Question about 1995 Chevrolet K1500

Open Question

HOW TO REPLACE HEATER CORE ON 1995 CHEVY 10 VAN

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Heater core

HEATER CORE REPLACEMENT

Posted on Jun 21, 2008

Ad
Shouldibuyit
  • 44 Answers

SOURCE: replace heater core 1994 chevy g20 conversion van

Here a are the instuctions to remove it. I did not know if you have A/C or not so I included both for you.

REMOVAL & INSTALLATION
Without Air Conditioning
ALL MODELS
See Figure 1

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery bottle.
  3. Place a pan under the van and disconnect the heater intake and outlet hoses. Quickly remove and plug the hoses and support them in an upright position. Drain the coolant from the heater core into the pan.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw. Remove the duct.
  2. Remove the engine cover.
  3. Remove all the instrument panel attaching screws.
  4. Carefully lower the steering column. Raise and support the right side of the instrument panel. Refer to for further details.
  5. Remove the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  6. Disconnect the temperature door cable. Carefully fold the cable back and out of the way.
  7. Remove the three nuts from the engine compartment side of the distributor case and the screw from the passenger compartment side.
  8. Remove the heater case and core assembly.
  9. Remove the core retaining straps and remove the core.
To install:
  1. Install the core.
  2. Install the core retaining straps.
  3. Install the heater case and core assembly.
  4. Fasten the three nuts on the engine compartment side of the distributor case and the screw on the passenger compartment side.
  5. Connect the temperature door cable.
  6. Install the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  7. Install the steering column.
  8. Fasten all the instrument panel attaching screws.
  9. Install the engine cover.
  10. Install the duct. Install the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw.
  11. Connect the heater intake and outlet hoses.
  12. Fill the cooling system.
  13. Install the coolant recovery bottle.
  14. Connect the negative battery cable.
1990-95 MODELS With A/C

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.
To install:
  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

Posted on Nov 28, 2008

LEFTY64
  • 69 Answers

SOURCE: Need to replace the heater core in a 1995 Dodge Grand Caravan SE

1991-95 Models

  1. Disable the air bag system by disconnecting the negative battery cable.
  2. Have the system discharged by a qualified professional mechanic using an approved recovery/recycling machine.
  3. Drain the cooling system.
  4. Remove the steering column cover and left and right side under panel silencers.
  5. Remove the center bezel by unclipping it from the instrument panel.
  6. Remove the accessory switch carrier and the heater/air conditioning control head.
  7. Remove storage bin and lower right instrument panel.
  8. Disconnect the blower motor lead under the right side of the instrument panel.
  9. Remove the right side 40-way connector wiring bracket.
  10. Remove the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  11. Disconnect the vacuum lines at the brake booster and water valve.
  12. Clamp off the heater hoses near the heater core and remove the hoses from the core tubes. Plug the hose ends and the core tubes to prevent spillage of coolant.
  13. If equipped with air conditioning, remove the H-valve and condensation tube.
  14. Disconnect the temperature control cable and vacuum harness at the connection at the top of the unit.
  15. Remove the retaining nuts from the package mounting studs at the firewall. Disconnect the hanger strap from the package and rotate it aside.

To install:
  1. Remove the temperature control door from the unit and clean the unit out with solvent. Lubricate the lower pivot rod and its well and install. Wrap the heater core and/or evaporator with foam tape and place in position. Secure with the screws.
  2. Assemble the unit, making sure all vacuum tubes are properly routed.
  3. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  4. Connect the hanger strap from the package and rotate it aside. Install the 2 brackets supporting the lower edge of the heater housing. Connect the blower motor wiring, resistor wiring and the temperature control cable.
  5. Install the retaining screws from the right side to the steering column. Install the instrument panel trim covering and reinforcement.
  6. Assemble the unit, making sure all vacuum tubes are properly routed.
  7. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
  8. Connect the hanger strap from the package and rotate it aside. Connect the blower motor wiring and temperature control cable.
  9. Install the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
  10. Install the right side 40-way connector wiring bracket.
  11. Install the lower right instrument panel and storage bin.
  12. Install the heater/air conditioning control head and accessory switch carrier.
  13. Install the center bezel to the instrument panel.
  14. Install the under panel silencers and steering column cover.
  15. Install the vacuum lines at the brake booster and water valve.
  16. Connect the heater hoses to the core tubes.
  17. Using new gaskets, install the H-valve and connect the refrigerant lines. Install the condensation tube.
  18. Have the system evacuated and recharged by a qualified professional mechanic, utilizing the proper equipment. Add 2 fl. oz. (59 ml) of refrigerant oil during the recharge. Fill the cooling system.
  19. Perform the Air Bag System Check procedures outlined in this section before connecting the negative battery cable.
  20. Connect the negative battery cable and check the entire climate control system for proper operation and leaks.

