Question about Chrysler Concorde

1 Answer

My 2000 Chrysler Concorde has an electrical problem: When you turn it on, the windows don't open, the A/C doesn't work and the "air bag" light comes on on the dash. Could this just be a fuse problem and, if so, where are the fuses in the engine? Could this be an electrical wiring problem that controls those three things? And, if so, how can a get a wiring schematics? It is too hot here in Florida to ride with no A/C and the windows up! Thank you so much, Judy

Posted by on

  • judithnaomi Sep 13, 2010

    I'm sure it was helpful although I don't understand much
    about cars. My son got it working again, so we know
    it's electrical. But we can't get it worked on if it's okay
    when we take it in, he says.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 6,826 Answers

Check the fuses for the respective circuits.

The air bag light goes on when the module or air bag assembly needs to be replaced, or wiring to the sensors is bad or the sensors in the bumper are bad.

Fuses are located under the dash or under the hood.

I understand that it's too hot in FL to run around with the windows up and the A/C broken.

Actually, if the fuse associated with the air bag was bad, then it wouldn't light up.

To get schematics, try Alldata.com, which is based on Chilton manuals, but you can download the information if you pay them a fee.

---
Power Distribution Center (PDC) All of the electrical current distributed throughout this vehicle is directed through the standard equipment Power Distribution Center (PDC). The molded plastic PDC housing is located in the left front corner of the engine compartment, just in front of the coolant reservoir bottle. The PDC housing has a molded plastic cover. The PDC cover is easily removed for service access and has a convenient fuse and relay layout label affixed to the inside surface of the cover to ensure proper component identification. The PDC housing is secured in the engine compartment by one screw to the rear of the PDC and two clips on the front side. A small molded plastic protective cover on the front right side of the engine compartment is unsnapped to access the battery/generator cable input connection studs. All of the PDC outputs are through the integral engine compartment wire harness, which exits from the front of the PDC housing.
Power Distribution Center (PDC) My 2000 Chrysler Concorde has - dod_intrpd_pdc.gif

Power Distribution Center (PDC) Fuse Location

Power Distribution Center (PDC) Fuse Legend dod_intrpd_pdc_fuse_lgnd.gif

prev.gif next.gif

Posted on Sep 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Windows, air bag, blower motor and turn signals stop working until you hit the steering wheel or adjust the tilt


Sounds like the wires are broken in the steering coulmn. They can cause problems on other circuits because they don't supply voltage to everything as needed. Care should be taken working on this as air bag wiring also goes up that coulmn. ( Its bright yellow harness)

May 21, 2015 | 2002 Chrysler Concorde

1 Answer

Car horn doesn't work, airbag light on, but car alarm works


The problem is likely with the clockspring in the steering column. The wiring for the horn button and the driver's air bag go through the clockspring. If you want to fix it yourself, I can probably find the procedure for you, but this is really a job for a professional auto electrician.

Aug 21, 2017 | 2003 Chrysler Concorde

1 Answer

My 2000 Concorde turn signals don't work


Do your flashers work? If not it may be the flasher unit is bad. It is located under the dash on the drivers side on or near the fuse box. If the flashers work you may have a problem with the turn signal lever or the wiring connected to it.

Sep 11, 2012 | 2000 Chrysler Concorde

1 Answer

2000 chrysler concorde turn signal/hazards don't work fuses good changed multifunction switch still no go whats next?


I am having the same problem with my 1999 chrysler concorde amoung other problems. But they will work at times and then they will just stop for no reason. Have you found any solutions yet?

Aug 24, 2011 | 2000 Chrysler Concorde

1 Answer

How do you change the brake light on the back window on a 2000 chrysler concorde


  1. Release decklid latch and open decklid.
  2. From under rear shelf panel, disconnect the lamp socket from the CHMSL housing.
  3. Remove bulb from the socket.
INSTALLATION
  1. Install the bulb into the socket.
  2. Install socket into CHMSL housing.
  3. Verify CHMSL operation.

Apr 19, 2011 | 2000 Chrysler Concorde

1 Answer

Why would the air bag light on dash go on?


either there is a problem or the 10 year service date is due

Apr 15, 2010 | 2000 Chrysler Concorde

2 Answers

Air conditioner blows hot air inadvertantly.


possibl ac compressor clutch problem,cooling fan at rad not working so ac goes into high press mode and turns off(so it doesn,t blow system apart,built in safety)not enough r134 in system(low charge)

Sep 19, 2009 | 1997 Chrysler Concorde

1 Answer

99 Chrysler Concorde electrical problem


probably a relay. relays control switching of power from one compound circuit to another. because you have multiple circuits that are not working, this sounds likely. get a wiring schematic and find out which relay controls that system, then try replacing it.

Jun 18, 2009 | 1999 Chrysler Concorde

1 Answer

94 Concorde electrical


I have a similar problem with my 94 concorde... and was advised the on board computer was in need of replacement. Further research led to pulling the computer and cleaning the ground connection to the chassis. It will sometimes leak under the computer and corrode, and compromise the ground, which in turn will cause faulty "code" readings and the engine control light to come on.

May 24, 2008 | 1994 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...