Question about 1998 Mazda 626

1 Answer

How do i replace brake pads for 1998 mazda 626

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 235 Answers

Get a Chilton's manual for your vehicle and knock yourself out.

Posted on Sep 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

!998 Mazda 626 4 cylinder standard shift. After driving the vehicle for a while (10 miles or so) front brakes are getting hot to the point when stopping the vehicle will hardly move. The brake pedal also...


last one before bed in this time zone ,the problem is the master cylinder serco push rod needs adjusting ,undo teh two nuts holding the master cylinder on and where it bolts onto the servo is a rod poking out of the servo well this rod has an adjustment on the end ,screw it it a bit so it has some free play then brakes will not lock up .someone has adjusted it to make the brakes feel tighter and over adjusted it out wards too much not allowing for the fluid expansion when it gets warm .

Jan 27, 2011 | 1998 Mazda 626

2 Answers

I have a 1998 mazda 626. I just had the brakes and roters replaced on the front end and now my cruise control will not even turn on. Is this problems related to the brakes or do you think it is something...


probably not. Once you find and correct the problem then you will know if it was related or not. Check the fuse and the brake switch, that's the most common things.

Nov 22, 2010 | 1998 Mazda 626

2 Answers

Mazda 626 handbrake light comes on when I touch brakes


It's your disk pad wear indicator warning you of imminant replacement of pads . They ground electrically thru contact in brake pads and require attention. If light goes out it's not a level problem and cheap replacement .

Apr 05, 2010 | 2002 Mazda Protege

1 Answer

ABS brakes not working


If you can feel the pedal pulsating and the light turns on the Abs is doin its job. if you want a better stop you could try a brake pad upgrade to ceramic pads and for even more stoping power add an after market drilled and sloted rotors.

Feb 28, 2010 | 1998 Mazda 626

1 Answer

Back rear brakes metal to metal sound


I would not doubt that it is from aftermarket parts.

Use silicon grease on the caliper slides and use brake grease on all metal to metal contact parts when installing the new parts.

Also, grind away any rust where the pads sit on the caliper bracket before installing them.

May 18, 2009 | 1998 Mazda 626

2 Answers

How to change out front brake pads on a 2001 mazda 626?


remove 2 caliper bolts, remove old pads. put new pads in there place, before installing the caliper, be sure to squeeze the piston back in the caliper otherwise it will not fit back over the new pads. than replace the caliper and the 2 mounting bolts.

May 07, 2009 | 1995 Mazda 626

1 Answer

CHANGING REAR BRAKE PADS


the best thing you can do is go to an autoparts store and purchase a haynes repair manual for your car. cost about $18, but will show you everything you need to know, with pictures.

Nov 28, 2008 | 1998 Mazda 626

1 Answer

Mazda 626 1998 brake lights not working


A- AT BRAKE PEDAL-CHECK FOE WIRES LEADING TO SWITCH, IF CON.IS OK,PRESS DOWN ON PEDAL, WATCH PLUNGER ON OPOSITE END. IF OPERATING COR. CHECK FUSE. TURN SIGNSLS OK,EMG SIGNSL OK?

Oct 08, 2008 | 1998 Mazda 626

1 Answer

Brake Problem


hi im dave
hope i can help
when you had the rear pads applied and the discs turned was there noticeable damage to the disc surface it sounds like your e brake cable is not adjusted properly or perhaps the braided wires inside the insulation are seperating along your brake cable causing the rear brakes to not be adjsting themselves properly. Every time the parking brake is applied the rear brakes are self adjusted if they arent being applied due to slack in or a broken cable you will not adjust your rear brakes. This would accont for the flutter in the brake pedal as hydraulic fluid is still circulating to compress the pads against the rotor but the pads arent reaching the rotor.

Jun 22, 2008 | 1998 Mazda 626

Not finding what you are looking for?
1998 Mazda 626 Logo

Related Topics:

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...