Question about Ford Laser

1 Answer

Water pump installation diagrams. - Laser Ford Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,984 Answers

Sure! What type of vehicle are we talking about here?

Posted on Sep 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for a diagram of waterpump on a 1999 cadillac deville concours 4.6 liter


0996b43f80208ea8-tv1fhtz0qus1mygxrqn3k2su-5-0.gif

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the coolant.
  3. Remove or disconnect the following:

    Negative battery cable
Upper fill panel, if equipped
AIR injection control valve, if equipped
Air cleaner
Oil level indicator tube nut, if necessary
Water pump belt cover
Water pump drive beltLower radiator hose
Thermostat bypass hose from the coolant inlet housing
Water pump cover

Remove the water pump by rotating it clockwise using special Tool J 38816-1A (water pump remover/installer).
To install:
Install the water pump with a new O-ring, by turning it counterclockwise using the special tool, until it stops. Torque the water pump to 73 ft. lbs. (100 Nm).

Install or connect the following:

Water pump cover. Torque the bolts to 89 inch lbs. (10 Nm).
Lower radiator hose
Thermostat bypass hose to the coolant inlet housing
Water pump drive belt
Water pump belt cover
Oil level indicator tube nut, if necessary
Air cleaner
AIR injection control valve, if equipped
Upper fill panel, if equipped
Negative battery cable

  • Refill and bleed the cooling system.

  • Run the engine and check for leaks.
  • Oct 04, 2017 | Cadillac Cars & Trucks

    1 Answer

    1.6 focus water pump belt diagram


    This belt is the camshaft drive belt (drives the water pump as well), and you must take care to install it correctly or you can seriously damage the engine, Follow the video instructions below. How to replace water pump timing belt on Ford Focus

    Nov 01, 2016 | Ford Focus Cars & Trucks

    2 Answers

    Removing water pump v6 engine


    drain the coolant first. remove the serpentine belt. heres a pic of the hardware to it. hope this helpsonetufshoppe_46.gif

    Jan 25, 2011 | 1997 Buick LeSabre

    1 Answer

    WATER PUMP REPLACE DIAGRAM


    1. Step 1 Drain the antifreeze from cooling system. Remove belt from water pump. Examine and see if you have to remove anything else to get out the water pump. If so make a diagram of everything you are removing so you can put it back together.
    2. Step 2 Remove the hoses from the water pump. Find all bolts holding the water pump in . Loosen each one a little bit. After all are lose you can then remove them. Remove water pump. Put new gasket on and install new water pump. Hook up hoses to water pump. Look at your diagram and replace everything you had to remove earlier. Put the belt back on.
    3. Step 3 Shut the drain on system and refill cooling system. Make sure you use the antifreeze that is designed for system. Run engine for a couple of minutes. Check for leaks and check coolant level. Add if necessary. If there is no leaks you are ready to go.

    Jun 04, 2010 | 2001 Mazda MPV

    1 Answer

    Where can i find a diagram of the 1996 mercury villager water pump placement


    I can sell you a shop manual ans wiring book for $25 plus postage or you can go to our website.

    http://groups.yahoo.com/group/villagerquest/

    1. Drain the cooling system. Refer to Section 03-03 for the procedure.
    1. Disconnect the battery ground cable (14301).
    1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures.
    1. Raise and support the vehicle.
    1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.




    1. Remove the water pump pulley from the water pump (8501).
    1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
    1. Remove the five lower engine front cover bolts and the lower engine front cover (6019).




    1. NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation.

      Remove the six water pump bolts.




    1. Remove the water pump.
    Installation
    1. NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material.

      Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block.




    1. NOTE: Refer to the note made during removal for the location of the stud/bolt.

      Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft).
    1. Position the water pump pulley on the water pump and install the four water pump pulley bolts.
    1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
    1. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
    1. Install the crankshaft pulley. Refer to the procedure in this section.
    1. Lower the vehicle.
    1. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures.
    1. Connect the battery ground cable.
    1. Fill the cooling system. Refer to Section 03-03 for the procedure.
    1. Start the engine (6007) and check for leaks.

    Apr 26, 2010 | 1996 Mercury Villager

    1 Answer

    2002 ford taurus wtaer pump


    Removal & Installation 3.0L (2V) To Remove:
    1. Drain the engine cooling system.
    2. Loosen the water pump pulley.
    3. Remove the bolt and the nut and position the roll restrictor bracket out of the way.
    4. Remove the accessory drive belt.
    5. Remove the generator.
    6. Remove the bolt and the accessory drive belt tensioner.
    7. Remove the nut, the bolt and the support bracket.
    8. Remove the bolts and the water pump pulley.
    9. Disconnect the water pump inlet hose and the crankshaft position sensor electrical connector.
    10. Remove the bolts and the water pump, and clean the sealing surfaces
    To Install:
    1. Install the water pump. Tighten bolts in the sequence shown:
      1. Tighten numbers 1-7 to 18 ft.-lbs. (25 Nm)
      2. Tighten numbers 8-12 to 89 in.-lbs. (10 Nm)
      3. Connect the crankshaft position sensor electrical connector and the water pump inlet hose
      4. Install the support bracket.
      5. Install the accessory drive shaft tensioner.
      6. Install the generator.
      7. Install the roll restrictor bracket, bolt and the nut.
      8. Install the water pump pulley.
      9. Install the accessory drive belt.
      10. Connect the battery ground cable.
      11. Fill the engine cooling system.

    9de9feb.gif
    Water pump bolt torque sequence (3.0L (2V) engine)

    Jul 04, 2009 | 2002 Ford Taurus

    1 Answer

    Water pump installation


    take it off and put the new one on the same way. get new gaskets

    Feb 24, 2009 | 1988 Ford F 150

    2 Answers

    Water pump assembly and power steerin pump brackets


    need to know year? engine size?what accesories equipped? a/c power steer smog pump etc.

    Aug 26, 2008 | 1989 Dodge Ramcharger

    1 Answer

    Water pump


    you can buy some diagrams at alldata.com . and yes all belts must go. goodluck

    Aug 01, 2008 | 1997 Dodge Intrepid

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    64 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    fordexpert

    Level 3 Expert

    5546 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...