Question about 2002 Chrysler Town & Country

1 Answer

How do you remove top bolt on the starter - 2002 Chrysler Town & Country

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 2,019 Answers

I don't remember for sure, but I believe a long extension is what is needed.

Posted on Sep 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Remove a starter


  • Remove the negative and positive lead on the battery.
  • Locate the starter under the vehicle. The starter will be located to the right of the motor on the bottom. Access the bolts comfortably from underneath the truck.
  • Remove the bottom bolt with a socket wrench. The ground cable will be attached. Save the bolt for reinstalling the starter.
  • Unbolt the positive cable on top of the starter. Use a socket wrench to remove the bolt.
  • Unbolt the top of the starter with a socket wrench. The starter will be loose.
  • Pull the starter straight out. Use both hands to pull out and forward as the starter is heavy. Pull forward and lower to the ground.
Installing the Starter
  • Position the new starter in place. Match up the starter to the designated bolt holes on the mounts.
  • Start the top bolt. Turn the bolt clockwise but do not tighten the starter down.
  • Start the bottom bolt. Ensure the negative cable is run through the bolt before starting. Do not tighten the bolt.
  • Tighten the top bolt with the socket wrench. Tighten it snug. Repeat the same for the bottom bolt. Ensure both bolts are tight.
  • Tighten the positive cable to the starter. Ensure the cable is snug to the fitting.
  • Connect the terminals to the battery. Ensure the vehicle cranks. The starter will engage without hesitation if done correctly.


Read more : http://www.ehow.com/how_5707471_replace-starter-ford-ranger.html

Dec 05, 2015 | 2006 Ford Ranger 4.0

1 Answer

Remove and replace starter


Replacing starter is not a difficult job.The vehicle needs to be lifted up on jack stands.The starter needs to be accessed from under the car. --------- You need to remove the air filter housing and intake, and the battery and tray if you want to make it easy on yourself. Remove those first, then remove the top starter bolt before you go under the car.

Accessing the top starter bolt,sometimes takes time. The top bolt comes from the transmission side on top.
-----------
Click this link below to see diagram showing location of top bolt:--- http://technoanswers.blogspot.com/2011/10/how-to-replace-starter-on-2000-mazda.html --------- This will help.Thanks.Helpmech.

Oct 07, 2011 | 2000 Mazda Protege

1 Answer

I am replaceing the starter on a 1998 toyota corolla 1.8 ltr. How do I get to the top bolt on the starter to remove it ?


Hello,

To replace the starter of a 1998 toyota corolla, please follow the steps below:
  1. Remove the key from the ignition, and remove the battery, do not attempt this with the battery in car.
  2. Remove the battery and tray.
  3. Look to the rear of the engine, You'll see the top of the starter, loosen and remove the 14mm bolt/nut holding it down below,
  4. Drain the radiator and remove the lower radiator hose. This will let You squeeze the starter around the AC line,
  5. Then install the new starter, the one bolt You removed from the bottom, screw the last 14mm bolt on the starter into the transmission loosely,
  6. Go up top, reinstall the top bolt, tighten this firmly but not all the way,
  7. Go below, tighten the bottom bolt to final spec.
  8. Reattach all the wires, make sure the trigger wire is snapped in fully.
  9. Go up top, firmly firmly tighten to spec the top bolt,
  10. Reinstall everything You removed up top the below,
  11. Reinstall the battery and make sure the ignition is off while doing this,
  12. Hook up battery and ensure every thing that was loosened has been installed back on.
  13. Then You crank it to see if it will start.
Hope this helped. Thank You for using FixYa!!!

Jan 26, 2011 | 1998 Toyota Corolla

1 Answer

How to remove a starter from a 2003 expidition


Thank you for using Fixya.
Heres's the procedure on how to remove and install starter for your 03 Expedition. First remove the battery cables from the battery. Remove the electrical connections to the starter and label for replacement. There are 3 bolts - 13mm. The bottom bolt is also the ground terminal, therefore you will need a deep socket for that bolt. The other two are accessable ideally with about a 7" extension to your socket wrench. The top bolt is on the top of the starter and you could fit your hand up there to feel it and place the socket. The 3rd bolt is between the bottom and top bolts. Remove the 3 bolts and the starter falls right out.

All the best!

