Question about 1994 Plymouth Sundance

1 Answer

I have a 1994 plymouth sundance when the fan is turned on the temp, and fuel gauge peg out (read maximum) the volt gauge reads zero. Also both green arrow turn singal indicators on the dash light up. Also I have a scanner. Where do I hook it up?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 5,763 Answers

This car is obd 1 so your would need to have a scanner that connects to OBD1, the caonnection ie under the dash, but is diffrent from the newer cars with OBDII, this problem sounds like a bad feed due to a short maybe in the blower resistor or the heater controls, i would start with the resistor then work my way to controls take a good look at the fan switch, hope this helps.

Posted on Sep 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to relieve gas pressure off fuel filter of 1994 2.2 liter plymouth sundance


disconnect power supply to fuel pump, then start engine when engine stalls fuel pressure released

Jun 02, 2012 | 1994 Plymouth Sundance

1 Answer

My Plymouth sundance 1994 2.5l Auto seat belt will not move. The light stays on the dash board, and when i run my blower to high or to much current, my speed gauge goes to zero and the mileage stops...


Hm. auto seat belt not moving points to a burnt out motor or a fuse is blown.

Have you had the starting and charging systems tested by Sears or Walmart?

How does it start?

Jul 10, 2010 | 1994 Plymouth Sundance

2 Answers

Where is the fuel filter


To the rear of the gas tank under the car.

Oct 20, 2009 | 1994 Plymouth Sundance

1 Answer

My sundannce is putting out a 3 5 5 code what does it mean?


The trouble code that you gave is not a code. If it 35 its the radiator fan relay circuit. The 55 it means end of fault reading mode. Recheck code. Going to local autozone they will check it for free.

Oct 06, 2009 | 1994 Plymouth Sundance

1 Answer

I need all the engine diagnostic codes for a 94 plymouth sundance


11 Timing belt2.gif skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM/ECM was disconnected within the last 50 key-on cycles (normal)
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failur

Jul 08, 2009 | 1994 Plymouth Sundance

1 Answer

Instrument panel dials all pegged to zero or max


ok let me help you get started
this isnt going to be easy we need to do a bunch of testing.
you will need a 12 volt test light.
remove the negitive battery cable and connect one side of your test light to the battery negitive and the other side to the battery cable . and with the key off.. so now if you have a short some where the light should be lit. now what we have to do is start to pull fuses untill the light goes out. and when you find the fuse that is causing your short and drain your battery . then we have to look into the section of the wiring and components.
let me know what you find
later paul

Oct 18, 2008 | 2003 Ford Focus

Not finding what you are looking for?
1994 Plymouth Sundance Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...