Question about 1998 Chevrolet Monte Carlo

1 Answer

How do I remove the steering wheel trim and replace the turn signal switch on a 1998 monte carlo z34?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

If this critter has an airbag in the steering wheel, and I'll bet it does; then you should have this done by a dealer. Pulling the wheel off and replacing the multifunction switch underneath needs to be tended to by a trained person.

Posted on Sep 13, 2010

Testimonial: "Thanks for the info, will do."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE 4T60E TRANSMISSION FROM A 96 Z34 MONTE CARLO?


You don't have to pull it to replace the TCC. Remove the pan and you can access the TCC solenoid. 40b12bb6-08f8-4f1c-b959-9bfe6f7b08fb.gif

Aug 06, 2014 | 1996 Chevrolet Monte Carlo

1 Answer

Where is the flasher relay on a 2002 monte carlo


It's part of the hazard switch. have to take trim panel off to replace it .Apply the parking brake.
If the vehicle is equipped with a column shift, position the transaxle shift control indicator to 1.
Adjust the steering wheel for access.
Using a small, flat-bladed tool, gently remove the bezel from the ignition lock cylinder.
For the Impala, remove the right and the left access covers from the instrument panel (IP) fuse block.
For the Monte Carlo, remove the left access cover from the IP fuse block.
Remove the steering column filler. Refer to Steering Column Opening Filler Replacement .
For the Monte Carlo, open the instrument panel compartment door.
Remove the trim plate screws from the IP cluster.
Start at the left side of the IP cluster trim plate. Grasp the trim plate and carefully pull rearward. Disengage the IP cluster trim plate in order to easily access the hazard warning switch
Disconnect the electrical connectors from the hazard warning switch.
Remove the hazard warning switch from the IP cluster trim plate.


13710300-sqgggmolzf4u4c55ip0gdkvq-5-0.jpg It's probably the switch on the steering column ! An not the flasher but you never know without testing .
Turn Signal Lamps and/or Indicators Inoperative
Step
Action
Yes
No
Schematic Reference: Exterior Lights Schematics
1
Did you perform the Lighting System Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Lighting Systems
2
Turn the ignition to the ON position.
Place the turn signal switch to a turn left or a turn right position.
Do the turn signal tamps flash ON and OFF?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3
3
Disconnect the hazard switch.
Connect a test lamp between the TURN SIGNAL Fuse battery positive voltage circuit and ground.
Does the test lamp illuminate?
Go to Step 4
Go to Step 7
4
Reconnect the hazard switch.
At C201, connect a test lamp between the turn signal flasher supply circuit and ground.
Does the test lamp flash ON and OFF?
Go to Step 5
Go to Step 6
5
At C201, connect a test lamp between the turn signal flasher supply circuit of the hazard switch and inoperative turn signal lamps supply voltage circuit.
Does the test lamp flash ON and OFF?
Go to Step 9
Go to Step 8
6
Test for a high resistance or an open in the turn signal flasher supply circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10
7
Repair a high resistance or an open in the TURN SIGNAL Fuse battery positive voltage circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 11
--
8
Repair a high resistance or an open in the turn signal lamps supply voltage circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 11
--
9
Replace the turn signal switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 11
--
10
Replace the hazard switch. Refer to Hazard Warning Switch Replacement in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 11
--
11
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jul 21, 2012 | 2002 Chevrolet Monte Carlo

1 Answer

I have a 1997 Monte Carlo Z34. We replaced the turn signal switch and had to replace the power steering pressure hose. Now the car will not start it will crank but no fire. Any ideas or suggestions? It was...


sound like you have wires disconected somewhere
check with areas of last repair sensors on engine (crank / cam)
or lower sterring colum area also check the fuses one may have burnt up
if you did not remove battery conection prior to repair

May 21, 2011 | 2003 Chevrolet Monte Carlo

1 Answer

How hard is it to replace hub assembly(bearings) on a 1999 Monte Carlo z34?


Not to bad you need remove wheel first then remove 2 bolts from brake caliber put caliber to the side or better yet hang it on the stut spring with a zip tie then remove 2 bolts that hold the brake caliber bracket on put it to the side then remove rotor then remove the big nut on the center of the axle then get a hub puller or a cold chisel to seperate the hub from the steering knuckle oh disconnect the ABS sensor from connection.

May 12, 2011 | 1999 Chevrolet Monte Carlo

1 Answer

My ignition switch is jammed on my 1985 monte carlo any suggeestions


you will have to replace the lock cylinder in the steering column. This is a diy job, if you can borrow or rent 2 tools. One is a steering wheel puller, and the other is a lock plate depressor. Some part stores will loan/rent these tools. Once you have the tools proceed as follows: 1 remove steering wheel with steering wheel puller
2 install lock plate depressor and depress the lock plate to remove the retaining ring. 3 Remove the turn signal lever and hazard light button, then the three screws that hold the turn signal switch, pull up on the switch and push it out of the way. You may have to get under the dash and unplug the harness to the switch to get enough slack to clear the steering column. 4 remove the lock cylinder retaining bolt then slide the lock out. slide the new lock in replace the retaining bolt and reassemble the column.

Aug 24, 2010 | 1985 Chevrolet Monte Carlo

2 Answers

1998 Chevrolet Monte Carlo brake lights do not


check blubs if the center light works should be working side brake lights

Sep 07, 2009 | 1998 Chevrolet Monte Carlo

2 Answers

My turn signal flashes really fast I replaced the bulb and it still does it unless you wiggle the handle, The handle its self works properly i.e. clicks into position for left or right turn, is there a...


try your emergency flashers, do they blink at a normal speed? if yes, replace flasher for turn signals.if not check the bulbs on the side that blinks fastest,even if they look good there could be a broken filiment.tap on the bulb, if the filiment moves it's a bad bulb.

Jul 09, 2009 | 1998 Chevrolet Monte Carlo

5 Answers

1998 monte carlo brake light problems


Turn signal switch. With you foot on the brake have someone stand behind the car. Wiggle the turn signal lever and see if the the brake lights flicker.

Jun 24, 2009 | 1998 Chevrolet Monte Carlo

1 Answer

1995 Chevy Monte Carlo


you need to take the upper and lower steering column covers off, should be 3 screws in bottom, take tilt steering lever out if neccessary, it is a 2 peice cover, take apart, change switch and put back together

Nov 03, 2008 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
1998 Chevrolet Monte Carlo Logo

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...