuning and timing.

Posted on Sep 14, 2010

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rockitman187
  • 2559 Answers

SOURCE: 1995 mazda 626 stalling at low idle

Check the EGR valve



Please rate this a fixya

Posted on Feb 11, 2009

aaangie220
  • 202 Answers

SOURCE: i have a 93 mazda mx3 4cyl 5sp. it is really hard to put in gear

sounds like the clutch is going to need replacement and while there you should change the slave cylinder too

Posted on Aug 06, 2009

  • 4044 Answers

SOURCE: 2001 Mazda Tribute V6 engine miss

Take the vehicle to Auto Zone or another parts store that will read the engine fault code from the ECM for you. Most will do it for free. Depending on how long it has been since you replaced the plugs and wires on your vehicle you may have a bad spark plug or plug wire that is causing the problem. Easy enough to fix if you don't have to pull the air intake assembly to change the back 3 plugs. If you do have to pull this you should get a chiltons repair manual so you ahve instructions on how to remove and replace the intake assembly.

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine stall when put into gear.


There are a few possibility on this one. If you run it out of gas or really low on gas you could of sucked junk up from the bottom of the tank and you will need to replace your fuel filter. Another is that your fuel pump us going bad and you would need to check the pressure. Your throttle position sensor may have gone bad. Your idle control valve is another. Your map sensor or mas sensor could be bad

Apr 22, 2014 | 2000 Dodge Ram 1500 Truck

1 Answer

2006 mazda 6 bad idle and shuts off no power


have the fault codes read have a pressure test done on the fuel manifold to check for pump/ regulator and filter. Check the injectors for blocked tips.

Feb 05, 2014 | 2006 Mazda 6

1 Answer

I have a mazda astina ba 95 just had a clutch change after this has been done it has gotten 2 problems which were working fine before the change, problem 1 is when put into gear doesn't matter what...


Check the throttle cable for incorrect adjustment with the A/C turned off. Adjust cable to obtain 850 rpms. The A/C on will increase idle speed, which is a normal function. Check the speedo cable for correct connection at the back of the transmission case. make sure hand tight at the drive.

May 29, 2017 | Mazda Cars & Trucks

1 Answer

My 2000 model mazda protege makes a clunk when making sharp turns, accelerating or shifting from 1st to 2nd gear?


Sounds like a bad cv joint. Easy way to check is to raise the front of the vehicle so both front tires are off the ground. Use jack stands under the vehicle and block the rear tires. Start the engine and put the tranny in drive. Let the front wheels rotate while the engine is idling and turn the steering wheel slowly in both directions. Listen for the clunking noise. You may have to speed the engine up a little to make it work.

Jan 12, 2011 | 2000 Mazda Protege

1 Answer

2001 Mazda Tribute V6 engine miss


Take the vehicle to Auto Zone or another parts store that will read the engine fault code from the ECM for you. Most will do it for free. Depending on how long it has been since you replaced the plugs and wires on your vehicle you may have a bad spark plug or plug wire that is causing the problem. Easy enough to fix if you don't have to pull the air intake assembly to change the back 3 plugs. If you do have to pull this you should get a chiltons repair manual so you ahve instructions on how to remove and replace the intake assembly.

Sep 17, 2009 | Mazda Tribute Cars & Trucks

2 Answers

I have a 93 mazda mx3 4cyl 5sp. it is really hard to put in gear


sounds like the clutch is going to need replacement and while there you should change the slave cylinder too

Aug 06, 2009 | 1993 Mazda MX-3

1 Answer

1995 mazda 626 stalling at low idle


Check the EGR valve



Please rate this a fixya

Feb 11, 2009 | 1995 Mazda 626

3 Answers

Mazda mpv engine idle problem


I had the same problem with my 2002 MPV. I ended up removing the IAC Idle are-control myself, and cleaning it really well (with some air intake cleaner). Put it back together, and it's been running great for the past year.

Not too difficult of a project, I'm no mechanic, but if your good with tools, it's not to bad.

Aug 04, 2008 | 2002 Mazda MPV

Not finding what you are looking for?
2001 Mazda 626 Logo

Related Topics:

343 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...