Question about 1991 Mitsubishi Montero

1 Answer

My blinkers dont blink.got new lights, new fuses, and new flasher fuse

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Not sure if this has been answered but the if you look under the drivers side you will see a flasher unit bolted to the side. It looks like a grey box with a V shaped wiring harness attached to it. Jiggle it. It may fix it. It is most likely your problem.

Posted on Sep 19, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 jeep wrangler 2.5


dont break the brakes..... TURNS & HAZ
many blinker, modules , internally flash with any load.
1: check all fuses first... (SOP)
2: then remove the blinker loads from the timer.

see it here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see WIRING, (end)
8w-51/52
chapter 8w, page 51-4 shows the switch. (complex it is)
note how brake and turns are shared, resources. (blub elements)
now 8w-52-6
see the flasher module.
see C305 pin 2, any load on that pin will cause it to flash.(inside)
that would be any switch in the combo switch stuck on.

Apr 07, 2014 | 1997 Jeep Tj

1 Answer

Turn signals blin continually


There is only a few things that can cause blinkers to blink continually, meaning if your saying they wont shut off, Normally it is the blinker flasher or a fuse. Sometimes it can be in the blinker switch itself. I first would check the flasher, and turn signl fuse. If the blinker stays on and does not flash, still can be bad flasher or fuse or a ground problem, You would then have to check the wires around area where there contact to the tail light blinkers and front blinkers. But first start as said earlier with checking flasher fuse, switch and fuse. Mike

Jan 16, 2012 | 1995 Cadillac DeVille

2 Answers

Turn signals(blinkers) turn on but they dont blink?


Flasher module is burnt , just replace it.. you will find it in the fuse panel.

Jul 30, 2010 | 1991 Chevrolet S-10 Blazer

2 Answers

Help I don't know how to change a fuse for my blinkers..


Flasher you should find an round flasher in your fuse box. btn-view-details.png --> Application:
With 2 terminals
Notes: ( Autozone has this part # LL552)
Electronic
-->

Jun 04, 2010 | 1987 Jeep Cherokee

3 Answers

Turn signals dont blink.


You need to replace the turn signal flasher, it's a cylinder shape and may be silver or gold in color. When it goes bad, the turn signals stop flashing. Good luck and keep me posted.

Feb 16, 2010 | 1994 Chevrolet S-10 Blazer

2 Answers

MY HAZARD LIGHTS WORK BUT MY BLINKERS DONT


Try checking the fuse for the blinkers, if it's intact then you'll need changing the blinker switch arms on the steering wheel. Good Luck

Feb 08, 2010 | 2002 Ford F150 Regular Cab

1 Answer

TURN SIGNAL, BRAKE & HAZARD LIGHTS


No Turn Signal Operation (blinker)The turn signal lights in your car are a basic electrical system that controls the front and rear blinker lights to alert the intended direction of the vehicle. We have listed some of the most common problems and repair troubleshooting tips below:
Troubleshooting Procedure
To start troubleshooting this problem:
  • Turn the key to the on position (do not start engine)
  • Inspect the system fuse located in the fuse panel and replace if needed. If you cannot find the location of the blinker fuse consult your owner's manual or an online repair manual
  • When a blinker flasher fails it can cause blinker lights to say on, not blink, or not go on at all. To test the blinker system flasher, remove the flasher unit and insert a jumper wire between the two terminals. If blinker stays on in both directions without blinking, replace the flasher. If you cannot find the location of the blinker flasher consult your owners manual or an online repair manual.
  • 1b7f814.jpg

Jul 09, 2009 | 1999 GMC Denali

4 Answers

Blinkers wont turn on its not the bulbs or fuses 01 tahoe


Did you replace the hazard/flasher/blinker relays?- they are in the fuse block usually.

This is weird, but try this: Turn on your hazard lamps and turn your steering wheel all the way left and all the way right.
Then turn on your left blinker and hold the blinker on while you turn all the way left, then right. It will click and try to turn it off but keep it held down and turned on. Then do the right blinker the same way.
I have had this problem with every GM I've ever had, something about the detent-return and the blinker relays getting reset. I'm not sure why it works, but if your flasher relays are good and your fuses,bulbs and wires are good then this is probably what will fix ya. I've had this happen often enough that I always do this first. My GM vehicles were/are all 60s to 90s models- old school, but try this before you do anything else with it it's free and only takes about 15 seconds to do. Sometimes I have to do it more than once, but eventually the detents reset and they work. Viola!
Good luck and please rate this solution if it fixes ya!

Jun 21, 2009 | 2001 Chevrolet Tahoe

3 Answers

Blinker stopped working, but the hazard lights still work - I think it's a blown fuse but how and where do I fix the fuse


There is 2 different flashers. One flasher for the turn signals and one flasher for the hazards. If you turn on the turn signals and the turn indicator on the dash lights up but doesn't blink, then most likely it is the turn signal flasher that is bad. Good luck.

May 29, 2009 | 1998 Chrysler Sebring

1 Answer

Have 2001 Cherokee, for some time the blinker will turn on but not blink. If you moved blinker handle up and down they would work, Now it wont work at all. Dont know how to find fuse


likely your flasher unit was failing or you had a bulb out somewhere. Flasher should be on right side of steering column under dash yours could be a "combination flasher" Older models had flashers on fuse box under dash on left side.

Mar 10, 2009 | 2001 Jeep Cherokee

Not finding what you are looking for?
1991 Mitsubishi Montero Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...