Question about 2000 Chevrolet Silverado 1500

Open Question

Is there a hush panel for the 2000 Chevrolet 1500 regular cab. I had a temperature accuator replaced and it appears that there is some panels missing under the dash. The Tech says only the extended cab had a hush panel. Can I get a picture of the regular cab under dash, passenger side?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

CMV9
  • 594 Answers

SOURCE: 2004 Chevrolet Silverado Extended Cab

jack the truck up and take the passangers tire off. look behind the rotor you should see 2 bolts holding the caliber on to the rotor. loosen those and take them out. from there you should be able pull up on the caliber this will take the caliber and pads off together. take the pads out of the caliber and install the new ones .

BECAREFUL not to twist or bend the caliber to much or you will bend the brake line.....

once you have installed the new brake pads in the caliber. put the caliber back on the rotor. if they will not fit release the bleader valve to release the pressure. than you should be able to slid the caliber back onto the rotor. once you have done that close the bleader valve. reinstall the 2 bolts to hold the caliber in place. put your tie back one. Follow these steps for the other side.

now once that is done. you might want to blead the front breaks.
what you do is have someone help you. fill the brake resiviour with brake fliud. than start your truck.
Have someone in the cab to press the brake. What you want to do is turn the wheel so you can get to the bleader valve. once you can get to it open it up. have the person in the cab other truck press the brake until you see a steady flow of brake fluid coming out of the caliber. once you see that have the pseron press the brake once more and hold it to the floor.
close the bleader valve.

now do the same thing on the other side. But, make sure you check your resivour fluid first.
This is to make sure you don't have any air in the lines. after you are done with both side put it in gear and hit the brake make sure you stop......... If that works go about half the block down and hit the brake again to make sure you stop......
once you have done that and are comfortable with the way the truck stops than ou are good to go and now know how to change the brakes for future refrence..... be aware the back brakes are diffrent.........

let me know when you are ready for the back brakes.
do not blead the front ones if ou intend to do the back brakes afterwarwords......

if you are only doing the front brakes you must blead the the passanger side first......... if you do not have the bolts holding your caliber on than you will have a pin the you will take a hammer to and knock it out that will release them....

Posted on Aug 01, 2008

Ajkill
  • 2035 Answers

SOURCE: Replace passenger mirror

  1. Remove the door inside handle as follows:
    1. Remove the screw and slide the handle forward.
    2. Disconnect the handle from the control link and remove the handle.
  2. Remove the door trim as follows:
    1. Remove the 2 caps and 2 screws.
    2. Using a screwdriver, remove the door trim upward then disconnect the connectors.
    3. Using a screwdriver, pry the forward of armrest panel and remove the panel.
    4. Remove the 2 screws and tweeter speaker.
    5. Disconnect the connector, remove the 5 screws and speaker.
    6. Disconnect the wire harness and remove the 2 grommets and service hole cover.
  3. Remove the cover and disconnect the power mirror connector.
  4. Remove the 3 nuts and outer rear view mirror.
To install:
  1. Installation is the reverse of the removal procedure.
  2. Tighten the mirror nuts to 8 Nm (71 inch lbs.).

Good luck...

Posted on Nov 11, 2008

emissionwiz
  • 75797 Answers

SOURCE: 1997 Dodge Ram 1500 transmission will a 1996 interchange

No, the frame is different.

Posted on Nov 30, 2008

  • 14036 Answers

SOURCE: Replace window motor assembly 2001 Chev 1500 extended cab truck

you can order it at some dealer ships . it cost about 150.00 dollars or more.

Posted on Apr 02, 2009

  • 206 Answers

SOURCE: check engine lite on 98 chevy k1500 code is gas

Check the gas cap is sceruely fastened, check for leaks in the filler tube for gas tank, and check for leaks in the hoses/tubes to the evaporative canister.

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I find the blower motor resister


Look up by the blower motor on the passenger side compartment of the vehicle. You will have to remove the hush panel and then you should be able to find it near the blower housing area. They usually are a flat type connector with 4-5 wires on them.

Jan 07, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

How many hvac blend door actuators are there in a 2002 chevy silver ado and where are they located. I tried to purchase the part and it gave me an option for upper and bottom actuators. I need to know...


I'm having the same problem with my 00 GMC Sierra. If you do NOT have dual zone climate control, it's just to the passenger side of the transmission hump under the hush panel underneath the dash. 3 screws take off the hush panel, two take off the actuator. One screw on the hush panel is a pain in the **** to get out. I'm still trying to figure out if the "upper" or "lower" is the proper fit for it. If you have dual zone, then one is under the passenger side, and the other is under the driver side. Hope this helps!

