Question about 1994 Toyota Previa

1 Answer

How do i replace spark plug leads on ditributor cap

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 834 Answers

Here is a firing order diagram to help assist you.

how do i replace spark - 7611502.jpg

Posted on Sep 13, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I mixed up which of the plug wires go to the ditributor cap. How can I tell from bottom to top which one goes to which spark plug?

Take out number one plug, make a wad of paper and put it just in the plug hole. Turn the engine by hand until it pops out, the engine is just about to fire on number one cylinder. Take off the distributor cap and see where the rotor is positioned, move the engine slowly and watch the points. When they just open that is the position of the number one plug lead on the cap. Firing order 1342, go around the cap with the other leads.

Jul 26, 2011 | Oldsmobile Cutlass Ciera Cars & Trucks

2 Answers

1979 ford f350 has no spark. replaced coil, plugs, ignition module and still no spark. please help!

1979 ford 400 Drove inot shop did a cam shaft change and put all back together and no spark! put new coil , distributor, eletronic brian , wires ,rotor, cap, and check wire harness for brroken wires . still no spark? ANY IDEAS??

Jan 12, 2011 | 1979 Ford F 350

2 Answers

I have changed ditributor cap spark plugs for my mazda626 92,v36,2.5. after i started its misfiring and i think its not burning the fuel,can see smoke coming from the i try to rev up the rpm...

Make sure the spark plugs are properly gapped (this will cause misfires). Replace all spark plugs wires!! Insure there is no oil inside the spark plug chamber.

Oct 06, 2010 | 1992 Mazda 626

1 Answer

Changing spark plug wires

The best way is to replace one wire at a time. Grab each wire boot and twist back and forth to break loose the sealing to the plug, and pull off. When reinstalling, make sure that all wires are seated in the ditributor cap, they can be a little tough to get seated properly.

May 26, 2010 | 1996 GMC Sonoma

1 Answer

How change spark plug wire

alot of the 4 cyl vehicles spark plug leads are joined to distributor cap and come as complete assembly leads and cap.the new leads have cylinder numers on them and/or on dissy cap.
twist and pull to remove leads out of haed(spark plugs),remove 3 screws from dissy cap and replace.

Feb 15, 2010 | 1996 Toyota Corolla

1 Answer

How do you test the distributor on the 2000 Xterra? Is there a diagram that explains what the voltage in or out should be?

hi testing a ditributor is usualy done visualy.. you can atatch a lead to the dizzy and the attatch a dummy spark plug, you can get them from auto shops, when you turn the engine over the plug will spark, and you can determine quality of the spark by how bright it is, you can test leads with a multimetre useing ohms for resistance and the leads should have a spec written on them, be carefull not to touch anything when the engine is being turned over because the current can be potentialy fatal

Feb 10, 2010 | 2000 Nissan Xterra

1 Answer

What is the spark plug gap for 1991 nissan 240 sx and can I find a diagram for the wire harness to the ditributor cap

if you have a 1.6 engine the gap is .041 ths /(1.04mm) if you have a 2.0 engine the gap is .033 ths / (.84mm)

May 30, 2009 | 1991 Nissan 240SX

1 Answer

Car runs for 5 mins then cuts out

check to see if it is a crankshaft sensor if applicable to this model.if not check to see if it is an electronic distrubutor.

Oct 14, 2008 | Ford Laser Cars & Trucks

Not finding what you are looking for?
1994 Toyota Previa Logo

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides