Question about 2002 Jeep Liberty

Open Question

What do the code p0320 and p0700 mean - 2002 Jeep Liberty

Posted by on

  • yadayada
    yadayada Sep 12, 2010

    You have a transmission failure

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 jeep liberty p0320 and p0700. Any idea what this means?


p320..its the crankshaft position sensor.
The p0700..Transmission Control System Malfunction
P0700 means that a code has been set in the Transmission/Transaxle Controller.
This code is for information ONLY.
If P0700 is present, check for Transmission/Transaxle codes. need a scan tool. One weird thing that has been known to throw this one is a weak battery, ck that too. Changing the Crank position sensor may very well clear it. Start there.
to clear all codes disconnect the battery for 10 minutes.
hope this helps you.
good luck.

Jan 10, 2018 | Jeep Cars & Trucks

1 Answer

2000 ford f150 Manuel trans. Code p0320 is it a expensive repair? Stutters while in gear 3/4 but doesn't stall. Just started a few days ago


P0320 means that an ignition pulse that's supposed to fire a spark plug was missed. It could be as simple as a chafed wire under the hood. Watch this video:


Ford has some information too:
P0320 2000 Ford F150 Ignition Distributor Engine Speed Input Circuit...

Oct 02, 2015 | Ford Cars & Trucks

1 Answer

What dose the code p0320 mean on a 2001 town&country chrysler caravan


code p0320 means faults crankshaft position sensor (CKP) sensor/ engine speed (RPM) sensor ---circuit malfunction. Check Wiring---CKP/RPM and ECM engine control module

Mar 08, 2013 | Cars & Trucks

2 Answers

What do the codes P1684 and P0700 mean?


Hi Rich Stuck,P0700 means Transmission Control System (MIL Request),P1684 means Battery Disconnected within last 50 starts.More read Diagnostic Trouble Code Table ,hope it can help you.

Dec 08, 2012 | 2002 Chrysler PT Cruiser

1 Answer

2006 dodge 1500 hemi-trouble codes p0700 and p0800, what are they?


the P0700 means Transmission Control System (MIL Request)
the P0800 means Transfer Case Control Circuit

hid conversion kits

Aug 27, 2012 | 2006 Dodge Ram

3 Answers

Car does not run ,I check the code ,it is P0700


Because it is not starting, you should replace the Crankshaft sensor (above the oil filter, back of the engine)-it will cause a P0700-I have a 99 SL2, 178,000 miles


DTC) CODE # P0700....Transmission Control System (MIL Request)
Translation: Transmission Control Module (TCM) Malfunction or Failure. P0700 Information Code The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM. This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it. The dealer probably saw the code P0700 and went to the TCM and pulled out the code stored there telling them the Transmission Solenoid Assembly (TSA) is bad. This is a good example of understanding what the codes actually mean. If the manual you looked at said the TCM is bad and to replace the TCM when you see a P0700, then it is wrong.

Jan 24, 2011 | Saturn Ion Cars & Trucks

1 Answer

Car stopped running while driving diagnostic codes read p0320 and p0171 what is the remedy?


Trouble code P0320 means: Ignition Engine Speed Input Circuit Malfunction

Crankshaft Speed sensor should be replaced.

p0171 is a lean condition for the right passenger side of the vehicle bank 1 on vehicles with rear wheel drive v6 or v8.

Sep 06, 2010 | Ford Focus Cars & Trucks

1 Answer

I have code P0320 and P0340 on my jeep liberty what does this mean


P0320 Ignition Engine Speed Input Circuit malfunction

P0340 Camshaft Position Sensor Circuit malfunction

Apr 15, 2010 | 2003 Jeep Liberty

1 Answer

P0700 and p0320 truck runs for approx 10min stalls tach jumps all over the place and injectors fire and fill culinders with fuel to the point of hydraulic lock


P0700------ problem in the transmission control system
P0320------ problem in the ignition/distributor. If equipped with a distributor, change the cap and rotor, probably a good idea to do a tune up, change spark plugs and wires.

Nov 20, 2009 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...