Question about Ford E-250

1 Answer

Where is the Crankshaft located on a Ford 98 E250 5.4V8

Posted by on

  • anninos Sep 14, 2010

    Is there a diagram of this sensor? Thanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

Removal & Installation - 4.6L, 5.4L & 6.8L Engines

Where is the Crankshaft located - a884066.jpg

Fig. Remove the retaining bolt for the CKP sensor and remove the sensor from the front cover (click for zoom)

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belt from the engine.
  3. Raise and safely support the vehicle.
  4. Remove the A/C compressor mounting bolts, but do not disconnect the A/C lines. Remove and support the compressor out of the way.
  5. Detach the electrical connector for the CKP sensor.
  6. Remove the CKP sensor retaining bolts and remove the CKP sensor.
To install:
  1. Installation is the reverse of removal.

Hope helps (remember to rate and comment this).

Posted on Sep 14, 2010

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 285 Answers

SOURCE: crankshaft sensor located 98 jeep grnd cher 4wd 6cy

it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Posted on Sep 23, 2009

Testimonial: "Everything was just like you said but as a not atleast for my jeep it is an 11mm not 13mm. Works great so far (keep fingers crossed) "

  • 14036 Answers

SOURCE: 98 Ford Escort zx2 2.0L 4 cyl 5 speed transmission PVC Valve

LOOK ON INTAKE AROUND AIR FILTER HOUSING AND VALVE COVER.

Posted on Apr 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't locate my crankshaft sensor on my 1995 ford probe


Look on the link below. There's a few images which will help you locate that sensor:

location of 1995 ford probe crankshaft sensor Google Search


The sensor will be located located where the engine attaches to the transmission. Have a look around where the engine attaches to the transmission .. top, sides and underneath. The crankshaft sensor will have a minimum of 1 wire attached.

You'll locate it easily

Apr 22, 2016 | Ford Cars & Trucks

1 Answer

Edge. where is crankshaft position sensor located?


Hi Rusty, There's two links below showing the position of 2005 Ford Explorer Crankshaft Position Sensor and the 2008 ford edge camshaft sensor location. It seems like they're all in the same position, I hope this helps.....CHEERS
..
2005 Ford Explorer Crankshaft Position Sensor Location

2008 ford edge camshaft sensor location

Apr 02, 2016 | 2003 Ford Ranger

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Crankshaft position sensor on and olds 98


Should be behind the crank pulley under the water pump.

Jun 10, 2013 | Cars & Trucks

1 Answer

02 ford taurus crankshaft position sensor location


Its located in the front of the engine mounted to the timing cover near the crankshaft pulley.

Oct 29, 2012 | 2002 Ford Taurus

1 Answer

98 taurus no spark what does it need


Hello1 First make sure that the PCM power fuse is OK...It is located in the Inside Passenger fuse box and is fuse # 10 (20A)...If this fuse proves to be good the most probable cause is the Crankshaft Positioning Sensor (CPS)...See diagram #1 for location and diagram #2 for the sensor....



saailer_101.gif




saailer_161.jpg

MOTORCRAFT Part # DY916 ...Cost#35



Guru......Saailer










MOTORCRAFT Part # DY916 Cost $35

Aug 29, 2011 | 1999 Ford Taurus

1 Answer

Looking for location and how to replace the crankshaft sensor on a 98 escort zx2


Buyauotparts is a place where you could replace all car parts with good quality and affordable price. Have a visit at this link to have a better idea. http://www.buyautoparts.com/crankshaft.htm

Mar 30, 2011 | 1998 Ford Escort

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

2 Answers

98 silverado 5.7L camshaft position sensor


ITS ABOVE CRANKSHAFT PULLEY.IT CONNECTS WITH CRANKSHAFT POSITION SENSOR.

Oct 23, 2009 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

Where's the crankshaft position sensor located in 98 plymouth voy


Guessing it's a 6 cyl, 3.0L, but should be located on transaxle housing above vehicle speed sensor.c937fe4.jpg

Aug 31, 2009 | 1998 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...