Question about 2001 Chrysler Prowler

1 Answer

Price on a 1995 ertl 1/18 plymouth prowler concept vehicle

Need to find a price on a 1995 ertl 1/18 plymouth prowler concept vehicle.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,010 Answers

Need to find a price on a 1995 ertl 1/18 plymoutCheck eBay.com to see if there are others out there. Put them on your watch list and you should get a good idea of what they are going for.h prowler concept vehicle.

Posted on May 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the trans filler?


It has a filler tube:

How do you add transmission fuild to a Plymouth prowler

www.answers.com > ... > Plymouth (car) > Plymouth Prowler
Simply pull the handle out of the trans fuild filler port in the engine ... produced from1999 to 2001 as the Chrysler Prowler when Plymouth was dropped in 2001.

Nov 06, 2015 | 1999 Plymouth Prowler

1 Answer

Need to see a photo of the motor mount support assembly


You can buy them form vehicle dismantlers/wreckers.

Dec 25, 2012 | 1995 Plymouth Acclaim

1 Answer

1995 plymouth acclaim-hight idle/where and how do I get to the ilde(high) screw? Thank you.


A 1995 Plymouth Acclaim is a fuel injected vehicle which means it does not have an idle screw like the older carbrated cars. Instead your cars idle is controlled by sensors and the cars on board computer. There is a chance you either have a bad sensor or a vacuum leak some where. Both will cause a high idle. I hope this helps you out.

Aug 25, 2011 | 1995 Plymouth Acclaim

1 Answer

1995 Plymouth Neon no electrical power. I have had my battery tested - output is normal. is there a master fuse or fusable link?


It could be something as simple as you have corrosion on the clamps connecting to battery cables to the battery posts. If you do you will not get a clean connection therefore you will get no power to the vehicle. I have noticed over the years chrysler vehicles tend to have a prob with corrosion around the posts especially on the neg terminal.

Nov 27, 2010 | 1995 Plymouth Neon

1 Answer

1995 plymouth voyager transmission does not shift higher then 2nd gear unless warm?


Potential problem - useful life of that transmission is about 120k. Have you noticed any drip under the vehicle coming from the trans area? Make sure the fluid level is correct and check with a transmission shop. They can put a scanner on and check for codes.

Feb 25, 2010 | 1995 Plymouth Voyager

1 Answer

Dodge prowler


Cooling system problems are easy to fix as there really is only a few things that actually regulate the temp. Your thermostat is more than likely stuck half open. That would explain why its ok at night but not during the day.

Do your cooling fans come on? If they do and seem to be at least trying to do their job my solution would indeed be your best bet. Make sure your fans come on when the temp gets high, otherwise you may have a bad fan relay.

Aug 14, 2008 | 2001 Plymouth Prowler

1 Answer

Remove the rear bumper


Removing Prowler Rear Bumpers First remove the four 10 MM bolts holding the trans cooler and drop it down. Support it by attaching one bolt to the lower hole on the cooler frame. This will keep the weight off the lines. This takes two min. and allows easy removal of the elect. lines. Then remove the four bolts on each bumper. The bolts are 13MM and 17MM. You will need a ratchet, sockets, extension and a 13MM open end wrench. If you remove the rear bumpers, you should replace the rear pan with one of the aftermarket ones otherwise you will have big holes staring at the people behind you. Go to prowleronline.com and check the vendors for a couple of options. Maybe you are removeing them to paint and reinstall. Look at this link for some options .. Mine is the 7th post down. http://www.prowleronline.com/ubb/Forum1/HTML/014949.html Hope this helps.

May 15, 2008 | Plymouth Prowler Cars & Trucks

Not finding what you are looking for?
2001 Chrysler Prowler Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...