Question about 1993 Chevrolet S-10 Blazer

1 Answer

Car starter cant get starter in keeps hitting by gear hard to get out also but did by prying out

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 241 Answers

Come again ..

Posted on May 15, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How can I reach starter to tap on it in 1997 Pontiac bonneville?

Starter is on the front side of the engine. Long rod/pry bar will get to it. Other wise get under it. Drivers side at where the engine and transmission comes together. Don't tap, hit it hard.

Dec 26, 2016 | Pontiac Cars & Trucks

2 Answers

Changed starter but when engaged gear grinding and hits hard gears are OK on both starter and ring gear 1998 Dakota v6 3.9l any suggestions as to what to do. Bolts are tight

To me it sounds like the started is not lined up properly, because if it was lined up right, it wouldn't be doing what it is. Believe me, i have changed a lot of starters in my lifetime.

Jul 02, 2015 | Cars & Trucks

3 Answers

Wont turn on ?

more info about your car and problem will help to answer to your question

Apr 22, 2015 | Cars & Trucks

2 Answers


Hit it with a hammer, the starter that is ...not too hard - just trying to make it turn a little because sometimes there's just a missing gear tooth .....

Oct 17, 2013 | 2001 Cadillac DeVille

1 Answer

2005 pontiac montana won't start

Try tapping on the side of the starter with a pry bar and a hammer. Do not hit too hard though. Hitting too hard will damage the starter. If the engine starts try cleaning the electrical contacts on the starter. If the problem persists replace the starter.

Apr 03, 2012 | 2005 Pontiac Montana

1 Answer

How do i replace cv joint on a ford taurus 2003 i cant get the control arm off please help

The control arm is attached with the ball joint,remove the nut on the ball joint,and hit around the stud of the ball joint,hit it hard,but do not hit the stud of the ball joint,it will jar it loose,then use a large pry bar,and stick in the control arm and pry downwards,It is not easy to get the ball joint stud out of the spindle,but it is the only way.but make sure the stud of the ball joint is free from the control arm then push down on the control arm(pry)

Apr 24, 2010 | 2003 Ford Taurus

1 Answer

My jeep won't start. It has power. Recently replaced the battery and connections. It is making a clicking noise when I turn the key.

Hi, the clicking noise you hear is the selenoid in the starter motor not engaging the drive to start the engine all you need to do is replace you starter motor and then you should find you will have no problems starting your car.

Another trick you could try just to get it started is give the starter motor a few hits with a hammer hit it quite hard but not hard enough to break it doing this will usually get it started but dont rely on this being a permanent fix as it could leave you stranded.

Also if you have a manual gear box you could get someone to help you push the car whilst its in gear with the clutch to the floor 2nd gear is best for this then once the car is rolling let the clutch up whilst the ignition is on this should then fire up the engine if it dont try the key as this will sometimes get the starter working again for a short while.

Let me know how you get on or if you need further assistance ok

Feb 28, 2010 | 1997 Jeep Grand Cherokee

1 Answer

1987 jeep yj 6 cyl manual trans. New fly wheel, clutch, presure plate, and batt. Starter is one month old on old worn flywheel with bad ring gear. Inspected starter gear before reinstalled on the new fly...

check to make sure the starter is seated correctly to the bell housing also check for a cracked! nose cone on the starter as well and make sure the front nose casting bushing isn;t worn out and make sure they sold you the correct tooth count flywheel

Jan 19, 2010 | 1987 Jeep Wrangler

2 Answers

I just bought a 92 jeep cherokee ran beautiful . now it just sits there cant get it to start . battery was dead replaced still wont start . cant tell if its the ignition or the starter.

I'm assuming the starter is not turning the engine...check the small wire on the starter for 12v with key turned to start. If no voltage there, check ignition switch and neutral start switch. (voltage in, voltage out)

May 09, 2009 | 1992 Jeep Cherokee Sport

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides