Question about Chevrolet Silverado 1500

1 Answer

What is involved in rebuilding a complete front end of a 2000 chevy truck

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 864 Answers

Alot is involved bushings and bearings and it will all require a bit of tools about 300$ worth of tools to get started. Need a torque wrench and you will need to align the front end. If its a 4x4 then it will be even more work. If you need specifics please give me the make/model and i can go from there. thanks, Midwest-tek

Posted on Sep 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Elantra GLS with PO 732 and PO 734 codes. Any hope of a repair without a complete tranny rebuild?


2nd and 4th gear ratio codes. No matter the cause, the transmission has to be pulled. Low end at a garage is $1000, top end $2500+.

Mar 05, 2015 | 2000 Hyundai Elantra GLS

1 Answer

What does the cv axle seal on 2000 chevy blazer


Four posts? Really? Buy a cheap shop manual, as the procedure has some hazards and is too involved for someone to spell it all out here.

Sep 30, 2014 | 2000 Chevrolet Blazer

1 Answer

Rebuild chevy tahoe's transmission


If you have the experience you can remove the transmission and rebuild it or you can take it to a trans tech and get an estmate for the rebuild > after the estimate you can call some bone yards and see how much they would want for a used transmission with a warranty> you can also go online and get a price for a bebuilt with a warranty.

Mar 23, 2012 | 2000 Chevrolet Tahoe

1 Answer

I hav a 2000 chevy 4x4 four door when i accelerate the rear end makes a loud banging noise took it to a mecanic they said it was the pumpkin...wnatever that is....please help wat is it and an estimate on...


Pumpkin refers to the rear end and the gears it contains, depending on the damage and what all is involved inside of it damage wise, its hard to give you a cost for the repair

Jun 22, 2011 | 2000 Chevrolet Blazer

1 Answer

Looking to rebuild the entire front end of my 1992 chevy 2500 5.7L 4X4 Please list all the parts needed for the front end....


http://www.compnine.com try this web site they have very detail break down picture of the front end of your truck build your model of your truck and look in group number 6.000 front axle front suspension - steering

Mar 04, 2011 | 1992 Chevrolet C/K 2500

2 Answers

I have 96 chevy silverado extended cab with a vibrationfrom the differential. I found a 2000 gmc Envoy rear end 5 lug. will this bolt up?


Most vibrations are driveshaft being bent,worn u-joint,in need of balance,shocks,wheels,tires and more.I will bet ,swapping the complete rear axle will not change a thing. If it is lifted, you should know your in for problems. If not, and all else fails,strip the rear housing and go through it. The one you swap, may be more worn than yours and not even a good core to rebuild.

Feb 08, 2010 | 1997 GMC Jimmy

1 Answer

My engine make a loud noise like metal hitting metal and it gets louder as i rev.. or drive and its got worse


it knackerd......check the oil level but at this stage it sounds like a big end or main bearing is gone and this involves a major rebuild or replacement engine

Nov 09, 2009 | 2000 Volvo S80

1 Answer

Rebuild the front end


Nope.... best solution is find another Elantra and take the front end apart for comparison.

Oct 12, 2009 | 2000 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...