Question about Jeep Liberty

1 Answer

Air work on all 4 levels. then 1 stopped, a mth later 2 stopped and so forth. level 4 was the only one that remained working for about 7 mths. it now doesn't work unless the jeep is in motion

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 672 Answers

Replace blower motor resistor!!

Posted on Sep 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you drive the vehicle when the rear suspension leveler is not working.


Lincoln Town Car Questions - Rear suspension - CarGurus

www.cargurus.com > Questions > Lincoln > Town Car

CarGurusFeb 7, 2015 - Rear suspension - Should the rear airbags deflate after I turn off ...seems to be no leaks cause the pump turns off and I don't hear it going off and on whiledriving. ... dead so you have leak when you jacked up car if not turn off air you could... car pumps up and bleeds off later the problem is NOT the leveler.

2002 Lincoln TC Air suspension not working - CarGurus

www.cargurus.com > Questions > Lincoln > Town Car

CarGurusJul 23, 2012 - 2002 Lincoln TC Air suspension not working - My 2002 TC airsuspension ... 2012 at 09:25 PM about the 2002 Lincoln Town Car Executive ... I did not pay attention that you said the compressor is OK. ... Rear Air Suspension 2 answers ... How can I test my Air suspension height leveling sensor on my 1997 ...

Dec 25, 2015 | Cars & Trucks

Tip

Mack Fault Codes List


FAULT CODE IDENTIFICATION TABLE - VMACIII - 1998 & NEWER
1-1 Engine Oil Pressure Sensor
1-2 Barometric Pressure Sensor
1-3 Fuel Temperature Sensor
1-4 Ambient Air Temp Sensor
1-6 Starter Input
1-7 Engine Coolant Level
1-8 (ASET CEGR) Estimated % Fan Speed
1-10 Aux. Cooling Relay Output
2-1 Engine Coolant Temp Sensor
2-2 (ASET IEGR) Boost Air Pressure Sensor
2-2 (ASET CEGR) Boost Air Pressure
2-3 Intake Air Temp Sensor
2-4 Trans Oil Temp Sensor
2-5 Front Drive Axle Oil Temp Sensor
2-6 Rear Drive Axle Oil Temp Sensor
2-7 Engine Oil Temp Sensor
2-8 (ASET CEGR) Combustion Air Temperature
2-9 (ASET CEGR) Combustion Air Temp Sensor
3-1 Exhaust Temperature Sensor
3-2 Engine Speed Sensor
3-3 Redundant Engine Speed
3-4 Engine Position Sensor
3-5 Engine Brake Output #1
3-6 Engine Brake Output #2
3-8 Trans Splitter Position
3-10 (ASET CEGR) Engine Brake Output #3
4-1 Vehicle Speed Sensor (VSS)
4-2 Fan Clutch Output
4-3 Auxiliary Output #1
4-4 Auxiliary Output #2
4-5 (ASET IEGR) Wastegate Output
4-5 (ASET CEGR) VTG Position Sensor
4-6 Tachometer Output
4-7 Speedometer Output
4-8 Customer Defined Statement
4-9 (ASET CEGR) EGR Valve Mechanism
5-1 Throttle Position Sensor
5-2 Throttle Position Sensor Reference Voltage
5-3 Engine Shutdown Lamp/Alarm
5-5 Electronic Malfunction Lamp
5-6 Spare Relay #3
5-7 Engine Oil Level
5-8 (ASET CEGR) EGR Temperature
5-9 (ASET CEGR) EGR Mass Flow
6-1 Fuel Level
6-2 (ASET CEGR) Turbocharger Speed
6-3 J1708/J1587 Link
6-4 J1939 Link
6-5 All Communication Lost - Engine Shutdown
6-6 Fuel Control Module
6-7 Power Relay
6-8 J1939 Link
6-9 Other ECU Affecting Operation
7-1 Service Brake Switch
7-2 Parking Brake Switch
7-3 Speed Control SET Switch
7-4 Speed Control RESUME Switch
7-5 Battery / Alternator Voltage
7-6 Switched Voltage
7-7 Exhaust Temp Reference
7-9 VTG Actuator
8-1 Electronic Unit Pump #1
8-2 Electronic Unit Pump #2
8-3 Electronic Unit Pump #3
8-4 Electronic Unit Pump #4
8-5 Electronic Unit Pump #5
8-6 Electronic Unit Pump #6
8-9 Solenoid Boost Voltage
9-1 Transport Protocol
9-2 Power Reset Without Key Switch
9-3 (ASET CEGR) Aftercooler Outlet Temperature
9-5 (ASET CEGR) Compressor Discharge Temp
9-8 (ASET CEGR) Auxiliary Output Device #1
9-9 (ASET CEGR) Auxiliary Output Device #2
9-10 (ASET CEGR) Auxiliary Output Device #3
10-1 (ASET CEGR) Internal Sensor Voltage
10-2 (ASET CEGR) 5 Bolt Supply
10-3 (ASET CEGR) Sensor Supply Voltage #1
10-4 (ASET CEGR) Sensor Supply Voltage #2
10-5 (ASET CEGR) Fuel Filter Differential Pressure
10-6 (ASET CEGR) Fuel Delivery Pressure
10-7 (ASET CEGR) Odometer Save Area Failure
10-8 (ASET CEGR) GPS Position Data Not Received
10-9 (ASET CEGR) Watchdog Timer Reset


