Question about 1988 Mazda 626 Turbo

1 Answer

How to release the centre lamp (door lamp), no bolt there,, so from where can i do first. im so affraid if the plastic cover is break when i forced to open it.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Contributor
  • 613 Answers

They are clipped inside the light so have to use little flat head screw driver to pop it open if old brittle may break but only way to replace the bulb

Posted on Sep 13, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove the cover on the inside door light of a 1999 ford f-150

Door lights are supposed to come on when you open the door.
The covers are usually secured by little plastic tabs protuding from ths long sides. Gently squeeze one side towards the centre and the cover should come out easily. Don't try to force it if it argues with you.

Mar 16, 2015 | Ford Cars & Trucks

1 Answer

Disassemble connection on wiring harness between the two door hinges on front door of mynissanpulsar 1998 sss I need to remove the bolt that connects the harness to the door it's got two pins holding

nissan forenza? swap?
im not sure what car,
solder wires,
post a photo (no really, im blind)
or read the book, at

my wild guess is you mean the door limiter device.
it has pins, , you use pin press to press them out.
or a c-clamp and a socket (3/8" say 1/2 hex) as a spacer?
eg: make your own press..
no photos, no joy here. its Physical , hands on , eyes on , world.

Dec 01, 2013 | 2005 Suzuki Forenza

1 Answer

How do i release the spare tire on my 2005 Kia Sedona

Hi, the spare tire is stored on the underside of the vehicle, under the right-side cargo door. The bolt is located in a recessed area that is protected by a small square plastic covering. To remove the spare tire, find and remove the bolt cover, then use your lug nut wrench to loosen the bolt holding the tire.
Remove the spare tire fastener's plastic cover, place the lug nut wrench onto the lug nut holding the tire onto the bolt, turn the wrench in a counter-clockwise direction until the tire is released and reaches the ground.

Jun 20, 2011 | 2005 Kia Sedona

1 Answer

How do you install a driver seat plastic shield on a 2004 Ford Explorer? Its the piece of hard plastic between the door and the seat - part number 1L2Z-7862187-BAC

see if this helps
  1. Remove the rear trim screw.

  1. Remove the lower trim screw.

  1. Release the side trim front retaining clip.
  2. Pull the lumbar mechanism out slightly from the seat.
  3. Push down and pull out, releasing the side trim front retaining clip.
  4. CAUTION: Take care when removing the side trim cover. Excessive force will break the mounting tabs.

Release the side trim from the mounting bracket.

  1. Disconnect the seat control switch electrical connector.

Mar 25, 2011 | 1998 Ford Explorer

2 Answers

Rear door glass fell down, will not wind back up.

do not force anything ,remove the door panel and have a look then post if you need more help ,but it sounds like the either the clamp or the support is loose or corroded away

May 30, 2010 | 2000 Jaguar S-Type

1 Answer

Replace drivers side mirror on 94 s-10

Take off door has plastic retainers so give it a good yank. May have to take screws out of arm rest and be easy with the door handle not to force it and break. The mirrow will be held on with a couple bolts/perty easy once you get the cover off..

Dec 17, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

Replacing front headlight bulb . Instructions for

With the hood open, you will see a long flat flexible plastic cover running across the front, above the headlights. It is riveted in with plastic rivets. Hold the outer part of the rivet, and pull up the center part. Then remove the whole rivet. Remove the plastic cover. (When you put it back on, insert the outer part in the hole, then press the center part down into each rivet.)
You will see a sidelamp and headlight assembly. Look down between the sidelamp and headlight, there should be a black plastic clip or latch that holds the side lamp to the headlight. (The clip is down a hole, in the bracket holding the headlight to the body). You will probably need a long screw drive to get down in the hole to release the clip. And maybe a flash light to see down the hole. Put just enough pressure to release the latch, it is plastic, and if you press to hard it could break. Once released the side lamp will pop forward a bit. The sidelamp section can be pulled forward. a bit. However, there is a long plastic part on the Sidelamp Section that slides into a metal hole in the Fender. It will break if you try to pry the sidelamp section out sideways.
Next you will see two top-mounted bolts holding the Headlight Assembly in place which can easily be accessed and removed. Removing the bolts will loosen the entire headlight assembly.
Some instruction say you can remove the headlight and side assembly as a unit. Do not do this! If you try to remove the headlight assembly without detaching the sidelamp you could break either of the lights or the connection assembly.
The Bulb Assembly twists out of the back of the Headlight Assembly, and the bulb can then be replaced. Be careful not to touch the bulb with your hands or with any grease.
Many of the parts are plastic and can break, so do this carefully and patiently. It sounds a little complicated, but once you learn how, the whole job only takes about 20 minutes.

Hope helped. (remember rated this).

Oct 19, 2009 | 2002 Chevrolet Cavalier Coupe

1 Answer

Rear windscreen wiper V70 1998

Pull, and the plastic clips will disengage.  Some will break, there is nothing you can do about that.  Best to make a run to the dealer and pick up a handful of extra clips for the ones that do break.  There are tools that help prevent the clips breaking but they'll still break and it's not worth it.

Aug 08, 2009 | 1998 Volvo V70

1 Answer

Hard to remove plastic cover over the air filter.

remove the 2 bolts securing plastic case u see first then look under cover youll see the filter housing open and replace dont forget to attach all the clamps and hoses u removed

Apr 07, 2009 | 2000 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides