Question about 1995 Honda Civic

1 Answer

Help me with removing my oil pan

Help me remove my oil pan the exhaust is in the way

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,035 Answers

I highly recommend having a torque wrench at your disposal to perform this procedure. Hondas go forever if you take care of them, a torque wrench is a small investment (and some auto parts stores will loan/rent them to you).

According to the manual (for the 1998 - the 1996 is probably the same) you will first need to remove the transmissioin/engine stiffener. This is a piece that transverses from the engine to transmission and is held in place by 4 bolts.

After that you remove the existing oil pan.

You must scrape off any residue or remaining gasket from the engine block - you can do that with a putty knife. Be careful not to scratch/gouge the surface. Then clean the surface of the engine block.

Get a new pan and gasket. Use gasket seal (Honda part # 08718-0001 ir 0718-0003) to afix the gasket to the pan. According to the manual, after affixing the gasket you should use additional gasket seal at both of the short ends of the (more or less) rectangular outline of the pan/gasket (including the rounded corners) and then put them on to the block (do this within 5 minutes of applying the gasket seal). The manual indicates you should hand tighten six bolts - the ones at the corners of the short ends of the rectangle, and the ones right in the middle of the long ends. When these are hand tight you will insert and hand tighten the other bolts. Then increasingly tighten the bolts starting with the one most directly under the oil filter. Work from that bolt clockwise, gradually increasing the tightness of the bolts until you reach a torque of 8.7 foot pounds.

If you don't do this correctly you will warp the pan, so be careful.

Once completed you should refasten the engine stiffener. The bolts going to the engine side should be tightened to 17 foot pounds, the bolts to the transmission side should be tightened to 33 foot pounds.

You should be done, but the manual says to wait 30 minutes prior to adding oil.

Good luck!

Posted on May 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the oil pan on a 1996 honda accord


First you must remove the A exhaust pipe that is under the oil pan. Make sure use a penetrating lube, like WD-40 on all exhaust nuts. If there is a lot of rust, you can remove the 3 or 4 manifold nuts, the 2 bolts for the bracket to the block, and unhook the exhaust hangers, and move the whole exhaust out of the way. Drain the oil, then remove the support brackets, then all the 10mm oil pan bolts and nuts. The oil pan can seem glued in place, pry it loose without bending it. Make sure you get any steel rings off from around the studs, they are part of the oil pan gasket, and tend to stick to the block.

Oct 05, 2014 | 1996 Honda Accord

1 Answer

How to remove oil pan


Remove the exhaust pipe "A" first. don't forget to put a lube, like WD40 on all the exhaust studs, nuts and bolts before loosening them. Drain the oil and unbolt the oil pan, (18?) 10 mm bolts. The pan will need to be pried loose.

Apr 22, 2014 | 2006 Honda Pilot

1 Answer

How do you get the oil pan off of a 2006 dodge stratus 2.7L


Hope this helps and please don't forget to rate!


  1. Disconnect the negative battery cable.
  2. Remove the engine oil dipstick and tube.
  3. Raise and safely support the vehicle.
  4. Drain the engine oil and remove the oil filter.
  5. Remove the structural collar.
  6. Remove the exhaust cross-under pipe.
  7. Remove the torque converter housing cover.
  8. Remove the lower bolt attaching the A/C compressor to the oil pan.
WARNING!!!!!
Be sure to remove the 2 bolts attaching the timing cover to the oil pan, as damage to the timing cover and/or oil pan may occur.
  1. Remove the oil pan attaching fasteners.
  2. Remove the oil pan and gasket.

May 08, 2011 | 2006 Dodge Stratus

1 Answer

How to do an oilpan on a 88 chevy montecarlo


  1. Disconnect battery negative cable.
  2. Remove air cleaner.
  3. Remove upper fail shroud (V8)
  4. Raise vehicle and drain oil pan.
  5. Disconnect A.I.R. hose at converter pipe (V8)
  6. Disconnect A.I.R. pipe at exhaust manifold (V8)
  7. Remove exhaust crossover pipe at manifold and converter.
  8. Remove starter.
  9. Remove flywheel cover.
  10. Disconnect transmission oil cooler lines at oil pan.
  11. Remove engine mount 'through' bolts on V8. Loosen right bolt and remove left on V6.
  12. Remove oil pan bolts and lower oil pan. Check that forward crankshaft throw and/or counter balance weight are not extending downward so to block oil pan removal. Turn crankshaft, necessary, to put throw on horizontal plane.
  13. Raise engine.
  14. Remove oil pan.
Installation


  1. Clean sealing surfaces on cylinder case and pan.
  2. Check oil pan gasket for damage; replace if necessary.
  3. Apply a small amount of 1052751 or equivalent to front and rear corners of oil pan.
NOTICE: Only a small amount of sealant is required. Excessive amounts of sealant may cause a problem with proper sealing of oil pan.


