Question about 2004 Volvo XC90

3 Answers

Replace tail light bulb

How to you replace tail light bulb

Posted by on

  • Rayh19 Mar 28, 2009

    Even after I removed the 2 hex bolts, the light housing would bot come out. It was just slacker, but would not budge. Any idea whats the cause?

  • Anonymous May 25, 2009

    Same brake light replacement problem. Removed two very long 10 mm bolts, but tailight unit still will not budge.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 291 Answers

1. open tailgate. 2. remove corner floor piece by lifting. 3. remove corner side panel. pull out from tab on bottom. 4. remove two hex bolts(#10) to release light housing. they look like large allen wrenches. 5. replace bulb(s) and refasten again.

Posted on May 15, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How can i change thetail light of anissan versa 07

Posted on Sep 26, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Tug really hard there may be some dirt that has gotten the taillight stuck.

Posted on Oct 29, 2010

5 Suggested Answers

eitan
  • 291 Answers

SOURCE: replace tail light bulb

The process for changing the tail light bulbs for a 2002 New Beetle in my case a TDI is relatively simple. To remove the lense and gain access to the bulbs you first need to release the lense holder from inside the trunk by completely unscrewing the large plastic wing nut that is under a round plastic panel that's located almost directly behind the rear brake light lense. To gain access to the plastic wing nut remove the round panel by gently prying it off. After this is done you release the lense by using something flat like a dinner table knife to pry and release the clip that holds the lense in place. Locating the clip: The rear fender has two seams that end at the light lense, the inboard seam (the one closest to the hatch)is where you want to insert the table knife to pry the metal clip that holds the lens in place. Gently and carefully insert the knife blade directly at the seam and pry upward to release the lense. Once the clip releases pull the lens the rest of the way and remove the bulbs by turning the bulb holder sockets couter-clockwise. After this is done remove bulbs by slightly pushing down on the bulb and turning it counter-clockwise. The reinstall is reverse of the removal the procedure.When re-installing take care to clock the lense where the metal clip and the lense protrusions end up in the same position as before. Note: you may need to assist sliding the lens retaining clip in with the knife when reinstalling! Good luck

Posted on May 15, 2008

  • 1 Answer

SOURCE: replace tail light bulb

open hatch, look for two screws, remove , push tail light gently back and forth to release from clips pull light assembly out , twist bulb socket to remove from housing, replace bulb.

Posted on Sep 19, 2008

emissionwiz
  • 60792 Answers

SOURCE: Need to replace tail light bulb on 1996 Buick Century

Inside the trunk, under the carpet behind the tail lights will be a whole bunch of small plastic nuts, running from one side of the car to the other. Take all of these plastic nuts off, and the whole tail light assembly will come off in one large piece. Find the bulb you need to replace, and reassemble

Posted on Apr 06, 2009

jaysonemanme
  • 500 Answers

SOURCE: 2002 Ford Taurus Driver Side tail light bulb replacement

open the trunk.
pull back the cover on the side you need to change, there are usually 3 black plastic nut you have to remove before doing this.
after the trunk interior cover is pulled off there are 3 nuts, 11mm wrench or socket will take them off. pull the taillight assembly out and twist the socket out containing the bulb that is blown. the bulb just pulls out of the socket. while the bulb is out you should inspect the socket for corrosion, it wont hurt to clean it up and put some die electric grease in there

Posted on May 19, 2009

  • 146 Answers

SOURCE: NEED TO REPLACE A TAIL LIGHT BULB IN A 2005 CHEVROLET IMPALA

and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tail lights dont turn on


1. Replace your car tail light. You will need working gloves to protect your hand during the process. Of course you will also need a screwdriver, cleaning cloth, wire brush, and a good set of tail light bulbs.

2.Understand that different models of car have different set of tail light covers. Naturally, these covers will require different un-installation procedures. So, determine if you can dismount the cover from the outside or you will have to dismount it from the trunk of the car.

3.Determine how to dismount the tail light cover, carefully detach it from the car. You can use different sets of screwdrivers for this. Be careful not to break the tail lights cover. The important thing is you must be able to expose the bulb in order to extract it.

4.Remove the tail lights cover, unscrew the bulb from its socket. Sometimes you will have to press a little and twist the bulb in order to extract it from the socket.