source

on Dec 20, 2016 | Cars & Trucks

1 Answer

Need info on how to change a 2000 Cadillac


REMOVAL PROCEDURE
TOOLS REQUIRED
A J 34730-1A Fuel Pressure Gauge
A J 39765 Fuel Sender Lock Nut Wrench
CAUTION: Refer to Batterry- Disconnect Caution in Service Precautions.
1. Disconnect the negative battery cable.
2. Relieve the fuel system pressure. Refer to the Fuel Pressure Relief Procedure. See:
Fuel Delivery and Air Induction/Fuel Filter/Fuel Pressure Release/Service and
Repair
3. Drain the fuel tank. Refer to Fuel Tank Draining Procedure. See: Fuel Delivery and
Air Induction/Fuel Tank/Service and Repair/Procedures
4. Remove the fuel tank.
5. Remove the fuel sender assembly.
6. Disconnect the fuel pump electrical connector (5).
7. Remove the fuel level sensor electrical connector retaining clip (6).
8. Disconnect the fuel level sensor electrical connector (7) from under the fuel sender
cover.
9. Remove the fuel level sensor retaining clip (4).
10. Squeeze the locking fangs and remove the fuel level sensor (3).
INSTALLATION PROCEDURE
1. Install the fuel level sensor (3).
2. Install the fuel level sensor retaining clip (4).
3. Connect the fuel level s ens oi electrical connector (7).
4. Connect the fuel level sensor electrical connector retaining clip (6).
5. Connect the fuel pump electrical connector (5).
6. Install the fuel sender assembly.
7. Install the fuel tank.
8. Refill the fuel tank.
9. Install the fuel filler cap.
10. Connect the negative battery cable.
11. Inspect for leaks.
11.1. Turn ON the ignition for 2 seconds.
11.2. Turn OFF the ignition for 10 seconds.
11.3. Turn ON the ignition.
11.4. Inspect for fuel leaks. 55dcc1df-120b-4a37-b63b-a35953989584.png

Aug 29, 2014 | Cars & Trucks

1 Answer

How to bleed clutch 2007 compass


GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

2. Raise vehicle on hoist.

3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

8. From driver's seat, actuate clutch pedal 60-100 times.

9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

6. Turn on the service filling machine.

7. Crack open the bleeder valve (3).

8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

10. Close the bleeder valve and disconnect the service filling machine.

11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

12. Check clutch pedal to see if vehicle is properly bled.

13. If vehicle is not properly bled, repeat procedure.

14. Remove bleeder cap from reservoir and replace reservoir cap.

15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

Oct 15, 2013 | 2007 Jeep Compass Limited

1 Answer

I just filled up my tank and now the light is on and the tank shows empty?


{: ) Your fuel level sensor could be intermittently reading high resistance and may need replacement. An intermittent reading can happen at any level (say 1/4, 1/2, 3/4) and will suddenly give you an empty reading and fuel light, sometimes an SES light may follow. At any rate, this kind of symptoms still recommends replacement of the fuel level sensor.
You can observe it by yourself. Does it read normal on lets say half full but will read empty when you can calculate that you still have 1/4 remaining on your tank. In your case you've just filled it full, and it's no different once the fuel level sensor start getting erratic readings.
Although it may take time, you can wait until the fuel level stabilizes to a certain lower level where you think your gauge was reading normally before. You can also do some stop and go, forward and reverse, to slosh the level arm to a a more readable position. Check if you can get clearer results out of this trick.
A scan tool is a better tool to determine quickly the condition of the sensor and may tell also if there are other codes that is related to your problem.

Jul 16, 2011 | 2006 Chevrolet Trailblazer

1 Answer

My xterra's air conditioning will not work. The a/c compressor won't engage on blower levels 2, 3 and 4. The a/c compressor will engage on level 1. The blower only works on levels 2, 3 and 4. The...


Typically when the blower only works on high it is because the blower motor resistor is faulty. The first thing I would do is have it checked or replaced and see if your lights are still not working right.

There are not too many other things that this could be, but it might be a wiring problem or a problem with the A/C controls or control module.

I hope this has helped.

May 05, 2010 | Nissan Xterra Cars & Trucks

1 Answer

Fan won't blow on levels 1, 2, and 3 but will on 4 and 5


you need a blower motor relay under the pass side of dash

Mar 09, 2009 | 2002 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...