Question about Chrysler Town & Country

1 Answer

The rh turn signal will not flash on the front or back of the vehicle. You can hear the flasher in the dash clicking at the normal rate. The lh side works fine.

Posted by on

  • cjs45lj Sep 17, 2010

    Sorry Coach. Didn't mean any such thing as you supposed but you gotta admit that checking the bulbs is pretty darn simple, Even if you want to suggest that it should be done you wasted my time by not suggesting something else just incase I wasn't a moron and couldn't figure out that I should check the bulbs before asking you or anyone else for help! Get a grip pal! Next time include another step besides something so trivial as "Sounds like a bulb to me!!!" Duh!!! You deserved a mark for that! Grow up already!, Hateful my a--! I'll tell you this, I got this one figured out! Prove that you are what you claim and tell me what fixed it! Telling me you think it's a bulb makes me doubt you really know what you are talking about.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 385 Answers

That sounds like a blown bulb on that side

Posted on Sep 13, 2010

  • 1 more comment 
  • cjs45lj Sep 14, 2010

    Both the front and back bulbs were replaced with no change to the problem.

  • John Does Sep 16, 2010

    you're a ****. you give me a bad rating and hurt my profile? all I was trying to do was help you, you hateful loser. I could still help you, but I won't.

  • John Does Sep 17, 2010

    I don't have to prove **** to you. I have 4 ASE certifications and more than 10 years experience in solving auto problems. And in case you haven't noticed some of the posts and problems on this site, there are a lot of morons that ask stupid questions while offering very little preface info. Like "turn signal on one side doesn't work. Oh my! What should I do?" Without even offering that they changed out the bulbs, or checked or replaced the turn signal flasher, or removed some of the dried up grease from the overpacked pigtail socket that the manufacturers typically do because it's the cheapest way to keep moisture out long term. It's unappreciative jerks like you that make this site the ******** it is....

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

Right blinker not working 1999 Buick park avenue


You'll need to find a wiring diagram an component location chart to check this out . Here is a diagnostic flow chart for trouble shooting this problem ! Do you know how to use a voltmeter ?
DEFINITION: This table diagnoses inoperative turn signals on one side. It assumes that the cornering lamps, hazard lamps, and turn signals on the other side all operate properly.

1

Did you perform the Exterior Lights System Check?
--
Go to Step 2 - yes
Go to Exterior Lights System Check - no

2

  1. Disconnect the turn signal flasher connector.
  2. Turn the ignition switch to the RUN position.
  3. Place the turn signal switch in the appropriate position.
  4. Connect a DMM from the appropriate turn signal flasher connector cavity to ground:
?€¢
LH: cavity C (ORN)


?€¢
RH: cavity B (BLK)

Is the voltage within the specified range?
10-15 V
Go to Step 3 yes
Go to Step 5 no

3

Connect a fused jumper between the appropriate turn signal flasher connector cavities:
?€¢
LH: cavity C (ORN) to cavity D (YEL)


?€¢
RH: cavity B (BLK) to cavity F (TAN)

Do the appropriate turn lamps light without flashing?
--
Go to Step 4 yes
Go to Step 6 no

4

Replace the turn signal flasher. Refer to Hazard and Turn Signal Flasher Replacement .
Is the repair complete?
--
Go to Exterior Lights System Check
--

5

Repair the open in the appropriate circuit:
?€¢
LH: CKT 57 (ORN) between S200 and the turn signal flasher


?€¢
RH: CKT 58 (BLK) between S201 and the turn signal flasher

Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
--
Go to Exterior Lights System Check
--

6

Repair the open in the appropriate circuit between the turn signal flasher and the IP fuse block:
?€¢
LH: CKT 685 (YEL)


?€¢
RH: CKT 686 (TAN)

Refer to Wiring Repairs in Wiring Systems.
Is the repair complete?
--
Go to Exterior Lights System Check

May 09, 2015 | 1999 Buick Park Avenue Ultra

3 Answers

My left turn signal started to only work about 50% of the time, it wont work hardly at all now. the right turn signal is fine. When I try to use the left turn signal, there is no dash indicator lights


Hey Bob how's it going ? I have been looking at Chevy service info for your vehicle and this a little on the complex side or that is the way it sounds from the turn signal description !
Turn Signal Lamps
The smart flasher (GMSF) is an automotive flasher designed to accept turn, hazard, and brake inputs. The GMSF will provide corresponding outputs to the exterior lamps and instrument panel turn signal indicator lamps. This lighting system has dedicated lamps for the turn/hazard functions and dedicated lamps for the brake function. The system incorporates the use of flash rates for diagnostics. The flash rate is a calculation of the number of flashes that occur within a 60 second period. This system uses a percentage of on-time to off-time called duty cycle. For the bulb outage condition, the indicator of the vehicle side on which the outage occurs shall assume bulb outage flash rate mode. The opposite side indicator will assume the normal flash rate mode for an input from the non bulb outage side of the vehicle. Hazard warning lamp outage will maintain a normal flash rate as long as 2 or more exterior signaling lamps are functional. During all modes of operation, the IPC will receive the same flash rates and duty cycles that the exterior lamps receive. The IPC will then control the indicators in the cluster. The vehicle operator will be provided with an audible and visual indication of the flasher operation. Below is a table with flash rates and duty cycles:
Are all your bulbs good ?
Operating Condition
Flash Rate
Duty Cycle
Normal
75 to 105 flashes per minute
45% to 55%
Turn Signal Lamp Outage
2 or 3 times faster than normal flash rate
35% to 55%

Feb 02, 2015 | 2005 Chevrolet TrailBlazer

1 Answer

Turn signal failure


The bulbs all have to be good for the flasher to work. The flasher is under the dash, driver side. When you turn on a blinker, do you hear it clicking under the dash. If the turn light is on , on the dash , but not flashing, then a bulb is probably bad on that side. Leave the blinker on and walk around the vehicle to check the lights. Flip the blinker to the other side and walk around the vehicle again checking lights. If all the lights are lit, but not blinking, then the flasher is most likely bad.

