Question about Lincoln Navigator

1 Answer

Rear air suspension will not inflat rear of vehicle sagging sitting on frame front works need diagram of which relay(s) that may not be working. switch under glove box is on.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

All those airbag rear ends die someday and the price to fix them exceeds the value of the car. It is some kind of cruel joke played on folks who expect more than 3 years out of a car. There is a canadian company called strutmasters.com, They can sell you a kit for replacing the whole collection of airbag **** with a real rear suspension which does not deflate. It is not free and I imagine the labor is going to be more than a day. So look up the price of the kit for your car and make a judgment as to how much you are willing to spend. Otherwise sell it for parts.

Posted on Sep 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My air compressor works run for about 20 sec then cut off rear still sagging


Sounds a lot like an Air/Vacuum leak to the rear Shockies..... See a Suspension Specialist....

May 08, 2014 | 2004 Ford Crown Victoria

2 Answers

WHERE IS THE REAR HEIGHT SENSOR ON 2004 LINCOLN NAVIGATOR


Usually between the frame and the rear axles. A lever type device, should be fairly easy to locate. Check that the compressor is building air pressure and storage tank. Air bags not leaking and etc.

Feb 13, 2013 | 2004 Lincoln Navigator

2 Answers

Need help with a 2001 Expedition air suspension problems


I will try to help you. There are just a few things that can be tried for free and sometimes a better Scanner can be hooked up to diagnose the suspension system. The Scanners vary by store among Autozone, Advance, and Oreilys autoparts.

The Relays in the Powerbox could be bad. Register your vehicle on Autozone.com and get free Fusebox layouts and wiring diagrams, which are color coded.

The rear cargo lid and all 4 doorjam switches must be closed in order for the airpump to work. There should be a Master dump(vent) solenoid inside the Drivers front fender ahead of the front tire. When this solenoid corrodes, it can stick in an open position and lock out the airpump.

Inversely, if stuck in the opposite position, it can keep the car raised up.

For the airlines and suspension bags a mix of soapy water in a spray bottle will detect an air leak when sprayed on the lines and suspension bags. This will produce bubbles. But the suspension does need to have air in it for this test to work.

When you do have pressure, remember that these are high pressure lines if you go to disconnect them and protect your eyes.

There are a few parts sites like Carparts or Car-parts.com which deliver Salvaged parts directly to your door via UPS or Fed-Ex. Price comparisions give you a choice of who to buy from and the site has full contact info.

You can get a clue from how the vehicle sits. If back is down or if one side is down, a partial inflation means the pump should still be good.

I hope my solution is helpful.

Aug 13, 2012 | 2001 Ford Expedition

3 Answers

When my envoy sits overnight my rearend drops down


There has been a service bulletin for that type of concern. Here is what it states.









Suspension - Rear Suspension Is Low/Sagging/Uneven

Notes




ENGINEERING INFORMATION

Bulletin No.: 06-03-09-006B

Date: December 15, 2008
Subject:
EI06006 - Rear Suspension Uneven, Sagging, Low (Recalibrate Air Spring Sensor)

Models:
2006-2007 Buick Rainier
2006-2007 Chevrolet TrailBlazer SS
2006-2007 GMC Envoy, Envoy XL
2006-2007 Saab 9-7X


with Suspension Pkg - Rear Load Leveling (RPO G67)

Supercede:

This bulletin is being revised to update the labor operation in the warranty information. Please discard Corporate Bulletin Number 06-03-09-006A (Section 03 - Suspension).

Condition

Some customers may comment on the rear suspension being uneven or sagging.

Correction

DO NOT REPLACE THE COMPRESSOR.

Based on technician feedback, engineering has determined that the customer's concern can be corrected by recalibrating the air spring sensor. Refer to the Trim Height Uneven or Low diagnostics and Air Spring Sensor Calibration procedure found in SI.