Posted on Apr 08, 2009

  • 289 Answers

SOURCE: How to replace a heater core in a 1994 chevy 1500

As with all vehicles it seems the first part that they build around is the heater core. It is under the dash above the floor housed in a black plastic sealed box. Sealed with goop. Locate that box and start removing everything around it that is peventing taking the cover off. Of course disconnect the heater hoses under the hood a thefirewall.

Warning it is never as easy as it sounds.

Posted on Nov 29, 2009

  • 8 Answers

SOURCE: replacment of heater core on 01 chevy S-10

Have replaced my heater core in my 2001 regular cab 4wd in december 2009. Had to pull the complete dash including the complete metal dash behind the dash that you see. Also had to remove the right passenger side inner fender well to acess the remaining two bolts that hold the heater core cover to the firewall. Its an insane job to do but the repair shop books call for 9 1/2 hrs to do the job. I'm not an expert but this is what it takes.

Posted on Mar 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the heater core in my 2002 chevy venture van


Look for smaller coolant lines coming off the back of the block or going into the firewall pretty sure it's in the dash

Mar 04, 2015 | Cars & Trucks

1 Answer

How do you fix the heater core in a 1995 chevy van. It is a V6 engine and does have AC


Under the passenger side dash is a plastic cover remove philip screws removethere are thre bolts holding the core to the van unbolt remove the two hose clamps ataching both hoses to core remove hoses and assemble in reverse

Dec 11, 2010 | Chevrolet G10 Cars & Trucks

2 Answers

How do i replace heater core


I believe on a 1987 chevy van the heater core should be under the black plastic cover on the firewall on the left hand side as you are standing in front of the van.
I believe you can also get to it under the passenger side dash.
It is NOT fun. Unless you are a seasoned mechanic, I would not attempt it.
Otherwise stop by your local auto center, and get a HAYNES manual, they will be able to show how to.

Mar 02, 2010 | 1987 Chevrolet G20

1 Answer

1994 Chevy S10 Pick-up 4 cylinder, sloshing noise, no heat......is this a heater core problem?


no heat on this old of a vehicle definitly can indicate a heater core problem. sometimes flushing core with a hose can save heater core sometimes it will need replaced. make sure all coolant is properly disposed of if u flush core yourself

Nov 07, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

Replacing heater core 1995 Lincoln Mark V111


there is a special tool designed for aerostar vans that will sometimes work on your car, check with a kragen or equivelant store to se if you can rent or borrow these tools. hope this helps.

Jun 10, 2009 | 1995 Lincoln Mark VIII

1 Answer

1988 Chevy Blazer Heater Core Replacement


I replaced mine and only took out the glove box.

Jan 14, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

Heater hose, 95 Astro


SOUNDS AS THOUGH THE HEATER CORE IS PLUGGED. TRY BACK FLUSHING IT AGAIN. IF YOU STILL GET NO FLOW IT IS MORE THAN LIKELY PLUGGED AND WILL NEED TO BE REPLACED. THE TUBES ARE VERY SMALL AND PLUG EASILY WITH RUST.

Nov 29, 2008 | 1995 Chevrolet Astro

2 Answers

1998 chevrolet k-1500 heater-core replacement


Remove the heater hose clamps and the hoses from the engine side of the firewall. From the inside under the dash on the pass. side, remove the lower panel screws and slowly pry the lower cover down and the heater core will slide out of the heater box. Installation is reverse of removal.

Sep 20, 2008 | 1995 Chevrolet S-10 CA Edition

1 Answer

Heater core


HEATER CORE REPLACEMENT

Jun 21, 2008 | 1986 Chevrolet G30

Not finding what you are looking for?
1995 Chevrolet K1500 Logo

Related Topics:

546 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...