Sep 16, 2010 | 2002 Chevrolet Silverado 1500

1 Answer

How to install ac mode actuator on 2003 gmc sierra


prev.gif next.gif Air Door Actuators Removal & Installation Air Temperature Actuator Air Temperature Actuator Replacement gm-10-00-559.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel hush panel.
  2. Disconnect the connector from the air temperature actuator.
  3. Remove the air temperature actuator mounting screws.
  4. Remove the actuator from the HVAC assembly.
To Install:
  1. Position the air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Install the electrical connect to the air temperature actuator.
  4. Install the instrument panel hush panel.
Right Side Air Temperature Actuator (2003-2007) Right Air Temperature Actuator Replacement gm-10-00-560.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel carrier.
  2. Disconnect the connector from the right air temperature actuator.
  3. Remove the actuator mounting screws.
  4. Remove the right air temperature actuator.
To Install:
  1. Position the right air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Connect the electrical connector to the actuator.
  4. Install the I/P carrier.
  5. Calibrate the actuator.
Left Side Air Temperature Actuator (2003-2007) Left Air Temperature Actuator Replacement gm-10-00-561.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the I/P insulator panel.
  2. Disconnect the connector from the left air temperature actuator.
  3. Remove the actuator mounting screws.
  4. Remove the left air temperature actuator.
To Install:
  1. Position the left air temperature actuator on the HVAC assembly.
  2. Install the actuator mounting screws.
  3. Connect the electrical connector to the actuator.
  4. Install the I/P insulator panel.
  5. Calibrate the actuator.
Mode Actuator Mode Actuator Replacement gm-10-00-562.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the floor air outlet from the floor duct.
  2. Remove the center console and center console duct (if equipped).
  3. Disconnect the electrical connection at the mode actuator.
  4. Remove the mode actuator mounting screws from the HVAC module.
  5. Remove the mode actuator with the actuator cam attached.
To Install:
  1. Position the mode actuator with the actuator cam to the HVAC module.
    • Align the heater/defroster valve lever with the cam slot
    • Align the A/C valve lever with the cam
  2. Install the mode actuator mounting screws.
  3. Connect the mode actuator electrical connection.
  4. Install the center console duct and the center console (if equipped).
  5. Install the floor air outlet duct extension to the floor air duct.
  6. Calibrate the actuator.
Air Inlet Actuator/Recirculation Actuator Delphi Recirculation Actuator Replacement (Delphi) gm-10-00-564.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the instrument panel upper trim panel.
  2. Remove the instrument panel lower trim panel and glove box assembly.
  3. Remove the passenger side air bag.
  4. Disconnect the connector from the recirculation actuator.
  5. Remove the recirculation actuator mounting screws.
  6. Remove the recirculation actuator from the HVAC assembly.
To Install:
  1. Position the recirculation actuator on the HVAC assembly.
  2. Install the recirculation actuator mounting screws.
  3. Connect the electrical connector to the recirculation actuator.
  4. Install the passenger side air bag.
  5. Install the instrument panel lower trim panel and the glove box assembly.
  6. Install the instrument panel upper trim panel.
  7. Calibrate the actuator.
Visteon Recirculation Actuator Replacement (Visteon) gm-10-00-566.gif

To Remove:
CAUTION
Do not apply power to the actuator when it is removed from the HVAC module.
  1. Remove the HVAC module assembly.
  2. Remove the evaporator core cover from the HVAC module.
  3. Remove the recirculation actuator from the HVAC module assembly.
To Install:
  1. Position the recirculation actuator on the HVAC assembly.
  2. Install the recirculation actuator mounting screws.
  3. Install the evaporator core cover to the HVAC module.
  4. Install the HVAC module assembly.
  5. Calibrate the actuator.
prev.gif next.gif

Jul 09, 2010 | 2000 GMC New Sierra 1500

1 Answer

Remove & replace heater core on 1997 blazer


Disable air bag system. See AIR BAG RESTRAINT SYSTE
EQUIPMENT section.

Remove instrument cluster trim plate. Move tilt ste
and move automatic transmission gear selector to lo
w (if equipped).

Remove left underdash hush panel.
Keyless Entry (RKE) module connectors. Remove cente
release cable from instrument panel. Disconnect par
k brake cable from ratchet mechanism.

Remove right underdash hush panel. Remove lighter a
light. Remove knee bolster. Partially pull A/C-heat
back of A/C-heater control panel and radio.

Remove 4 steering column retaining bolts and lower
grilles. Remove 9 instrument panel support bolts.

Mar 18, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

Heater blows warm air


First thing, check coolant level. MAKE SURE THAT COOLING SYSTEM IS COLD BEFORE REMOVING RADIATOR CAP!!! If the coolant is full, then you need to go inside and check under the dash[you may need to remove lower hush panels] find the control cable and crank arm for the temperature control. Move the temperature control lever on the dash control to confirm and make sure the arm moves.

Nov 01, 2009 | 1998 Chevrolet Blazer

1 Answer

Replace window motor assembly 2001 Chev 1500 extended cab truck


you can order it at some dealer ships . it cost about 150.00 dollars or more.

Jan 12, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

2000 chevy 1500 truck stuck in 4-wheel drive


the shifter accuator or the wires going to it on the transfercase..gl

Jan 06, 2009 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...