Question about Volkswagen Eurovan
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Sep 19, 2013 | 1996 Saturn SL
Feb 17, 2012 | Nissan Cars & Trucks
May 17, 2011 | 2000 Volkswagen Golf
Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.
Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.
B2500 4 Cylinder
Torque sequence: --------- ' 10 6 2 4 8
' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51
Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final
tighten all bolts an additional 90 to 100 degrees recheck final
torque in sequence *** CAUTION ***engine uses Torque To Yield head
bolts (TTY) that permanently stretch during the initial installation.
New head bolts must be used when cylinder head is replaced or
re-installed to obtain proper torque.
B3000 3.0 6 Cylinder
Torque sequence ---------- ' 6 4 2 8 '
' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen
in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque
to 73 Ft/Lbs
B4000 4.0 6 Cylinder
Torque sequence --------- ' 5 1 3 7 ' '
' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in
sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs
Step 3: turn cylinder head bolts in sequence an additional 90-degrees
recheck final torque in sequence *** CAUTION ***engine uses Torque To
Yield head bolts (TTY) that permanently stretch during the initial
installation. New head bolts must be used when cylinder head is
replaced or re-installed to obtain proper torque.
Good luck with this job!
Feb 06, 2011 | 1998 Mazda Pickup
Jan 22, 2011 | Audi A3 Cars & Trucks
Fig.: Cylinder head torque sequence - 6 -cylinder engine
Cylinder head torquing should proceed in three steps and in the
prescribed order. Tighten them first to 50-55 ft. lbs. (65-71 Nm), then
give them a second tightening to 60-65 ft. lbs. (78-84 Nm). The final
step is to 70-75 ft. lbs. (91-97 Nm), at which they should remain
Six IN V - 6V
Fig.: Cylinder head bolt torque sequence - 6 -cylinder engine
Tighten the head, according to the illustrated sequence in three progressive steps. Tighten the bolts to 50-55 ft. lbs. (68-74 Nm), then 60-65 ft. lbs. (81-88 Nm) and finally to 75 ft. lbs. (102 Nm).
Hope this helps (remember to rate and commene this answer).
Jan 19, 2011 | 1985 Ford LTD
Fig. Cylinder head bolt torque sequence-3.8L engine
Fig. Tighten the cylinder head bolts using the following sequence-31L and 3.4L engines
Dec 16, 2010 | 2002 Pontiac Grand Prix
May 17, 2010 | 1997 Ford F150 Regular Cab
Mar 06, 2010 | 2001 Jeep Cherokee
Sep 18, 2009 | 2000 Ford Focus
24 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: