Question about 2007 Mercedes-Benz Mercedes Benz Clk Class

1 Answer

S/w switch What is s w switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 291 Answers

It has to do with the transmission mission. The 'S' stands for standard, and the 'W' stands for winter. When you are in 'S' mode, the transmission starts out in 1st gear normally, but when you select 'W' mode, the transmission will start out in 2nd gear, to help reduce wheel slip on slippery surfaces.

Posted on May 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear vent controls not working


The rear blower motor switch and the rear floor console switch bezel are serviced only as an assembly.

  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear floor console.
Rear Blower Motor Switch

  1. Remove the rear floor console switch bezel by releasing the retaining tab located at each end of the switch bezel and pushing it out through the front surface of the console.
  2. Disconnect the wire harness connectors from the rear blower motor switch and the rear heated seat switches.
  3. Remove the rear heated seat switches from the rear floor console switch bezel by gently prying the switches free from the back of the switch bezel.
INSTALLATION
  1. Install the rear heated seat switches into the back of the rear floor console switch bezel. Make sure that the switch retaining tabs are fully engaged to the bezel.
  2. Connect the wire harness connectors to the rear blower motor switch and the rear heated seat switches.
  3. Install the rear floor console switch bezel into the rear floor console by pushing it in through the front surface of the console. Make sure that the bezel retaining tabs are fully engaged to the console.
  4. Install the rear floor console.
  5. Reconnect the negative battery cable.

Feb 20, 2014 | Chrysler Pacifica Cars & Trucks

1 Answer

Kexus ignition switch replace


To troubleshoot these issue, for ignition switch replacing procedure:---
Click the link below:---


IGNITION SWITCH REPLACING

It depends on vehicle to vehicle. But it's not very difficult on mot of cars to replace ignition switch. Basic theory of replacing ignition switch is same for all car models. -----

To replace ignition switch on your vehicle, I suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.

-------------

Click the link below: ------

----------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------


Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-----------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

---------

These will help.

Thanks.

Dec 06, 2012 | 1993 Lexus Es 300

3 Answers

How to replace ignition switch


It depends on vehicle to vehicle.But its not very diffult on mot of cars to replace ignition switch.Basic theory of replacing ignition switch is same for all car models.:-----
To replace ignition switch on your vehicle,i suggest you few helplinks with proper ignition switch replacing procedure. View its details and you can replace ignition switch on your vehicle.-------------Click the link below :----------------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to replace Ignition Lock Cylinder on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-lock-cylinder.html

--------------


Ford Taurus: Ignition Switch & Steering Column Replacing?

http://repairhelpcenter.blogspot.in/2012/06/ford-taurus-ignition-switch-steering.html

-----------

How to replace Ignition Switch on Acura Car Models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-ignition-switch-on-acura.html

--------------


How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

------------
1995 Ford Taurus: Ignition switch not turning OFF? http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html
-----------
Ignition Switch Will Not Turn Off? http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
---------
These will help.
Thanks.


Nov 25, 2012 | Cars & Trucks

1 Answer

Giving code p0704


P0704- Clutch Switch Input Circuit Malfunction

Possible Causes:
- Open or short clutch switch circuit
- Poor clutch switch circuit connection
- Damage clutch switch
- Misadjusted clutch switch
- Damaged ECM

Possible Solution: Check clutch switch adjustment, the switch should open and close when the clutch pedal is depress. If the switch is properly adjusted, replaced the clutch switch to resolve problem.

Aug 26, 2011 | 1998 Dodge Avenger

1 Answer

THE "SWITCH" GOES BAD EVERY


Please look at the list below, keeping in mind that this is not an exhaustive list of the switches that your vehicle is equipped with. After staring at the list for a while, tell me what is wrong with your question.

>> A/C High Pressure Switch
>> A/C Low Pressure Switch
>> A/C Refrigerant Pressure Sensor / Switch
>> Ambient Temperature Sensor / Switch HVAC
>> Blower Motor Switch
>> Brake Fluid Level Sensor/Switch
>> Brake Fluid Pressure Sensor/Switch
>> Brake Light Switch
>> Brake Switch (Cruise Control)
>> Cabin Temperature Sensor / Switch
>> Combination Switch
>> Coolant Temperature Sensor/Switch (For Computer)
>> Cruise Control Switch
>> Door Jam Switch
>> Door Sensor/Switch (For Alarm)
>> Door Switch
>> Driver Information Center (DIC) Switch
>> Engine - Coolant Temperature Sensor/Switch
>> Fluid Pressure Sensor/Switch
>> Fog/Driving Lamp Switch
>> Fuel Door Switch
>> Garage Door Opener Switch
>> Glove Box Lamp Switch
>> Hazard Warning Switch
>> Headlamp Dimmer Switch
>> Headlamp Switch
>> Heated Glass Element Switch
>> High Pressure Sensor / Switch
>> Hood Switch / Sensor
>> Horn Switch
>> Ignition Switch
>> Ignition Switch, Buzzer
>> Low Pressure Sensor / Switch
>> Neutral Safety Switch
>> Parking Brake Release Switch
>> Parking Brake Warning Switch
>> Power Door Lock Switch
>> Power Mirror Switch
>> Power Seat Switch
>> Power Window Switch
>> Pressure Cycling Switch
>> Rear Defogger Switch
>> Refrigerant Pressure Sensor / Switch
>> Remote Switch
>> Seat Belt Buckle Switch
>> Seat Heater Switch
>> Seat Memory Switch
>> Shift Interlock Switch
>> Sunroof / Moonroof Switch
>> Telescoping Wheel Switch
>> Tilt Wheel Switch
>> Traction Control Switch
>> Transmission Mode Switch
>> Transmission Temperature Sensor/Switch, A/T
>> Trunk / Liftgate Switch
>> Trunk/Liftgate Sensor/Switch (For Alarm)
>> Turn Signal Switch
>> Underhood Lamp Switch
>> Valet Switch
>> Washer Fluid Level Switch
>> Windshield Washer Switch

