Question about 2007 Mazda B2300

1 Answer

Have a 94 b2300 in which I have replaced the transmission. Im having trouble bleeding the slave cylinder. What is the best way to go about fixing the problem?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mazda Master
  • 8,841 Answers

See recent solution to similar problem: and let me know if you have more questions.

Posted on Sep 14, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 94 d21 Nissan and it sounds like its going into gear but will not pull at all why

If it is a manual transmission,then it could be your slave cylinder.Check your clutch fluid,if low or out then your slave cylinder is leaking and not holding pressure.I have a 85 Nissan 720 4x4 with the 2.4 engine,replaced mine a few times,you can just add fluid and bleed it to get you home.Here's a link on how to replace,you didn't state if you have the 2.4 or 3.0 engine,here's another link on the part.Autozone sells a one man bleeder kit for about 8 bucks,I have one,the cylinder is located on the side of the transmission,easy to replace. Repair Guides Clutch Clutch Release Cylinder AutoZone com Here's a link on bleeding it. Repair Guides Clutch Bleeding The Clutch Hydraulic System AutoZone com It uses brake fluid,the same that's in your brake reservoir. Duralast Clutch Slave Cylinder 12425 Read Reviews on Duralast 12425 Here's the bleeder kit you will need. OEM One man brake bleeder kit 25036 Read 17 Reviews on OEM 25036

Aug 13, 2017 | Nissan Cars & Trucks

1 Answer

Transmission not shifting

If it's a manual transmission,then maybe your clutch slave cylinder is bad,check your clutch fluid reservoir,if empty then it's bad and needs replacing,should have fluid around it.Here's a link to replacing your clutch slave cylinder. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Here's a picture of the part. Clutch Slave Cylinder at AutoZone com Best Clutch Slave Cylinder Parts for... Also check your master cylinder,could be bad.Here's a link to the part. Clutch Master Cylinder at AutoZone com Best Clutch Master Cylinder Parts... Here's how to replace the clutch master cylinder. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE And lets not forget to bleed it,here's a link for that. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE The brakes and clutch share the same reservoir.The end....

Jun 05, 2015 | 2000 Mercury Mystique

1 Answer

How do you fix a slave cylinder on a 2008 Suzuki froenza

if it is inside the transmission then it is best left to the experts unless you have a vehicle lift

Nov 11, 2014 | 2008 Suzuki Forenza

2 Answers

I have 94 Mazda mx-3 for the past month or so I've been having problems with my clutch and I notice a big wet stain on the floor mat and carpet I assume its the master cylinder or slave cylinder but I am...

It's leaking on the driver's side? That would be the master cylinder bolted onto the firewall. You will have to replace with a new or remanufactured clutch master cylinder. When the seals go out, the whole unit must be rebuilt. The store will give you a discount if you bring in your old one for exchange.
The clutch slave cylinder will be down on the transmission bell housing. Follow the small steel line from the master cylinder. It goes right to the slave cylinder.
Pretty easy to change out the master cylinder. Remove the steel line, unbolt unit from the firewall, then under the dash, there's a rod from the clutch pedal to the master cylinder. Just undo the retaining clip or pin holding the rod to the pedal. When the new unit is installed and filled with fluid, then you get to learn how to bleed the hydraulic clutch at the slave cylinder-the fun never stops.

Oct 31, 2013 | Cars & Trucks

1 Answer

I have a 1996 Isuzu Hombre. I have had to bleed the clutch a few times lately. Today something gave in and I lost all pressure. No fluid leaking from slave cylinder area but the reservior was empty. There...

Hello buiskit: My name is Roger and I will help you. If the fluid runs down the firewall or leaks down on the floor board or on your foot. The problem should be the clutch master cylinder. However should the fluid leak at the bell housing area.Then the problem is the slave cylinder. To replace the slave cylinder you will need to pull the transmission in order to replace the slave cylinder. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Jul 22, 2011 | Isuzu Hombre Cars & Trucks

1 Answer

1994 chevy manualtranual transmission what is this easy an quick fix for leeking slave cylinder

easy quick fix is to buy another slave and install it, then bleed the system. to repair a slave cylinder costs more than to buy a new slave cylinder.

Jun 06, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

2001 mercury cougar, master cylinder ran dry because slave cylinder below is leaking at the firewall. I filled the master cylinder and tried bleeding the clutch at the transmission until fluid stream...

No, you don't need to replace the clutch itself.
Don't be surprised if the slave cylinder replacement doesn't fix it.
Could be the master cylinder.

Sep 12, 2010 | 2001 Mercury Cougar

1 Answer

Where is the clutch bleed valve? Hyundai excel '94 i think

It should be on the slave cylinder on the transmission. Don't forget to bleed the clutch master cylinder as well. To do this I believe that you will have to crack the line loose on it while someone or something holds the clutch pedal down.

Dec 12, 2009 | 1994 Hyundai Excel

1 Answer

Clutch still won't come up off of floor after replacing both master and slave cylinder for the clutch on 94 passsat

Try unbolting the slave from the bellhousing, leave the fluid line attached. Bleed the slave, then bolt it back on. Make sure that when you are bleeding it, hold the slave so the bleeder is up.

Apr 17, 2009 | 1994 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides