Question about 1983 Peugeot 504

2 Answers

Stabler at high speeds

How do you make your car more stable at high speeds?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 40 Answers

...the easy ways are...change the shock absorbers to hard with gas filled not oiled filled...change the tires to 185 x 60 x 15" change and lowering the spring...if you can then add front, sides spoilers and wing spoiler...

Posted on Jul 11, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 291 Answers

Lower the car, add a spoiler, low profile 18" tyres and a phat body kit. Add rear stabalisers .

Posted on May 15, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

After service my Mazda etude16 valve engine,the car misfires and drives stable in high speed and in low gears it has no power.

If the check engine is on I belive most likely to be a bad sensor, you can take it to any auto zone and they will read the codes for free, it might be the oxigen sensor or the crankshaft sensor that's giving you problems.

Theyre not expensive and go bad much too often.

Pls rate, thank you

Oct 03, 2016 | Mazda Cars & Trucks

1 Answer

After service my Mazda etude16 valve engine,the car misfires and drives stable in high speed but I'm low gears it has no power.

You don't say what year it is, but some have an ignition module with two or more sections for different rpm ranges. The later models may have variable cam timing and if this fails in high rpm mode it will cause this too.

Oct 03, 2016 | Mazda Cars & Trucks

1 Answer

Can i put 195 60 16 tires on my lincoln town car when recomended tire is a 225 60 15

You can bot you shouldn't. I understand it's not good to have car well balanced and stable braking.
If you decide, don't run at high speed.

Jul 22, 2015 | Lincoln Cars & Trucks

2 Answers

Battery light staying on after new battrey and alternater

Suggest you to vehicle charging circuit for a thorough examination.
The first is to measure the battery tester, suggest you use high frequency discharge gauge or battery measurement, the load current is less than 110 of the cases, the minimum voltage shall not be less than 9.6 volts, and remained stable in 5 seconds. If the voltage below 9.6 volts, but can keep stable inside said in 5, excessive discharge, should be timely supplementary charge; if the voltage below 9.6 volts, to maintain stable and rapid decline to 0 volts or close to 0 volts in 5 seconds can not, indicates that the battery failure.
Then check the generator power output, recommend looking for car condition with a multimeter in parallel with the positive and negative poles battery, the output voltage and stepped on the gas check generator in high speed condition is in the 14V positive and negative 0.25V or so, if the lower or higher than the standards, then the generator failure. Use obd2 tools for automotive diagnostics , you can improve vehicle safety performance and driving more safer.

Nov 27, 2013 | 2005 Ford Escape

1 Answer

I am trying to set the idle on 2012 corolla s to about 1000 rpm for electrical functions on a high out put alternator to work properly. any insight would be appreciated.

All the Parameter Identifications are preset and you cannot alter them. Though you can achieve stable rpm with or without load by the process which is known as engine tune up, throttle body cleaning and relearning the idle speed control valve.

Sep 16, 2013 | Toyota Corolla Cars & Trucks

1 Answer

Not stable in high speed

it is an SUV, meaning it is top heavy compared with lower slung vehicles, if you are driving at high speed you are asking for a tip and roll and roll. please do this type of driving all by yourself, and limit the number of fatalities. google and read the sorry stories about the early Ford explorer II. I would however, also get a good 4 wheel alignment done and replace the all worn suspension components on this 11 year old vehicle.

Nov 18, 2010 | 1999 Suzuki Grand Vitara

1 Answer

The automatic won't shift up to high or OD and speedometer quit working at the same time?

sounds like your vehicle speed sensor is broken. here is a tutorial from


The vehicle speed sensor is made up of a coil mounted on the transmission and a tooth rotor mounted to the output shaft of the transmission. As each tooth nears the coil, the coil produces an AC voltage pulse. As the vehicle speed increases the number of voltage pulses per second increases.


See Figure 1

  1. To test the VSS, backprobe the VSS terminals with a high impedance voltmeter (set at the AC voltage scale).
  2. Safely raise and support the entire vehicle using jackstands. Make absolutely sure the vehicle is stable.
  3. Start the vehicle and place it in gear.
  4. Verify that the VSS voltage increases as the drive shaft speed increases.
  5. If the VSS voltage is not as specified the VSS may be faulty.

0900c1528008f10b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Vehicle Speed Sensor (VSS) and vehicle speed signal buffer wiring diagram


See Figure 2

  1. Disconnect the negative battery cable.
  2. Disengage the electrical connection.
  3. Unfasten the sensor retainers.
  4. Remove the sensor and gasket or O-ring.

To install:
  1. Install the sensor with a new gasket or O-ring.
  2. Fasten the sensor retainers.
  3. Engage the electrical connections.
  4. Connect the negative battery cable.

0900c1528008f10c.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Vehicle Speed Sensor (VSS) location

Oct 13, 2010 | 1994 Chevrolet C1500

1 Answer

Idle is not stable

check for a vaccum leak or test throttle position sensor

Oct 16, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Wahs Team

Level 2 Expert

205 Answers


Level 3 Expert

71338 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides