Question about 2002 Chrysler Voyager

1 Answer

What is the oil pan capacity? - 2002 Chrysler Voyager

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

It requires 5 quarts of oil.

Posted on Sep 21, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is oil capacity?


Oil capacity will be listed in the specifications in the vehicle handbook along with the recommended grades.

There is often two capacities listed; one being the capacity of the oil pan and the other being the capacity of the oil filter.

When refilling the engine it is good practice to slightly underfill so after running and standing the level is between the maximum and minimum marks on the dipstick.

Feb 22, 2016 | Cars & Trucks

1 Answer

What is the capacity(volum)of transmission and engin oil in denali 2007?


{: ) Engine Oil with Filter - All Engines 5.7 L (6.0 qt)
Transmission fluid:
4L60-E/4L65-E/4L70-E Pan Removal (4.7L), 4L80-E/4L85-E Pan Removal (7.3L),
6L50/6L80/6L90 Pan Removal (5.7L)

May 13, 2011 | 2007 GMC Yukon Denali

1 Answer

How to change oil pan?


Step 1: Place car on jack stands or car ramps ( i prefer jack stands because i had a car ramp collapse on me once. not fun) and block the back tires.
Step 2: Loosen and remove the oil pan drain plug and drain oil into a drain pan
Step 3: Look on the outer edges of the oil pan and you will see bolts going all around the outside of the pan. Loosen them and the pan should come off.
Step 4: clean the surface where the gasket comes into contact with the engine, and if you are using the same oil pan peel the old gasket off and clean the surface on the oil pan where the gasket goes.
Step 5: Place the new gasket on the oil pan and stick the oil pan up onto the engine and stick a few bolts in on each side. Make sure the gasket stays aligned with all the bolt holes. You may use some RTV on the gasket but if the surfaces are good and clean you shouldnt have to
Step 6: tighten all the bolts to spec according to the repair manual for your vehicle
Step 7: Fill your engine with the correct type and capacity and then start the engine up and check for leaks
Step 8: Your Done!!

Jan 03, 2011 | 2000 Chevrolet Venture

2 Answers

Where is the oil pan?


on the bottom of the engine it will have a head of a bolt in it that is the drain bolt

Dec 12, 2010 | 2005 Chevrolet Cavalier

1 Answer

Won.t shift into grear, how do i replace the tansmission filter?


TO DO A TRANSMISSION FLUID CHANGE YOU NEED HAVE TRANSMISSION FLUID ON HAND YOU NEED TRANSMISSION FILTER AND GASKET.YOU NEED 3/8 WRENCH THE RATCHET TYPE WITH METRIC SOCKETS. YOU NEED JACK TO RAISE VECHICLE SUPPORT VECHICLE ON JACK STANDS.YOU NEED A DRAIN PAN. ONCE YOU GET VECHICLE OFF GROUND.PLACE DRAIN PAN UNDER TRANSMISSION OIL PAN REMOVE OIL PAN DRAIN BOLT.LET FLUID DRAIN OUT IN DRAIN PAN THEN SCREW DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.REMOVE OIL PAN AND GASKET. BESURE TO HAVE PAPER TOWEL ON HAND.MAKE SURE TRANSMISSION OIL PAN GASKET SURFACE CLEAN BEFORE INSTALLING NEW PAN GASKET. ONCE TRANSMISSION OIL PAN REMOVED. REMOVE THE OLD TRANSMISSION FILTER INSTALL THE NEW FILTER.THEN WITH NEW GASKET ON OIL PAN IN PLACE.OIL PAN NEED TO BE CLEAN SO THE GASKET ADHESIVE WILL HOLD PAN GASKET IN PLACE WHILE INSTALLING PAN AND GASKET TO TRANSMISSION.INSTALL OIL PAN BOLTS INSTALL THEM CRISS CROSS TORQUE PAN BOLTS TO 7 TO 10 FT LBS. LOOK IN OWNERS MANUAL FOR TRANSMISSION FLUID CAPACITY.BUY 10 QUARTS .TO BE ON SAFE SIDE SO YOU WILL HAVE ENOUGH FLUID ON HAND. IF YOU DONT HAVE NO TRANSMISSION FLUID CAPACITY. ADD 7.5 QUARTS FLUID.WAIT FOR 2 MINUTES.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK. SHOULD BE ON THE FULL MARK.CRANK VECHICLE UP.LET IDLE FEW MINUTES CHECK TRANSMISSION DIP FLUID LEVEL IF DROPPED ADD LITTLE MORE.WHILE ENGINE IDLING GETTING WARM UP. KEEP EYE ON FLUID LEVEL.WHEN FLUID LEVEL STOP DROPPING. APPLY BRAKES HOLD FOOT ON BRAKES SHIFT THROUGH ALL GEARS TWO TIMES. THEN CHECK FLUID LEVEL SHOULD BE ON FULL MARK.CHECK FOR LEAKS WHILE ENGINE RUNNING.

Nov 19, 2010 | 1996 Ford F250 Crew Cab

1 Answer

4 cylinder oil capacity


Most 4 cylinder engines have a capacity of between 4 and 5 liters.
I would put 4 liters in , run the engine for a minute or two , wait a couple more minutes for the oil to drain back down into the oil pan , and then check the dipstick. Vehicle should be on reasonably level ground to get and accurate dipstick reading.

Oct 18, 2010 | 2006 Mercury Mariner

1 Answer

What is the oil capacity on a 1989 vw Golf 1.8 sohc?


4.5qt for oil change
5.0qt for dry engine
Unless you have upgraded to a 5qt baffled oil pan then the above is the right measurement.

May 19, 2010 | 1989 Volkswagen Golf

1 Answer

Where is the oil filter?


on most vehicles the oil filter is can shaped and mounted on the engine block, and will be found from under neath of the vehicle to change the oil 1 jack the front of the vehicle and secure it on stands 2 place a collection pan under the vehicle (large enough to hold the vehicles oil capacity) 3 remove the plug on the bottom of the oil pan to allow oil to drain 4 use an oil filter wrench to loosen the oil filter (it will contain oil as well) 5 allow several minutes for oil to drain, the longer the better 6 replace the plug 7 pour some oil into the new filter, and oil the rubber gasket on the new filter 8 replace the filter by hand (do not use filter wrench to tighten) 9 tighten the new filter by hand to one full turn after the gasket touches the engine and no tighter 10 refill from the top of the engine to vehicles oil capacity with recommende weigth of oil note. the engines capacity and the engines capacity with filter differ for the filter will hold oil as well 11 lower the vehicle from jack stands change every 3000 miles when driving in town change every 5000 miles when driving on highway

Jan 09, 2010 | 2009 Toyota Camry

1 Answer

Crankcase Capacity


If it is a factory car pan 5qts,
Drain pan, add 5qts, run 5min check oil.


http://www.sansaworldmp3.com/
http://www.sansaworld.com/

Aug 16, 2008 | 1984 Ford Mustang

Not finding what you are looking for?
2002 Chrysler Voyager Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...