  1. Install retaining bolts and torque to 9 N.m (80 lb. in.).
  2. Raise engine, if necessary.
  3. Lower engine, install mount 'through' bolts and torque to 50 lb. ft. (65 N.m).
  4. Install torque converter cover.
  5. Install starter.
  6. Install exhaust crossover pipe at manifold and converter.
  7. Lower vehicle.
  8. Install fan shroud.
  9. Install air cleaner.
  10. Fill crankcase with oil.
  11. Connect battery negative cable, start engine and check for leaks.

Nov 30, 2010 | 1987 Chevrolet Monte Carlo

1 Answer

Have a 1999 eclipse 2.0 L...Need to replace oil pan. Do I have to remove any other parts to get the pan off


2.0L Engine
  1. Disconnect the negative battery cable.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine undercover Front exhaust pipe Lower oil pan bolts and lower pan Cover Upper oil pan bolt and upper pan Baffle plate

    0996b43f8023193a.jpg Fig. Oil pan and related components-2.0L engine

To install:
  1. Clean all gasket surfaces of the cylinder block and the upper and lower oil pan.
  2. Install or connect the following:
    Baffle plate
  3. Apply a 0.16 in. (4mm) bead of sealant to the gasket surfaces of the upper oil pan.
    Upper oil pan onto the cylinder block within 15 minutes after applying sealant. Tighten the bolts as shown in the accompanying figure.

    0996b43f8023192d.jpg Fig. Upper oil pan bolt location and torque sequence-2.0L engine

  4. Apply 0.16 in. (4mm) bead of sealant to the gasket surfaces of the lower oil pan.
    Lower oil pan and tighten the bolts, in the sequence shown, to 88-106 inch lbs. (10-12 Nm)

    0996b43f8023192e.jpg Fig. Lower oil pan bolt tightening sequence-2.0L engine
    Front exhaust pipe Engine undercover Oil drain plug with a new gasket and tighten to 29 ft. lbs. (40 Nm)

    0996b43f8023192f.jpg Fig. Make sure to the install the new drain plug gasket as shown, or leaks will occur

  5. Lower the vehicle and fill the crankcase to the proper level with clean engine oil.
  6. Connect the negative battery cable. Start the engine and check for leaks.
Non-Turbo Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the engine oil into a suitable container.
  4. Once the oil has completely drained, install the plug and tighten to 25 ft. lbs. (34 Nm).
  5. Remove the front exhaust pipe.
  6. Remove the engine oil dipstick and tube assembly.
  7. Remove the front plate.
  8. Unfasten the oil pan mounting bolts, then remove the oil pan and gasket.

    0996b43f80222121.jpg Fig. Exploded view of the oil pan and related components-1999 2.0L non-turbo engine

To install:
  1. Apply sealant at the point where the engine block meets the oil pump.
  2. Use a new gasket and install the oil pan. Tighten the mounting bolts to 8.9 ft. lbs. (12 Nm).
  3. Install the front plate.
  4. Install the front exhaust pipe.
  5. Install the dipstick and tube assembly.
  6. Safely lower the vehicle to the floor.
  7. Refill the crankcase with oil to the proper level.
  8. nnect the negative battery cable.
  9. Start the engine and check for leaks.

Turbo Engine
  1. Disconnect the negative battery cable.
  2. Safely raise and support the vehicle.
  3. Remove the front exhaust pipe.
  4. Remove the exhaust pipe and muffler assembly.
  5. Drain the engine oil into a suitable container. Once the oil has drained completely, tighten the plug to 29 ft. lbs. (39 Nm).
  6. Remove the dipstick and tube.
  7. For AWD vehicles, remove the transfer case assembly as follows:
    1. With the propeller shaft still installed, remove the transfer mounting bolt.
    2. Insert a suitable prytool in between the transfer case and transaxle, then remove the transfer case from the center shaft.
    3. Remove the transfer case from the center shaft. Do NOT tilt the transfer assembly to the rear or oil will leak out.
    4. After removing the transfer assembly, insert tool MB991193 or equivalent, to prevent the oil from leaking out. Use a piece of wire to suspend the transfer case from the body.

      0996b43f80222122.jpg
      Fig. View of the transfer case with the tool installed to prevent oil from leaking out-1999 2.0L turbo engines
  8. Remove the bell housing cover.
  9. Disconnect the oil return pipe from the oil pan.
  10. Remove the oil pan mounting bolts. Tap the oil pan seal breaker MB998727 or equivalent between the oil pan and the engine block to break the seal and remove the oil pan.