Nov 29, 2011 | 2004 GMC Envoy

1 Answer

My 1992 tornado trofeo back is lower then the front


Check your rear suspension. Load-leveling air suspension struts could be bad or leaking. Air suspension compressor could be inoperative. Air suspension compressor relay could be bad. Air lines from compressor to struts could be leaking, from cuts, cracks, or having rubbed through against the frame. Transverse leaf spring could be sagging.
And it's Toronado, not Tornado. Sacrilege!

Sep 01, 2011 | Oldsmobile Toronado Cars & Trucks

2 Answers

If rearbag has a hole will this affect start ing? Depletes charge in new battery


You will have to turn the air ride system off until the bag is fixed. Otherwise the pump will run continuously trying to fill the bag. This will obviously kill the battery.

Feb 18, 2011 | 1999 Lincoln Town Car

1 Answer

Tell me how the rear suspension works. the rear


There is a compressor underneath the car on the passenger side (RHD) which inflates two rubber suspension bags on the rear axle. This is controlled by the SLABS ECU and a pair of height sensors on the rear trailing arms.
You probably have two failed bags, and may now also have a knackered compressor if it's not managing to inflate it due to it having been working overtime!
Sometimes you can have issues due to the valve block inside the compressor housing also.
Bags are ~ £100 each, height sensors are ~£35 each, valve block is iirc about £100-£200, and the compressor is £300-400.
Bags/sensors can be DIY'd easily with the right tools.

Jan 20, 2010 | 2001 Land Rover Discovery Series II

1 Answer

EXPEDITION REAR AIR RIDE PROBLEM


do you have just rear air suspension? here's rear only. 4 wheel different. Deler an run a diagnostic test with WDS machine and get fault codes.
-------------------------------------------------------------------------------------
The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving conditions:
  • Ride is improved by using an air type spring (the soft ride is inherent).
  • Handling is improved by maintaining constant vehicle attitude.
The system consists of unique rear air springs, the air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for the RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines and the use of air springs with air spring solenoids.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed or the vehicle speed exceeds 16 km/h (10 mph).
----------------------------------------------------------------------------------------
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket).
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level
------------------------------------------------------------------------------
  • Uneven vehicle height
  • Circuitry.
  • Rear pneumatic fault.
  • Air compressor assembly.
  • Air suspension control module.
  • Go To Pinpoint Test I .

Feb 21, 2009 | 2001 Ford Expedition

2 Answers

Where are the leveling sensors located on a 2003 Navigator?


There is one at each wheel. here is some info

Vehicle Dynamic Suspension The four wheel air suspension system is comprised of the following components:
  • service switch
  • control module
  • two front height sensors
  • one rear height sensor
  • compressor and drier assembly (includes vent solenoid)
  • air lines
  • front and rear air spring and shock absorber assemblies
  • four air spring solenoids
s3j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The service switch for the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the jack storage area in the rear of the passenger compartment. Failure to do so may result in unexpected inflation or deflation of the air springs which may result in shifting of the vehicle during these operations.
s3j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not remove an air spring under any circumstances when there is pressure in the air spring. Do not remove any components supporting an air spring without either exhausting the air or providing support for the air spring to prevent vehicle damage or personal injury.
Air Suspension Pneumatic Diagram 17d59a6.gif
Item Part Number Description 1 5319 Air compressor and drier 2 5B322 Air line T-fitting 3 5B321 Air line union 4 — Air line Y-fitting 5 18945/5311 Air spring and solenoid

Suspension Height Sensor Removal and Installation
NOTE: Front shown, rear similar
  1. s3j~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning off the air suspension switch located in the LH quarter trim panel. Failure to do so may result in unexpected inflation or deflation of the air springs which may result in shifting of the vehicle during these operations.
    Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Disconnect the sensor arm. 721ed10.gif
3. Remove the bolts and the sensor. b198e3c.gif
4.
  1. Disconnect the electrical connector.
---------------------------------------------------------------------------------------------

