Question about 1990 GMC C1500

1 Answer

90 chev truck

Adjusting doors

Posted by on

  • jed69 May 14, 2008

    adjusting doors

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 175 Answers

There is no door adjustment usually needed. On these trucks the hinge pin bushings wear out. open your door slightly, then try picking up on it by grabbing the end of the door and pulling up. if you are able to move it up and down, you need new hing pins and bushings. they are about 8 bucks each (2 per door) and are found at your parts store in the Help! section of hardware. good Luck.

Posted on May 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 chev blazer is it possible to adjust or by pass the heat actuator to get it to defrost mode


Consider just taking both heater hoses in the engine compartment and loop them together. This will bypass the heater coil and keep the heat out of the passengers zone.

You may find more relevant info at this link:

Fix Heat Door Actuator

Feb 12, 2015 | Cars & Trucks

1 Answer

Door adjust for 71 Chev C20


  • Open the door and locate the two hinges where the door pivots from the vehicle.
  • 2Look for any wear or bending on either hinge. The hinge that looks bent or otherwise damaged will be the one you want to adjust.
  • 3
    Loosen the bolts with the socket wrench on the affected hinge just enough to where it could be moved with the pry bar.
  • 4Move the hinge forward or backward in small increments, then gently try to close the door to see if it is back in alignment. If it isn't, continue to move it either frontward or backward until the door closes securely and without slamming.
  • 5
    Tighten all parts
  • Sep 04, 2012 | Chevrolet Chevrolet Cars & Trucks

    1 Answer

    Torque and tightening sequence for 1999 2.2 chev


    Cylinder Head Bolts

    Step 1
    Head Bolts A 46 (62)
    Head Bolts B 43 (58)

    Step 2 Additional 90 Degrees

    Tightening Sequence:
    http://www.anubiscycle.com/fixya/99cavheadsquence.png

    Jan 17, 2010 | 1998 Chevrolet Cavalier

    1 Answer

    How can i align the headlamps for a 2003 chev. impala


    Pull up to within 20 feet of a wall or garage door and adjust them using a "star" screwdriver. The adjustment screws should be located just above the headlight assembly. Simply watch the beams as you turn the screws either clockwise or counter clockwise. At 20 feet the beams should be roughly 3 feet off the ground. Hope this helps.

    Dec 11, 2009 | 2003 Chevrolet Impala

    2 Answers

    HAVING TO PUSH THE STICK SHIFT UPWARD 1981 chev c10 truck


    if it is an automatic a lot of newer cars are made that way its a saftey feature

    Jun 03, 2009 | 1995 Nissan Pickup

    1 Answer

    02 chev venture power sliding door


    the plungers seem to be an issue not making good contact twist them around in their bore and also try to initialize the door

    Feb 03, 2009 | 2001 Chevrolet Venture

    1 Answer

    Tightening head


    New Headbolts are recommended

    Long bolts are torqued to 46'lbs + 90 degrees.

    Short bolts are torqued 43'lbs + 90 degrees.

    Start in the center, and work to the edges, torquing the bolts in two stages.

    Rockers are torqued to 22'lbs.

    Dec 21, 2008 | 1999 Chevrolet Cavalier

    1 Answer

    Chev avalanche 2004 inner tie rods


    I was able to fix the inner tie rod problem with a little of patients and 90 bucks for the parts. When I took it in for the front end to be aligned the drivers side was only off by 1/4 on an inch.

    Nov 07, 2008 | 2004 Chevrolet Avalanche

    2 Answers

    Can't get low gear


    if memmory serves me correct its been a while since last tranny rebuild and adjustment
    on a 700-r4 type transmission
    make sure that the shim kit was used properly with this transmission cause wrong sized length of linkage can make the trans. shift improperly
    you have the linkage under neith adjusted wrong the shift bar on tranny should face 90 degrees up towards front of vehicle engine for proper adjustment

    Jun 06, 2008 | Chevrolet Nova Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    155 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    71288 Answers

    Freddy

    Level 3 Expert

    1311 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22059 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...