Nov 16, 2010 | 2003 Ford Expedition

1 Answer

Change starter, how to get to, from under of from top what to take out first to get to the starter


TO REMOVE STARTER YOU HAVE TO REMOVE INTAKE MANIFOLD BRACKET UPPER BOLTS.REMOVE CLUTCH RELEASE CYLINDER AND MOVE IT ASIDE.REMOVE INTAKE MANIFOLD BRACKET LOWER BOLTS AND REMOVE BRACKET.REMOVE STARTER FROM TRANSMISSION.REMOVE STARTER ELECTRICAL WIRES.INSTALL NEW STARTER BACK VISA VERSA. TORQUE STARTER BOLTS 40 FT LBS TORQUE INTAKE BRACKET BOLTS 40 FT LBS.

Oct 08, 2010 | 1999 Kia Sportage

1 Answer

How do i connect my starter to the battery


REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown 87952039.gif
Fig. 2: Remove the starter electrical connections from the back of the starter 91142p05.jpg
Fig. 3: Remove the three bell-housing cover retaining bolts and . . . 91142p06.jpg
Fig. 4: . . . remove the bell-housing cover 91142p07.jpg
Fig. 5: Remove the starter support brace-to-engine bolt 91142p08.jpg
Fig. 6: The starter is retained by two bolts 91142p09.jpg
Fig. 7: Remove the bolts and . . . 91142p10.jpg
Fig. 8: . . . remove the starter from the engine 91142p11.jpg
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside 91142p12.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
  8. Transfer the starter support bracket to the new starter if the starter is being replaced.
  9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  11. Install the bell-housing cover.
  12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  13. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines 87952040.gif
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle. To install:
  9. Raise the starter to the vehicle, then attach the wiring.
  10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  11. If moved, reposition the engine wiring harness.
  12. Carefully lower the vehicle.
  13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  14. Fasten the air inlet duct to the throttle body.
  15. Connect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1996 Chevrolet Cavalier

1 Answer

How to replace a starter in a 1996 acura tl 2.5?


  • Since the starter involved the electrical system, disconnect the negative battery terminal to avoid any electrical shorts or other issues.The starter is located on the driver's side just below the intake manifold and near the firewall. Remove the transmission dip stick, which partially obstructs the starter.Loosen the top bolt on the starter with a 14-mm wrench and loosen the bottom bolt with a 17-mm wrench a couple of turns but do not remove the bolts.After both of the bolts are loose, remove the top bolt and then the bottom bolt and pull the starter out of the transmission bell housing. You will have to angle the starter a little to remove it.Remove the wire that goes to the ignition switch. The wire should simply slide off. Use the 9-mm wrench to disconnect the nut that holds on the solenoid wire.
  • Place wires on the new or remanufactured starter and place it back in the bell housing
  • Replace the top and bottom bolts.Put transmission dipstick back in the gearbox and reconnect the battery.



  • Jul 20, 2010 | 1996 Acura TL Series

    1 Answer

    How to take out the starter?


    REMOVE KEY FROM IGNITION!!!!!! (SAFETY FIRST!!!!) UNHOOK..AND REMOVE THE BATTERY! DO NOT attempt this with the battery IN car..way too many things to go wrong.
    Remove the battery and tray.

    LOOK to the REAR of the engine,you'll see the TOP of the starter.. Loosen and remove the 14MM bolt/nut holding it on now down below

    Drain radiator and Remove the lower radiator hose. This will let you squeeze the starter around the AC line.

    THEN install the new starter,the one bolt you removed from the bottom,screw in the LAST 14MM bolt on the starter into the transmission LOOSELY!!!!!!!

    GO up top,reinstall the TOP bolt,TIGHTEN THIS ONE FIRMLY,but NOT all the way... Go below,tighten the bottom bolt to final spec. RE-ATTACH ALL THE WIRES...make sure the trigger wire is snapped in fully. GO up top,FIRMLY tighten to spec the top bolt.. Re-install everything you removed up top then down below Reinstall the battery(MAKE SURE THE IGNITION IS OFF!!!!!) Hook up battery...

    LOOK AT EVERYTHING...see if ANYTHING is loose.. CHECK EVERY BOLT YOU TOUCHED TO SEE THAT IT IS TIGHT, MAKE SURE ALL WIRES ARE IN PLACE... Crank it...Does it crank?? it should fire MUCH better then when you started....good luck..

    Apr 28, 2010 | 1998 Toyota Corolla

    1 Answer

    93 saturn twin cam starter removal


    Top bolt is almost dirrectly above bottom bolt but,toward engine about 1 inch. slip 13mm.socket with enstention behind starter solenoid ,you have to fish for this bolt.Very hard if you do not have a rack,We always remove it from bottom.

    Jun 14, 2009 | 1994 Saturn Sl

    Not finding what you are looking for?
    2002 Chrysler Town & Country Logo

    Related Topics:

    68 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    74896 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7688 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...