    0996b43f80222123.jpg Fig. Exploded view of the oil pan and sealant application-1999 2.0L Turbo engine

To install:
  1. Clean the sealing surface on the oil pan and engine block. Apply a continuous bead of sealant MD970389 or equivalent to the oil pan.
  2. Clean the oil pan mounting bolt holes in the oil seal case.
  3. Install the oil pan to the engine block. Tighten the mounting bolts to 5.1 ft. lbs. (6.9 Nm).
  4. Use a new gasket and connect the oil return pipe to the oil pan.
  5. Install the bell housing cover.
  6. If equipped with AWD, install the transfer case assembly.
  7. Install the dipstick and tube assembly.
  8. Install the front exhaust pipe.
  9. Install the exhaust pipe and muffler.
  10. Install a new oil filter.
  11. Safely lower the vehicle to the floor and add five quarts of oil to the crankcase.
  12. Connect the negative battery cable.
  13. Start the engine and check for leaks.

Good luck (remember rated this help).

Mar 06, 2010 | 1999 Mitsubishi Eclipse

1 Answer

Oil pan leak


buy a tube of sealer called Right Stuff
1. Remove the flexible exhaust pipe
2. Disconnect the downstream catalyst monitor sendor (OXYGEN SENSOR)
3. Drain engine oil
4. Remove the 15 bolts and the oil pan
5. Clean pan & surface area.
6. Apply sealer 10mm (0.40 inch) diameter of sealer
7. Position oil pan and hand-tighten the oil pan bolts
8. Start with front of oil pan tighten each bolts going around oil pan till all are tighten up.
9. Install exhaust flexible exhaust pipe
10. Connect OXYGEN SENSOR connector
11. Lower the vehicle.
12. Fill oil 5w20 (Spec)

Feb 10, 2010 | 2001 Ford Escape

2 Answers

How can i remove the oil pan gasket?


REMOVAL & INSTALLATION

The radio may contain a coded theft protection circuit. Always obtain the code number before disconnecting the battery.
2.2L, 2.3L and 2.7L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the engine oil into a sealable container.
  4. Install the drain bolt with a new gasket. Tighten the bolt to 33 ft. lbs. (44 Nm).
  5. Remove the front wheels and the splash shield.
  6. Remove the center beam.
5dbe5cd.jpg

Fig. To gain access to the oil pan, remove the center beam-2.2L and 2.3L engines
  1. Detach the Oxygen sensor (O 2 S) electrical connector.
  2. Remove the bolts from the support bracket on the exhaust pipe.
  3. Remove the nuts attaching the exhaust pipe to the exhaust manifold and the catalytic converter.
  4. Remove the exhaust pipe and discard the gaskets.
  5. If equipped with an automatic transaxle, remove the converter cover.
  6. If equipped with a manual transaxle, remove the clutch cover.
  7. Remove the oil pan nuts and bolts (in a criss-cross pattern) and the oil pan; if necessary, use a mallet to tap the corners of the oil pan. DO NOT pry on the pan to get it loose.
  8. Clean the oil pan mounting surface of old gasket material and engine oil.
To install:
  1. Install a new oil pan gasket to the oil pan. Apply liquid gasket to the corners of the curved section of the gasket.
  2. Install the oil pan to the engine.
  3. Install the oil pan nuts and bolts and tighten the nuts and bolts in sequence. Tighten the nuts and bolts in 2 steps to 10 ft. lbs. (14 Nm).
  4. If equipped with an automatic transaxle, install the torque converter cover. Tighten the bolts to 108 inch lbs. (12 Nm).
  5. If equipped with a manual transaxle, install the clutch cover. Tighten the bolts to 108 inch lbs. (12 Nm).
  6. Install the exhaust pipe with new gaskets and new locknuts. Tighten the nuts attaching the exhaust pipe to the manifold to 40 ft. lbs. (54 Nm)and tighten the nuts attaching the exhaust pipe to the catalytic converter to 25 ft. lbs. (33 Nm). Install the bolts to the exhaust pipe support bracket and tighten the bolts to 13 ft. lbs. (18 Nm).
  7. Attach the Oxygen sensor (O 2 S) electrical connector.
  8. Install the center beam and tighten the mounting bolts as follows:

    Prelude: 43 ft. lbs. (60 Nm) Accord: 37 ft. lbs. (50 Nm)
  9. Install the splash shield and tighten the mounting bolts to 84 inch lbs. (10 Nm).
  10. Install the front wheels.
  11. Lower the vehicle and fill the engine with oil.
  12. Connect the negative battery cable and enter the radio security code.
  13. Start the engine and check for leaks.