5.Extract the bulb, bring it to your favorite auto parts and accessories store and find the exact match of your tail light bulb. Be sure to get the correct match because if you use other types of bulb, your tail lights may not work properly.

6.Reinstall the tail light bulb, clean the aluminum casing of the tail light. Wipe the socket and wiring with a dry cloth. You can use wire brush if there are corrosion around the tail light casing.

7.Put the good bulb on the socket. You might still need to apply a little pressure on the socket before you can install it fully.

8.Reinstall the tail light bulb, replace the cover of the tail lights and secure it tightly.

9.Test to make sure your new tail lights are working. Start the engine and apply the brakes. You can ask someone to see if the tail lights are really working.

resource: http://www.wikihow.com/Fix-Car-Tail-Lights

Aug 27, 2012 | 1998 Buick LeSabre

1 Answer

How to install evo 5 tail lights


check see tail light lens has 4 screws holding it in place.if so remove 4 screws then remove rear tail light lens then replace tail light bulbs.if you have trouble replacing tail light bulbs the auto parts store sales person will help you free of charge and help you replace bulbs.i have seen auto parts stores sales person help people replace batteries,windshield wiper blades and light bulbs in vechicle if you have trouble fixin it your self.

Feb 06, 2012 | 1998 Mitsubishi Lancer

1 Answer

How do i replace the tail light bulb


Open the trunk, and pull back the carpet behind the tail light assembly-- you should see 3 different sets of wires going into the back of the tail light assembly. Pick the one you need to replace, and give it about a quarter turn counter-clockwise, and the bulb, harness, and wire can be pulled out of the tail light. Replace the burned out bulb in the socket, and reinstall the bulb just as you removed it.
If you have difficulty getting to the wiring harnesses to dislodge them from the tail light assembly, you can remove the tail light entirely by unscrewing the black plastic wingnuts that hold the tail light assembly in place. It may take a little bit of effort to get them started, but will allow you to see what you are doing a bit better.

Mar 04, 2011 | 2000 Lincoln Town Car

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

1 Answer

How do i replace the tail light bulb?


to replace the GM tail light bulb, you will drop down the tail gate and you will notice 2 screws on the tail light assembly, you will remove those 2 screws with the proper screw driver, once you do that the whole tail light assembly will come off, then you will see onother 2 screws holding the light panel to the tail light assembly, or brackets holding the light panel to the tail light assembly remove either or and you will have access to the three bulbs on that light panel, replace the burnt one and follow the same intrunctions to put back.

Apr 06, 2010 | 2005 GMC Canyon

1 Answer

NEED TO REPLACE A TAIL LIGHT BULB IN A 2005 CHEVROLET IMPALA


and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

Jun 08, 2009 | 2005 Chevrolet Impala

1 Answer

Need to replace tail light bulb on 1996 Buick Century


Inside the trunk, under the carpet behind the tail lights will be a whole bunch of small plastic nuts, running from one side of the car to the other. Take all of these plastic nuts off, and the whole tail light assembly will come off in one large piece. Find the bulb you need to replace, and reassemble

Apr 06, 2009 | 1996 Buick Century

1 Answer

Replace the tail light bulbs in 2004 infiniti g 35 coup


tail light bulbs are replaced by removing the tail light housings. The housings are accessed by removing the nuts, the nuts are secured behind the inner trunk liner inside the trunk. Remove fasteners holding liner in place, remove 3 nuts for each housing(i believe it's 3 nuts if my memory serves me right), remove housing and replace bulbs

Jan 13, 2009 | 2004 Infiniti G35 Sport Coupe

1 Answer

Hyandia Accent


not sure which top tail light you mean? do you wish to replace bulb or actual lamp on the rear screen? this is the high level brake light ! OR do you wish to replace bulb in one of the rear tail lamps offside/nearside ? which ever ? the h/level brake light bulb is accessable for bulb from the rear panel on hatch behind lamp bulb is 16 watt capless push in type

Nov 10, 2008 | 2003 Hyundai Accent

2 Answers

Replace tail light bulb


open hatch, look for two screws, remove , push tail light gently back and forth to release from clips pull light assembly out , twist bulb socket to remove from housing, replace bulb.

Aug 20, 2008 | 2005 Kia Sportage

Not finding what you are looking for?
2004 Volvo XC90 Logo

Related Topics:

2,516 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...