Aug 17, 2011 | 2001 Cadillac DeVille

2 Answers

All doors are closed and it said a door is still open


It is probably due to a faulty "jab switch" (the button that the door pushes against when the door closes). Purchase one good jab switch and replace one switch at a time to determine which switch needs replacement. During your diagnosing, when everything works properly, leave that switch in place, it has been repaired. Hopefullly, this will help to FixYa problem!

Oct 13, 2010 | 1996 Ford Explorer

1 Answer

Replaced the bulbs and checked fuse but the brakelights fail to work. Could it be a switch.


Yes, it could be the switch behind your brake pedal.

  1. Remove the driver's side instrument panel trim panel/sound insulator.
  2. Detach the switch electrical connector.
  3. Remove the switch from the retainer by grasping it, turning the switch 90° counterclockwise, and pulling it toward the rear of the car.

082d67c.gif
The brake light switch (3) is mounted on the brake pedal support (1) and secured with a retainer (2)

To install:
  1. Insert the brake light switch into the retainer until the switch body seats on the retainer.
  2. Pull the brake pedal upward against the internal pedal stop.
  3. Turn the switch 90° clockwise in order to lock it into position.

NOTE Proper switch adjustment is achieved when no clicks are heard as the pedal is pulled upward and when the brake lights do not stay on without brake application.


  1. Attach the switch electrical connector and test the switch for proper adjustment.
  2. Adjust the brake light switch, as follows:
    1. Detach the switch electrical connector.
    2. Remove the switch from the retainer by turning it counterclockwise 45°, and pulling it toward the rear of the car.
    3. Insert the switch into the retainer until the switch bottoms out against the brake pedal and the switch actuator button is fully depressed.
    4. Snap the switch into the retainer by turning it clockwise 45° until a click is heard.
  3. Attach the switch electrical connector.
  4. Install the hush panel/sound insulator.
  5. Connect the negative battery cable.

Sep 13, 2010 | 1998 Oldsmobile Cutlass

1 Answer

Ignition switch replacment


The ignition switch is usually mounted to the steering column and is operated by a linkage rod.

NOTE On column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.

bbd532a.gif

The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch:
  • Remove the ignition switch wiring harness.
  • Unbolt it from its position.
  • Bolt the new switch into position.
  • Attach the witing harness.

Its possible that this video can helped (for Explorer)...


Good luck.

Mar 18, 2010 | 1999 Ford Expedition

1 Answer

1998 Mercury Villager Break light switch


go here for help. http://autos.groups.yahoo.com/group/villagerquest/

Brake light circuit goes through turn signal switch. Do turn signals work ok? Does high mount stop lamp do this too? If you disconnect brake switch, do the lights go off? Do you have trailer tow? Maybe that wire is an issue. I would check brake switch first again. Maybe out of position.

I think you need to adjust the switch.

Installation
  1. Install the BPP switch.
  1. Adjust the BPP switch. Refer to the procedure in this section.
  1. Tighten the BPP switch locknut to 12-15 Nm (9-11 lb-ft).
  1. Connect the BPP switch electrical connector.
  1. Connect the battery ground cable.
Section 17-01: Lighting, Exterior 1998 Villager Workshop Manual
ADJUSTMENTS Brake Pedal Position (BPP) Switch
  1. Measure the distance between the brake pedal stopper and the threaded end of the brake pedal position (BPP) switch. The BPP switch height (A) should be 0.3-1.0mm (0.012-0.039 inch).


ce51ecc.gif

  1. If the BPP switch height is not within specification, loosen the BPP switch locknut.
  1. Adjust the BPP switch until the height is within specifications.
  1. Tighten the BPP switch locknut to 12-15 Nm (9-11 lb-ft).
STOPLAMPS Condition Possible Source Action
  • Stoplamps/Rear Hi-Mount Lamp Inoperative
  • Fuse.
  • Circuit.
  • Brake pedal position (BPP) switch.
  • GO to Pinpoint Test Step K1 .
  • One or More Stoplamps Inoperative
  • Stoplamp bulb(s).
  • Circuit.
  • GO to Pinpoint Test Step L1 .
  • Stoplamps/Rear Hi-Mount Lamp On Continuously
  • BPP switch.
  • REPLACE the BPP switch.


f4078b8.gif

Apr 20, 2009 | 1998 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

554 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...