Question about 2003 Lincoln LS

1 Answer

Wrench light comes on car goes into limp mod turn car off ,turn back on car is fine

Posted by on

1 Answer

It is not fine
You can not use it that way
You have a really bad ignition coil, spiking the PCM,putting it into ETC Failsafe

Posted on Oct 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 mercedes c230 kompressor


air leak in compressor output hoses/intercooler problem

May 13, 2017 | Cars & Trucks

1 Answer

Help. check engine light comes on also yellow open end wrench light comes on.


Have you had the engine computer checked for trouble codes ?

Sep 05, 2015 | 2005 Lincoln LS V6

2 Answers

Why does my traction control and eml light come on Bmw e46 ?


I'm sorry Roger but you are going to have to get it to someone with access to the plug in diagnostic unit for Beemers.
there seem to be several things going on but when it coughs up the diagnostic info you may go straight to it?

Jun 05, 2014 | Cars & Trucks

1 Answer

2006 Ford Freestyle wrench light comes on and goes into limp home mode how do you fix


There is no way to get around a proper repair on a computer controlled transmission, that is wishful thinking. What is the fault code that is memory? Have you even run the system scan yet?

Apr 23, 2012 | 2006 Ford Freestyle

1 Answer

We have a 2006 Ford f250 super duty powerstroke F4X4 and the wrench symbol came on while driving, when turned off it went off, started driving toward home and it came back on again. What does this me


Sounds like 2 separate problems. The wrench light signifies that the truck goes into" limp home" mode and that there is a problem with your electronic speed control. As far as the truck pulling; is it doing it just driving without using the brakes? It could mean that you may need an alignment, tire rotation , low tire pressures or all of the above. Good luck to you

May 11, 2017 | 2006 Ford F-250 Super Duty

1 Answer

2005 Lincoln LS in Limp Mode. I can start the car and it runs fine for about 10 seconds then goes into "limp mode" How can I reset this?


You have a very bad COP Ignition Coil,that is spiking the PCM (computer)
The spike comes back on the TPS Sensor,then the PCM doesn't see the
throttle signal your foot sent thru, the pedal actuator (gas pedal) ,so it puts the
car into ETC Failsafe,and you can only go 6 mph.

If you got no ETC Failsafe, on the bottom right side of the dash, tell me what you do have
I need all the codes,if you have a MIL Lamp on ( the one that looks like a wrench)

Dec 01, 2010 | 2005 Lincoln LS

1 Answer

My transmission light comes on


Most likely fault is a ground. But could be anything electrical.

Jul 21, 2009 | 1991 Jaguar XJ6

1 Answer

Limp home mode


You need to scan for engine trouble codes. Most parts stores will do this for free, and tell you what they mean and make recommendations on what to do. The 'limp mode' kicks in to prevent damage to the vehicle when the computer gets data that something is wrong.. When you shut it off, it's temporarily reset, but then the cars computer is signaling there is still a problem, and it goes back into limp mode. If you have any questions after getting the codes 'read' , post questions and code #;s here for help. Good luck.

Apr 28, 2009 | 2004 Ford F150

1 Answer

1996 dodge avenger when cold, the transmission go in limp mode


Is the vehicle's Check Engine Light on? It should briefly light up when you turn the key on (before you start the engine) to show that the light is working correctly. Based on what I've read I believe you should have one or more trouble codes. A place like AutoZone will read the trouble codes for you for free, and you can look them up here - http://www.engine-light-help.com/generic-check-engine-light-codes.html

Dec 12, 2008 | 1998 Dodge Avenger

2 Answers

1997 isuzu wizard mu check light


Code 24 is a vehicle speed signal sensor fault, the sensor most likely does not provide a useable signal until about 25 MPH, when the computer doesn't see any signal after that speed it turns on the light. Make sense?

Sep 08, 2008 | 1997 Isuzu Oasis

Not finding what you are looking for?
2003 Lincoln LS Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...