AIRBAG LIGHT ON CODE 4 blinks then 5 blinks then stays ON

The light will only quit flashing if there is no problem, So you must have a problem. Do this get to the diagnostic mode only this time count the flashes these are codes, it will look like this example a flash followed by Two fast flashes is code 12, Three long flashes followed by Three short or fast flashes is code 33. When you get the code use the testimonial to tell me what they are. It will show up in my email. I hope this helps. Take care.

what is causing my airbag light, abs light and battery light to ...

https://answers.yahoo.com/question/index?qid...
Jul 12, 2014 - My battery light stays on sometimes it might blink on and off. But the problem is i can be driving my car and my airbag light and abs light will ...

Electrics HELP! Engine management light, Brake, Airbag, ABS, EPS ...

www.civinfo.com > ... > Bugs, faults and irritations
Feb 12, 2012 - 18 posts - ‎5 authors Airbag light. ABS ALSO - the speedometer, rev counter and engine temp ... 30 mins driving (apart from engine management light which stays on). ... I have ruled out problems with the alternator and the relays - they're all fine.

airbag abs srs light diagnose without a scanner air bag ...

? 4:14
www.youtube.com/watch?v=tIBjIr9a42w
Feb 6, 2010 - Uploaded by vehix411 airbag abs srs light diagnose without a scanner air bag ... Alsowhen I tried the scan plugging the paper ...

The flashing light on your car is telling there is a problem. On some vehicles require a OBD2 code scanner for the diagnosis. Once you know the code, you can most likely repair it yourself.

Guys! Are you readying your airbag system after messing around with your truck?

I've seen airbag lights come on for man reasons, faulty sensors, connections, replacing RADIOS! Removing seats!! All sorts of reasons. Personally I bought my QX56 with the airbag light blinking. Drove me crazy for 24 hours till I decided to reset it n see what happened. It takes two minutes to do. No tools.

1. Turn key from off to on. (on meaning all your dash lights are on but your not cranking the motor)

2. Watch the airbag light closely. It will stay on for a few secs. and then as soon as it blinks off (the start of the flashing), turn the key off instantly.

3. Count to 5 (1 Mississippi, 2 Mississippi . . . .)

4. Repeat steps 1-3 two more times until you have done the cycle three times.

5. Now turn the key on and watch the light. It will start blinking in a different, slower manner. This is diagnostic mode. You can watch this for a little while, no hurry.

6. Now turn the key off again, Count to 5 like in step 3 again, and turn back on. If the procedure worked, the airbag light will not be flashing.

"If you have the airbag light, it will show steady for a few seconds (the manual says 7 secs) after you turn the key from off to on (but not start) and then start to flash. Here is how to reset it:

1. Turn the key from off to on.

2. Watch the airbag light closely. It will stay on for a few secs. and then as soon as it blinks off (the start of the flashing), turn the key off instantly.

3. Count to 5 (1 Mississippi, 2 Mississippi . . . .)

4. Repeat steps 1-3 two more times until you have done the cycle three times.

5. Now turn the key on and watch the light. It will start blinking in a different, slower manner. This is diagnostic mode. You can watch this for a little while, no hurry.

6. Now turn the key off again, Count to 5 like in step 3 again, and turn back on. If the procedure worked, the airbag light will not be flashing.

If it does not work the first time, just repeat the steps again."

When you turn on the ignition switch does the light flash and then stay steady on?

If it's flashing it could indicate the fault code. By instance, two long followed by 5 short blinking will indicate an error code 25

The same code may be repeated before the light stay on.

By the way, any changes or repairs done recently on your vehicule?
Let us know if you get additional information
Hope it will help
Dan

If you mean the passenger airbag light no longer lights up and airbag light on the dash blinks at start-up and then stays on; the read the below and check this site:

www.automotivehelper.com

I went to radio shack cost me $2.99 for 3 bulb packet. But the post below worked. It really didn't that long, pretty easy job. Took longer to find the tools. The first guys idea/fix, the second guy gave pretty good instructions. Just a little more detail: (3) the clips are one each side of the panel; (5) these two screws are on the inside lower part of module, (6) unclip the plastic tabs from the back (where the plug end is) first and it should lift up easily.

-------------
I had this happen on my 98 Ranger.(code 27) My light on the module that turns off the passenger side airbag was burnt out. I went to Radio Shack and bought a 12v light with wires attached and soldered them to the existing light.(didn't even take it out!) It fixed it!! Cost, about $1.50 and 20 minutes of fix time.

Note: If the light by the key switch to turn off the passenger side airbag does not work, it disables the entire airbag system! Hope yours is as easy to fix.

----------

gerg,

Thanks for your post. I have no way to read codes, but I heard the five tone alarm every time I started the vehicle and the passenger air bag off light did not light up. I was skeptical, but tried your advice and it worked.

Parts:
1) 12-volt colored lamp (Radio Shack part: 272-1099)

Tools:
1) socket set
2) philips head screw driver
3) soldering iron

Procedure:
1) remove ash tray from console panel
2) using a socket set, remove 4 hex head screws from console panel
3) pull console panel out of the two clips
4) remove connector from air bag key module in console panel and take console panel to a work bench
5) remove 2 philips head screws to remove the airbag key module
6) carefully unclip the plastic tabs that hold the airbag key module case together
7) remove connector circuit board from air bag key module
8) solder the yellow replacement lamp to the two solder pads for the original lamp on the back side of the circuit board (which wire to which pad does not matter)
9) tie the replacement lamp in place next to the original lamp
10) replace the circuit board in the airbag key module and snap the case back together
11) connect the airbag key module in the truck and start the engine to check that the lamp illuminates and that the alarm does not sound
12) screw the aribag key module back into the console panel
13) snap the console panel back into the truck
14) replace the 4 hex head screws
15) replace the ash tray

The blink code you are refering to is : Intermittent or Repaired RH Radiator Primary Crash Sensor Feed/Return Circuit Open , which means your right hand side frontal crash sensor (airbag sensor) is not working, therefore your airbag system is disabled...

my airbag light is blinking . can i reset anything its a04 nissaun armada

Take it to an independent specialist mechanic to get the codes read and a suggested plan of action