Dec 05, 2013 | 2000 Chevrolet Venture

1 Answer

Turn signal lights not working. turn on emergency flashers and the right signal flashes and bath back lights and the front right flash but the left front don't. any idea's


The 2 filament on the LH Front turn signal is most likely burned out, ...........or the ground to it, & the entire socket needs replaced. Caution lights, send signals to ALL FRONT & REAR lights. All turn signal lights must be in working order, as it is a "pulsating" currect surge sent to the bulbs, LH or RH, depending which direction you wisk to turn. If 1 filament is broken, the circuit is incomplete, & no flash will occur. Usually you will get one light that stays on, & the front or rear missing lighting, is the one whichis the culpret.

Aug 29, 2011 | 2001 Ford F150 Styleside SuperCrew

1 Answer

How do i remove instrument panel cluster on 98 towncar


Removal
  1. Remove the steering column
  1. Remove the passenger side air bag module
  1. Position the speed control servo aside.
    1. Remove the nuts.
    1. Position the speed control servo aside.
    gr2792a.gif
  1. Disconnect the LH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the LH bulkhead connector.
    gr2793a.gif
  1. Unclip the LH bulkhead connector from the dash panel.
    gr2794a.gif
  1. Remove the windshield washer reservoir
  1. Disconnect the blower motor electrical connector.
    gr2795a.gif
  1. Disconnect the A/C pressure cut-off switch electrical connector.
    gr2796a.gif
  1. Disconnect the in-line wiring harness connector.
    gr2797a.gif
  1. Disconnect the electronic automatic temperature control (EATC) variable blower motor controller electrical connector.
    gr2798a.gif.
  1. Raise and support the vehicl
  1. Remove the RH front wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the RH front wheel and tire assembly.
    gr2845a.gif
  1. Remove the front fender splash shield bolts.
    gr2800a.gif
  1. Position the front fender splash shield away from the dash panel.
    gr2801a.gif
  1. Unclip the wiring harness from the evaporator case.
    gr2802a.gif
  1. Unclip the wiring harness from the dash panel.
    gr2803a.gif
  1. Lower the vehicle.
  1. Lower the RH instrument panel lower insulator.
    1. Remove the pushpins.
    1. Lower the RH instrument panel lower insulator.
    gr2805b.gif
  1. Remove the RH instrument panel lower insulator.
    1. Disconnect the power point electrical connector.
    1. Remove the courtesy lamp from the lamp socket.
    1. Remove the RH instrument panel lower insulator.
    gr2806a.gif
  1. Unseat the wiring grommet and feed the wiring harness through the dash panel.
    gr2804a.gif
  1. Remove the LH and RH cowl side trim panels.
    gr2807a.gif
  1. Remove the LH and RH windshield side garnish moldings.
    gr2808a.gif
  1. Disconnect the electronic crash sensor (ECS) module electrical connector.
    1. Disconnect the locking clip.
    1. Disconnect the electrical connector.
    dr0308a.gif
  1. Disconnect the antenna cable in-line connector.
    gr2809a.gif
  1. Remove the RH ground bolts.
    gr2810a.gif
  1. Disconnect the EATC hose from the evaporator housing.
    gr2811a.gif
  1. Disconnect the RH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the RH bulkhead connector.
    gr2812a.gif
  1. Position the LH and RH door weatherstrip seals away from the instrument panel.
    gr2813a.gif
  1. Remove the tunnel brace trim cover.
    gr2814a.gif
  1. Disconnect the climate control head vacuum harness connector.
    gr2815a.gif
  1. Remove the instrument panel tunnel brace.
    1. Remove the nuts.
    1. Remove the instrument panel tunnel brace.
    gr2816b.gif
  1. Remove the LH ground bolts.
    gr2817a.gif
  1. Disconnect the LH wiring harness connectors.
    gr2818a.gif
  1. Disconnect the parking brake switch electrical connector.
    gr2819a.gif
  1. Remove the instrument panel defroster opening grille.
    1. Unclip the instrument panel defroster opening grille from the instrument panel.
    1. Disconnect the electrical connectors.
    1. Remove the instrument panel defroster opening grille.
    gr2820a.gif
  1. Remove the three instrument panel cowl top screws.
    gr2821a.gif
  1. Remove the RH instrument panel cowl side nut.
    gr2822a.gif
  1. Remove the upper LH instrument panel cowl side nut.
    gr2823a.gif
  1. Remove the lower LH instrument panel cowl side bolt.
    gr2824a.gif
  1. NOTE: Removing the instrument panel from the vehicle requires two technicians.
    Remove the instrument panel from the vehicle.
    gr2879a.gif

Mar 07, 2011 | 1998 Lincoln Town Car

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

Still no turn signals...


The Electronic Flasher is located behind LH side of the instrument panel, above fuse panel.
you have to get on your back in front of the drivers seat ,,,with a flash light and look under the dash ,,, on the left side of the steering column tucked under the dash is a black square relay looking thing ,,this is your turn signal flasher ,,

Jun 05, 2017 | 1993 Ford Taurus

4 Answers

Front driver side turn signal light doesn't flash.replaced bulb,replaced socket,all other lights work on emergency flasher,except front driver side.rear driver side turn signal light works,but flashes...


replace flasher......usually located in fuse block area...listen in this area....select passenger side ...then select driver side...you can hear flasher clicking...you have seperate flashers for each...FLASHERS are small cubes plugged into fuse block....probable bad driverside flasher

May 09, 2009 | 1998 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...