Question about 2003 Nissan Maxima

1 Answer

Where exactly is the starter and what is the easiest way to get it out? starter broken

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Nissan Master
  • 8,531 Answers

Please see my tips at and let me know if you have questions.

Posted on Sep 13, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What's the easiest way to change the starter on a

The same way you would change a regular car starter.

Feb 21, 2012 | 1986 Nissan Pickup 4WD 1986

1 Answer

How do you change the starter in a 1999 dodge status 2.4l

My solution may not be exact so dont shoot the messenger. All starters have to engage the flywheel to kick the motor over. Find where the motor meets the transmission bell housing. Either on the front side of the transmission or the backside is where the starter will be.

After you find the starter location: Disconnect battery, find the easiest way to get to the starter (top or bottom of engine bay), remove anything that may make your job harder on you. Now that you have good access to the starter; remove the two or three wires that are attached to the backside of the starter. When all wires are free from the starter, you can now remove the bolts that hold it into the tranny bell housing. Be careful when you take these out cause the starter may fall to the ground or where ever.

Good luck, I hope this helps, happy wrenching

Mar 08, 2011 | 1999 Dodge Stratus

2 Answers

Starter wire

This is the starter solenoid,if it has broken,replace the starter,it will have one on it,and this is the only way to replace it,if this was helpful,please rate,thank you.

Jun 25, 2010 | 1990 Dodge Dakota

1 Answer

How to remove a starter from a 1999 chevy silverado 4x4 pickup

1) Disconnect Negative Cable on Battery
2) Starters on right-side Close to Trans. Bell Housing
3) Remove the 2-Starter Bolts and Shim if it's
if it has shims.
4) Remove the wires off Solenoid: Mark Them:
5) Remove the Heat Gaurd Over top of Starter:
6) Take Starter on Out.

To Re-Install Reverse the Procedure that you Removed the Starter. NOTE: the Shims if there was any are only nessary if the Casting of the Starter is not Exactly or Close to The Original.

Be sure that All the Wires you Took off the Starter Solenoid are put Back on the Exact Same Terminal. And Snug them up .Be careful not to Over Tighten,:
Specs on Bolts Are :
Torque Starter Battery Cable Nut to 90 inch lbs
Torque Smaller ingnition wier nuts to 18 Inch Lbs
Torque the 2- Starter Mounting Bolts to 35 FOOT lbs.
Remember if your Old Starter Had Shims the New one MIGHT need Shims.All Starters Casting are just a Little Different. like by thousands of an inch. So if you have problems you might have to remove or add shims,they come in different sizes. Hope this has helped you,Please let me know how this solution Helped. Thank You: From d_hubbs

Jun 07, 2010 | 1999 Chevrolet C1500

1 Answer


The solenoid is part of the starter they are all one. The easiest way to fix it would be to replace the starter.

Mar 14, 2010 | 1996 Saab 900

3 Answers

Where is the starter motor and is it difficult to change . 2000 olds intrigue

its usually located on the the bottom side of the engine next to the flywheel . if you got the right tools it shoulnt be that hard to replace

Jun 27, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Reaching top starter bolt.....

Easiest way I have done this is by reomving the rubber intake pipe. Then by using a 14mm flex socket with a 6 inch extension. You may also have to remove the starter to give yourself a little bit more room.

Apr 09, 2009 | 1998 Toyota Corolla

1 Answer

How do you remove a starter on a 1986 plymouth reliant k? where is it exactly and what is the easiest way to get to it?

its behind the engine the bolts that hold it in are located in the bellhousing.. depending on the style of engine you have there was a split in that year you may have just two or three bolts through the transmission that hold the starter in or just two bolts and one nut on a stud that you get from the starter side.. also ther is a hanger/ support bolt and bracket on the back of it that can be remove most easily from under the car..

Feb 18, 2009 | 1986 Plymouth Reliant 4 Door

1 Answer


Ebay sells a replacement handle that looks exactly like factory handle but just screws on, it is a very common thing to break, as mine did.

Nov 30, 2008 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
2003 Nissan Maxima Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides