Question about 1998 Mercury Mountaineer

Open Question

Mercury mountaineer 98 driver seat removal - 1998 Mercury Mountaineer

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: seat heater won't turn off

Is there a fuse under there
or see if you can unplug it and plug it back in
see if that works

Posted on Feb 06, 2009

Ad
michigan man
  • 3533 Answers

SOURCE: 1998 Mercury Mountaineer Plastic Fan

yes this sounds correct but if you want to get a diagram and step by step instructions try "autozone.com"

Posted on Mar 08, 2009

  • 72 Answers

SOURCE: I could not find the speed sensor location on my

The Output Shaft Speed Sensor is located at the lefthand, (sitting in the driver's seat) rear of the transmission.

Posted on Jul 18, 2009

fingaz22
  • 1068 Answers

SOURCE: my hood wont close on a 98 mercury mountaineer

if it doesn't lock then i would look at the latch assembly and spray it with wd-40 they get stuck because of rust and corrosion. also take a look at the handle inside the vehicle they also get stuck in the pulled out position and causing the hood to not lock. give it a push to insure it is in the full depressed position. good luck

Posted on Sep 22, 2009

  • 176 Answers

SOURCE: where is the PCV valve on a mercury mountaineer 98

on the 5.0 liter it is in the rear lower intake manifold

Posted on Feb 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mountaineer power seat


Seat motor needs to be replaced.

Mar 02, 2014 | Cars & Trucks

1 Answer

Seat heater control switch 2004 Mercuty Mountaineer


remove the bolts holding on your seat. if it has seat bags fitted do not do that as you have a procedure for doing that.

Dec 21, 2013 | 2004 Mercury Mountaineer

1 Answer

I have no power on my 98 mercury mountaineer battery is good what can i check first


If the battery is a top post, remove the cables and clean. Make them shinney and then replace.

Mar 14, 2013 | 1998 Mercury Mountaineer

1 Answer

How do I replace the rear wheel studs on a 2006 Mercury Mountainer?


Take the wheel off,remove brake drum,hammer stud through axle hub,pull new stud through hub with lug nut until seated against axle hub.

Sep 03, 2012 | 2006 Mercury Mountaineer

1 Answer

2007 mountaineer drivers seat will not recline


Hi Lee, It could be a switch problem or the motor. Each function has a different motor. Regards John

Jul 02, 2012 | 2007 Mercury Mountaineer

2 Answers

2004 mercury mountaineer driver side heated seat not working but the light comes on


It is very common for seat heaters to fail. You can disconnect the heater from the wiring and place a voltmeter on the wiring. If you get a reading, then seat heater is bad.

Dec 31, 2010 | 2004 Mercury Mountaineer

1 Answer

Just bought a 2002 Mountaineer w/keyless entry. The problem is no one at the dealer knows the code. How can I reset it?


In the 2002 Mercury Mountaineer, especially with the 3rd row seat, remove the trim panels at the rear of the back door and at the tailgate on the passenger side. You will see two panels where the wall seat belt is located, remove the top panel first and then pull the lower panel out.Then pull the lower trim panel forward CAREFULLY. Towards the front (near the door opening) you will see a small black box (says Security Unit) On it in fairly small print will be the 5 digit code.
[ONE set of FIVE numbers and that is your CODE number.]

Nov 16, 2010 | 2002 Mercury Mountaineer

1 Answer

I could not find the speed sensor location on my 98 mercury mountaineer. Where is it?


The Output Shaft Speed Sensor is located at the lefthand, (sitting in the driver's seat) rear of the transmission.

Jul 18, 2009 | 1998 Mercury Mountaineer

Not finding what you are looking for?
1998 Mercury Mountaineer Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...