Ride Height Adjustments
Special Tool(s) s3j~us~en~file=st2332a.gif~gen~ref.gif Worldwide Diagnostic System (WDS)
418-F224

New Generation STAR (NGS) Tester
418-F052 or equivalent scan tool
Inflation and Deflation of the Air Suspension System
  1. NOTE: Make sure that the air suspension switch is in the ON position
    NOTE: Make sure that a battery voltage of at least 11 volts is maintained while carrying out this procedure.
    Turn the ignition switch to the ON position.
  1. Connect scan tool to the data link connector (DLC).
  1. Select Air Suspension Control Module under Active Command Mode:
    • VENT FRNT to deflate the front down.
    • LIFT FRNT to inflate the front up.
    • VENT REAR to deflate the rear down.
    • LIFT REAR to inflate the rear up.
Calibration
Ride Height Resetting
  1. NOTE: Make sure that the air suspension switch is in the ON position
    NOTE: Make sure that a battery voltage of at least 11 volts is maintained while carrying out this procedure.
    Turn the ignition to the ON position.
    • Exit the vehicle, close all doors and allow the system to vent the vehicle down to kneel height (approximately 45 seconds).
  1. With the ignition remaining in the ON position, shift the vehicle into DRIVE and then back to PARK.
    • Exit the vehicle, close all doors and allow the vehicle to pump to trim (approximately 45 seconds).
  1. Measure the ride height. For additional information, refer to Section 204-00 .
  1. Open the LF door.
  1. Connect scan tool to the data link connector (DLC).
  1. While outside of the vehicle, select the proper vehicle year, model and engine type.
  1. Select 4WAS module.
  1. Using the active command mode, vent or lift the vehicle to achieve the correct ride height.
  1. Select the "Save Calibration Values (Store Ride Height)" scan tool command to calibrate the 4WAS module.
-------------------------------------------------------------------------------

Jan 09, 2009 | 2003 Lincoln Navigator

2 Answers

AIR SUSPENTION WORKS ABNORMALY


a lot of info here:
Principles of Operation
The 4-wheel air suspension (4WAS) module commands changes in vehicle height that are necessary for both the load leveling and the vertical height adjustment features.
The 4WAS load leveling feature automatically makes adjustments in vehicle height so that the vehicle is always at trim height, and that constant front-to-rear vehicle attitudes are maintained over the load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle left and right sides for the 4WAS system are restricted to what can be reliably achieved with three height sensors.
The height adjustment feature has three vehicle heights within a two-inch span:
Kneel height — improves the ease of entering and exiting by lowering the vehicle one inch below the trim height in the front and rear when the vehicle ignition is in the OFF or LOCK positions and the vehicle is stationary.
Trim height — normal vehicle ride position; vehicle moves to trim position when the ignition is ON, when the transmission is initially shifted to DRIVE or REVERSE mode, when all doors are closed or when speed of more than 24 km/h (15 mph) is detected.
Off-road height — improves ground clearance by raising the vehicle one inch above trim height in the front and rear when the vehicle is at 4x4 low modes and the vehicle speed is less than 40 km/h (25 mph).
The 4WAS module uses the universal bus protocol, (UBP), module communications network for sending and receiving various signals with the exception of speed, information from the three height sensors, and the air suspension service switch. For additional information about UBP, refer to Section 418-00 .
The 4WAS system holds vehicle height when any door or rear hatch is opened. The system stores front and rear vehicle height the moment any door is detected open. The system then maintains this height regardless of the addition or removal of a load. The system returns to its commanded height when all doors are closed or vehicle speed exceeds 24 km/h (15 mph).


Vehicle Height Modes Ignition State Transfer Case Mode Speed or Speed Range Resulting Vehicle Height OFF 4x2, A4WD, 4x4 HI N/A Kneel (TRIM - 25 mm) ON and RUN 4x2, A4WD, 4x4 HI All speeds TRIM ON and RUN 4x4 Low Below 40 km/h (25 mph) Off-Road (TRIM + 25 mm) ON and RUN 4x4 Low Above 40 km/h (25 mph) TRIM OFF 4x4 Low N/A Stays at current position (prior to ignition transition)
Air Suspension Service Switch
The air suspension service switch signal is needed to wake up the 4WAS module. Without the module receiving this signal, the 4WAS system is inoperative at speeds below 24 km/h (15 mph) and will not react when the vehicle is raised or lowered. At speeds above 24 km/h (15 mph), the system will be active as if the air suspension service switch is in the ON position.
Vehicles without message center When the air suspension service switch is in the OFF position and the ignition switch is in the RUN position, a "CHECK SUSP" will appear in the RH corner of the instrument cluster.
Vehicles with message center When the air suspension service switch is in the OFF position and the ignition switch is in the RUN position, the message center will display "SUSPENSION SWITCHED OFF"
Air Compressor
The air compressor:
  • consists of the compressor and vent solenoid; neither are replaceable as individual items.
  • is a single cylinder electric motor driven unit that provides pressurized air as required.
  • is powered by a solid state relay, which is controlled by the 4WAS module.
  • passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
  • has a single port drier that can be replaced separately.
The vent solenoid:
  • allows air to escape from the system during venting actions.
  • is part of the air compressor cylinder head.
  • shares a common electrical connector with the air compressor motor.
  • is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
  • has an O-ring seal that prevents air leakage past the valve tip.
  • opens when the 4WAS module determines that lowering is required.
  • provides an escape route for pressurized air when system pressures exceed safe operating levels.
  • has a 1034 kPa (150 psi) internal relief valve.
  • is installed with the air compressor as a unit.
Air Spring
The 4WAS system has front and rear air springs. The air springs provide a varying spring rate proportional to the system's air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system's air. Increasing air pressure (compressing) raises the vehicle; decreasing air pressure (venting) lowers the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the 4WAS module command.
Air Lines and Fittings
NOTE: Apply a soapy water solution to the air lines to verify the location of air leaks. If the air lines are cut, ruptured or leaking, a service repair kit is available.
Nylon air lines with quick connect fittings connect to the air compressor and air spring solenoids. The compressor assembly output line is divided by the use of a fitting to supply the front and rear air springs. Fittings are also used to divide the air supply to the RH and LH air spring solenoids.
Air Suspension Height Sensors
There are two sensors used for the front suspension and one sensor used for the rear suspension. The sensors send a voltage signal to the 4WAS module. The output ranges from approximately 4.50 volts at minimum height (when the vehicle is low or in full jounce) to 0.50 volt at maximum height (when the vehicle is high or in full rebound). The sensors have a usable range of ± 45° compared to total suspension travel of 196 mm (7.84 in) at the front wheels and 240 mm (9.6 in) at the rear wheels. Therefore, the sensors are mounted to the suspension at a point where full suspension travel at the wheel is relative to the travel at the height sensor. The front height sensors are mounted to the frame and the links are attached to the upper arm ball studs. The rear height sensor is mounted to the frame and the link is attached to the rear lower arm ball stud.
When the height sensor indicates that the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the system. When the sensor indicates that the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the system to lower the vehicle to its trim height level.
Compressor Relay
A solid state relay is used in the air suspension system for compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the 4WAS module.
The compressor solid state relay is energized by the 4WAS module to have high current flow from the battery to the compressor motor.
4-Wheel Air Suspension (4WAS) Module
NOTE: The 4WAS module must receive a ride height adjustment calibration and must pass a pneumatic test when it is installed new or swapped.
The 4-wheel air suspension (4WAS) module controls the air compressor motor (through a solid state relay), all air spring solenoids, and provides power to front and rear height sensors. The 4WAS module also controls vehicle height adjustments by monitoring the three height sensors and other universal bus protocol (UBP) signals. The 4WAS module conducts all fail-safe and diagnostic strategies, and contains self-test and communication software for testing the vehicle and related components.

Jan 06, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...