039a698.jpg

Fig. Oil pan mounting bolt tightening sequence-2.2L and 2.3L engines

402f99d.jpg

Fig. Oil pan tightening sequence-2.7L engines


3.0L Engine

fc8e34b.jpg

Fig. Tighten the oil pan bolts in three steps, in sequence, to 8.7 ft. lbs. (12 Nm)

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the engine undercover.
  4. Drain the engine oil and replace the drain plug.
  5. Remove the front exhaust pipe.
  6. Remove the oil pan mounting bolts.
  7. Hammer a seal cutter between the engine block and oil pan to break the seal.
  8. Remove the oil pan.
To install:
  1. Clean the oil pan flange and engine block mounting surface.
  2. Apply sealant to the oil pan flange. Be sure to apply sealant toward the inside of the bolt holes.
  3. Install the oil pan on the engine. Tighten the bolts in sequence to 8.7 ft. lbs. (12 Nm).
  4. Install the exhaust pipe.
  5. Install the undercover.
  6. Lower the vehicle.
WARNING Operating the engine without the proper amount and type of engine oil will result in severe engine damage.
  1. Refill the engine with the correct amount of oil.
  2. Connect the negative battery cable.
  3. Start the engine and check for leaks.

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 1996 Honda Accord

1 Answer

How do I replace the oil pan gasket on a 2001 GMC Yukon XL?


Changing the oil pan gasket on a GMC Yukon XL is realtively simple, but does require removal of the exhaust pipe. You will need a new oil pan gasket and a new exhaust pipe flange gasket.
Put the car on ramps or jacks to access the undercarriage.
Remove the exhaust pipe by removing the 3 nuts holding the exhaust pipe flange to the exhaust manifold. These nuts often rust and prior application of penetrating oil may be required to remove them without damage. Once the pipe is unbolted, work the exhaust system loose from the hanging brackets. In most cases the entire system does not have to be removed since there is enough room to remove the pan with only the front hangers removed.
Drain the oil from the engine
Remove the 10 mm bolts holding the pan to the block.
Remove the old gasket material and scrape any remaining gasket from the block and pan.
Install the new gasket. Forma-Gasket or a similar product may be used in small quantities to "glue" the new gasket in place and prevent shifting while the pan is reattached to the block.
Reinsall the 10 mm bolts in a cross pattern to ensure the gasket is compressed evenly. Do not overtighten the bolts.
Replace the pipe to flange gasket between the exhaust pipe and the exhaust manifold with a new part.
Reattach the exhuast pipe to the hangers.
Install the 3 bolts connecting the pipe flange to the exhaust manifold.
Fill the engine with oil.

Sep 15, 2009 | 2001 GMC Yukon

1 Answer

2003 oil pan removal


4.0L Engine To Remove:
  1. Disconnect negative battery cable.
  2. Lift the vehicle.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Exhaust pipe from exhaust manifold.
    • Exhaust hanger at the catalytic converter and lower the pipe.
    • Starter motor.
    • Flywheel/torque converter housing access cover.
    • Oil level sensor (if equipped).
  5. Place a pole jack under vibration dampener with a piece of wood between dampener and jack.
  6. Remove or disconnect the following:
    • Engine mount through bolts and raise engine for clearance to remove pan.
    • Transmission cooler lines (if equipped).
    • Oxygen sensor harness from oil pan mounting studs.
    • Oil pan bolts and studs.
    • Oil pan and gasket.
To Install:
  1. Clean the gasket mating surfaces.
  2. Apply Mopar® Silicone Adhesive Sealant or equivalent onto the cylinder block in four location as shown.
7605306.gif

  1. Attach the pan gasket to the oil pan with Hi-tack or equivalent (2003-2005 vheicles).
  2. Use 1 ½ x ¼ inch bolts to fabricate alignment dowels. Cut off the head of the bolts and cut a slot into the top of the dowels (2006 vehicles).
4e495fd.gif

  1. Install two dowels into the timing case cover (2006 vehicles).
  2. Install two dowels into the cylinder block (2006 vehicles).
  3. Place the gasket over the dowels and onto the cylinder block and timing case cover (2006 vehicles).
  4. Position the oil pan.
  5. Install the 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm).
  6. Install the 5/16 inch oil pan bolts. Tighten to 132 in-lb (15 Nm).
  7. Remove the dowels.
  8. Install the remaining 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm) (2006 vehicles).
  9. Lower the engine onto the engine mounts.
  10. Install the through bolts and tighten the nuts.
  11. Remove jack stand and remove the piece of wood.
  12. Install the flywheel and torque converter access cover.
  13. Install starter motor.
  14. Connect the exhaust pipe to the hanger and to exhaust manifold.
  15. Install the transmission oil cooling lines (if equipped).
  16. Install the oxygen sensor wiring supports to the oil pan mounting studs.
  17. Install the drain plug into the oil pan. Tighten to 25 ft-lb (34 Nm).
  18. Lower the vehicle.
  19. Connect negative battery cable.
  20. Fill the oil pan with oil. WARNING
    Use extreme caution when the engine is operating. Do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
  21. Start the engine and inspect for leaks.

Jun 06, 2009 | 2003 Jeep Wrangler

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
1995 Honda Civic Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...