Question about 2005 Chrysler PT Cruiser

1 Answer

Crankshaft position sensor replacement 2005 pt cruiser

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

It helps if you can lift or jack up the vehicle. be sure & use jack stands. it should be above oil filter on engine block under exhaust manifold. look for a sensor with one bolt holding it on. also check for frayed wires rubbing on cv shaft. sometimes all they need is fix one frayed wire

Posted on Sep 15, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: Crankshaft Position Sensor location 04 PT Cruiser

It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Posted on Feb 08, 2009

  • 412 Answers

SOURCE: where can I find the crankshaft position sensor on

IT IS LOCATED IN THE BLOCK BELOW THE STARTER..UNPLUG CONNECTOR AND 1 BOLT..IT MAY BE STUCK IN BLOCK..SPRAY WITH PENETRATING OIL..MOVE BACK AND FORTH PULL OUT OF BLOCK

Posted on Jul 14, 2009

  • 1 Answer

SOURCE: location of crankshaft position sensor for 2003

Had this problem. The crankshaft position sensor (on 2003 non-turbo) is located directly under the starter. The Haynes and Chilton books will tell you the complete opposite. They state that it is located near the alternator. WRONG. Oh, it is really a pain to get to FYI.

Posted on May 25, 2010

  • 27 Answers

SOURCE: were i the crankshaft position

near the oil filter.. above it...under exhaust manifold one small bolt holds it on. If the is a no start condition look for frayed wiring near crank sensor..... it has a harness that hangs too low on some of those. & rubs on cv shaft

Posted on Sep 15, 2010

  • 3 Answers

SOURCE: location crankshaft position sensor 2004

Its located on the engine block usually the front

Posted on Mar 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change cam and crankshaft sensor for pt cruiser 2005 and still in the diagnostic problem cam sensor


just remove the battery terminals for a while firstly removing negative terminal

Sep 17, 2013 | 2005 Chrysler PT Cruiser

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

2 Answers

Where is crank sensor on 2005 PT Cruiser? It absolutely is not above the oil filter as on 01-03 PT's.


REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Aug 22, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Were i the crankshaft position sensor located o a 2005 pt cruiser


near the oil filter.. above it...under exhaust manifold one small bolt holds it on. If the is a no start condition look for frayed wiring near crank sensor..... it has a harness that hangs too low on some of those. & rubs on cv shaft

Sep 14, 2010 | 2005 Chrysler PT Cruiser

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...


P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Where can I find the crankshaft position sensor on a 2005 Pt Cruiser Non turbo gasoline


IT IS LOCATED IN THE BLOCK BELOW THE STARTER..UNPLUG CONNECTOR AND 1 BOLT..IT MAY BE STUCK IN BLOCK..SPRAY WITH PENETRATING OIL..MOVE BACK AND FORTH PULL OUT OF BLOCK

Jul 14, 2009 | 2004 Chrysler PT Cruiser

3 Answers

Code PO340


P0340 is a Crankshaft Position Sensor error. It determines firing order and is most likely the cause of your problem. It's mounted near the oil filter on the engine block. Below is a picture of how it appears in your car. Best of luck.
Greg


23ad084.gif

Jul 13, 2009 | 2005 Chrysler PT Cruiser

1 Answer

Error code P0335 (2005 pt cruiser)


p0335 is crankshaft position sensor circuit fault code..possible just a faulty sensor,shouldn't set a circuit code if timing is off..a sensor is probably around a 100 bucks..located just above starter in block

May 18, 2009 | 2005 Chrysler PT Cruiser

1 Answer

Crankshaft Position Sensor location 04 PT Cruiser


It is located behind the **** of the starter on the front of the engine starting in '03 the 2.4 lt was changes the repair manual failed to update this..you may sneak it out with small fingers with out pulling out the starter.

7e1821a.jpg

Feb 08, 2009 | 2004 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

1,498 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...