Question about Volvo V40

Open Question

Volvo V40 2.0 -96 timing gear marks please pictures my Email

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1757 Answers

SOURCE: HOW TO RESET TIMING ON 2000 VOLVO V40

Sorry for the delay.
I am personally going back to answer your unanswered question. I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt/MARK(S) Diagrams that you will need, complete with Instructional and Directional Diagrams.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2000/make/volvo/model/v40/2000_volvo_v40_timing_belt_diagram_marks.htm

Posted on Mar 28, 2010

c17hydro
  • 2984 Answers

SOURCE: timing marks on a 2000 volvo v40 1.9t

Timing belt alignment markings


9c6ff12.gif

Here is all the tech info for removing and replacing....hope this helps you:

4-Cylinder Engine

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Right hand engine cover
    • Cover over the right headlamp
    • Accessory drive belt
    • Front timing cover
    • Servo reservoir
  3. Position Volvo lifting beam 999 5006 or equivalent slightly in front of the front lifting eyelet for the engine. Use Volvo lifting arm 999 5383 or equivalent and Volvo lifting hook 999 5460 or equivalent to raise the front of the engine a few millimeters.
  4. Remove or disconnect the following:
    • Right-hand engine mount
    • Right front wheel
  5. Turn the crankshaft until the markings on the crankshaft and camshaft pulley correspond. Turn the crankshaft a further 1/4 turn clockwise and then back again until the markings correspond. The markings are illustrated. Remove the upper timing cover.
  6. Slacken off the center screw for the belt tensioner slightly.
  7. Turn the tensioner clockwise to 10 o'clock.
  8. Remove or disconnect the following:
    • Air baffles
    • Lower belt cover
    • Timing belt


To install:
  1. Turn all the pulleys listening for bearing noise. Check to see that the contact surfaces are clean and smooth. If the tensioner pulley lever or idler is seized, replace it.
  2. If replacing with a new idler pulley, tighten to 18 ft. lbs. (24 Nm).
  3. If replacing tension pulley, screw into place using the center bolt by hand. Ensure that the tensioner fork is centered over the cylinder block rib. Ensure that the Allen hole on the eccentric is at "10 o'clock".
  4. Install the timing belt in the following order:
    1. Around the crankshaft sprocket
    2. Around the idler pulley
    3. Around the camshaft sprockets
    4. Around the water pump
    5. Onto the belt tensioner
  5. Carefully turn the crankshaft clockwise until the timing belt is tensioned. The belt must be tensioned between the intake camshaft pulley, the idler pulley and the crankshaft
  6. Hold the belt tensioner center screw secure. Turn the belt tensioner eccentric counter-clockwise until the tensioner indicator passes the marked position.
  7. Then turn the eccentric back so that the indicator reaches the marked position in the center of the window and tighten the center bolt to 15 ft. lbs. (20 Nm).
  8. Press the belt to check that the indicator on the tensioner moves easily.
  9. Install or connect the following:
    • Lower belt guard
    • Air baffles
    • Upper timing cover
  10. Turn the crankshaft two turns. Check that the markings on the crankshaft and camshaft pulley correspond.
NOTE Check that the indicator on the belt tensioner is within the marked area.

  1. Install or connect the following:
    • Lower timing cover
    • Front timing cover and tighten to 9 ft. lbs. (12 Nm)
    • Accessory drive belt
    • Engine mount and tighten to 49 ft. lbs. (67 Nm)
    • Servo reservoir. Tighten bolts to 37 ft. lbs. (50 Nm).
    • Front wheel
    • Right hand engine cover
    • Cover over the right headlamp
    • Negative battery cable

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are my marks on crankshaft for a 2001 Volvo s40


what marks are you looking for the timing marks if so they are on the timing gear

Nov 15, 2015 | Volvo Cars & Trucks

1 Answer

Timeing marks


The timing marks are on the gears under the cover once you find them on the gears remove the side cover I think its 12mm bolt put the top one back on and the two notches on the center of the plastic cover are the tdc marks to line with the gears

Mar 06, 2014 | 1998 Volvo S70

2 Answers

I remove the gears from camshafts and didnt mark it


There should be a timing notch, dot, line, or even a different tooth on the gear somewhere to match them up.

Aug 28, 2011 | 2001 Volvo S40

1 Answer

I need cam timing settings for a volvo s40 2006


The timing marks on the cam gears align with the timing marks in the rear timing cover. The timing mark on the crank gear aligns with the timing mark on the oil pump assembly.
The tensioner is set by rotating the tensioner clockwise until the holes in the tabs on the left side of the tensioner are aligned, then tighten the center bolt.

Dec 24, 2010 | 2006 Volvo S40

1 Answer

Timing for a 1991 volvo 740


Hi, this is how to align timing on a 1991 Volvo 740.
There are marks for all three. Cam and Aux shafts have dots on face of outer gear. Cam lines up with mark on rear timing cover(about 1 o'clock). Aux lines up with mark on seal housing (about 3 o'clock) and crank lines up with mark on seal housing (about 12 o'clock).

Take care

Aug 08, 2010 | 1991 Volvo 740

1 Answer

1994 Volvo 940 install timing belt


TAKE FRONT COVER OFF(AFTER REMOVING FAN, BELT S, PULLEY AND FAN SHROUD).THEN REMOVE CRANK SHAFT PULLEY. WHEN COVER IS REMOVED YOU'LL SEE 3 SPROKETS, SUGGEST TO BRING CRANK TO TOP DEAD CENTER UNTIL YOU SEE ALL 3 MARKS FOR THE TIMING BELT. REMOVE BELT/INSTALL NEW AND REVERSE PROCEDURE.

Dec 23, 2008 | 1994 Volvo 940

1 Answer

Timing


Hi,
The 3L 24V straight 6 engine has timing marks on the crankshaft pulley & on the camshaft pulleys. The crankshaft pulley aligns with a mark on the front of the block, the camshafts align with two marks on the plastic cover on the top. The ignition timing, the fuel/air mixture & the valve timing are not adjustable. The 3L engine is known as an "Interference" engine, in other words, if the cam belt breaks or is not set up correctly, the pistons 'meet' the valves, with dire consequences!!!!!

Nov 04, 2008 | 1995 Volvo 960

1 Answer

Timing belt replacement info please


There should be a mark on both the cam gears, and a mark on the crankshaft gear. There are some important steps when you replace the belt on this car. If you make a mistake, you will cause engine damage so make sure you get the information before you do the job. I recommend replacing the tensioner when you replace the belt too. Look for tutorials on some of the Volvo forums.

Bret
RepairPal.com

Jul 30, 2008 | 1999 Volvo S70

1 Answer

I am replacing the timing belt on a 93 volvo 940 with 4 cly single overhesd cam no tubo. Where does the cam's timing mark line up? I don not have a repair manual for this.


I replaced mine on the same car.  I borrowed the NAPA timing belt book to get the timing marks.  There are three that need to be aligned.  I would suggest going to NAPA to buy the belt ($25) and while there, ask to see that book so you can write down the timing marks.  The mark on the crank shaft gear is on the inside of the gear, while the cam gear is on the outside of the gear.  Or, you could just buy the book.  It's still a lot cheaper than paying someone to replace the belt.

Jul 26, 2008 | Volvo 940 Cars & Trucks

4 Answers

Timing marks on volvo s40


the crank has the only mark you have a procedure for the cam gear you should see if the local dealer will print this out for you

Jul 01, 2008 | 2004 Volvo S40

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...