Question about 1992 Ford Escort 4 Door

1 Answer

Timing belt Hi my nephew just bought a 1992 Ford Escort GT 1.8LT and it needs a new timing belt what is the timing ratio marks supposed to be set at? I hope I'm saying this right (I am his Aunt) he doesn't have access to a computer. Thanks, Teresa tessee47@yahoo.com

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

If you have a local Auto Zone they can give you that information right over the phone at no cost.

Posted on May 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is ford escort timing marks position


I assume timing belt and that you have the Ford engine not the Mazda 1.8L used in tghe GT
. disconnect negative side of the battery
2. place cylinder no.1 TDC compression stoke
3. remove drive belt and tensioner
4. remove timing belt cover
5. raise and support car
6. remove right front tire and splash shield
7. remove crankshaft pulley
8. align timing marks
9. loosen timing belt tensioner
10. remove timing belt
water pump should be check and replaced too

11_4_2012_6_19_59_pm.jpg

11_4_2012_6_20_27_pm.jpg

Nov 04, 2012 | Cars & Trucks

1 Answer

2003 ford escort zx2 out of timing need marks and diagrams to set


Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools. Special tools are required to set the timing

Aug 26, 2011 | 2003 Ford Escort

1 Answer

Timing marks 2000 ford escort


Hi!!

Here are 3 diagrams that correspond to the 3 engines types available for your vehicle.


0996b43f80208cbd.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Be sure that the intake and exhaust camshaft timing marks align so that they face each other-Ford 2.0L (VIN A) engines

2.0L (VIN P) Engines


0996b43f8022f40e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Align the timing marks before removing or installing the timing belt-2.0L (VIN P) SOHC engines



0996b43f80208cbe.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft alignment position-Ford 2.0L DOHC Zetec engines

In case the diagrams don't show, click the following link http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Engine+Mechanical+Components&partName=Engine+Mechanical&pageId=0996b43f802e7310&subChapterTitle=Timing+Belt&partId=0996b43f802e7275#hd1-1-3

Don't forget to rate this answer, GOOD LUCK

Apr 17, 2010 | 2000 Ford Escort

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

1 Answer

How do I set the timing when replacing the timing belt.


If you are just replacing the belt because it's worn. Carefully remove the old belt and replace. no timing will be neccesary

Mar 16, 2009 | 1997 Ford Escort

1 Answer

Timing Belts


Here is a diagram of you timing marks. contact if you need more help. Good Luck and thanks for using FIX YA. http://www.2carpros.com/car_repair_information/tec_info/1991/ford/escort/1991_ford_escort_timing_belt_diagram_marks.htm

Jan 09, 2009 | 1991 Ford Escort

1 Answer

2.0 L Timing Belt Marks


hi if its a twin cam ford engine you wont find marks on the cam pulleys.what you have to do is take off the cam cover and look at the back of the cams you will see slots in them ,what you have to do is you can buy the timing kit for the engine at the main dealers or you can make you own using a flat piece of metal 5mm thick and100 mm long this fits into the two slots at the rear of the cams to lick them in place and th crankshaft pulley mark should be in line also.best of luck.

Sep 30, 2008 | 1999 Ford Escort

1 Answer

Setting timing marks on a 1998 Ford Escort


think u need a tool it locks the engine at top dead centre then u line cams up

Jul 13, 2008 | 1998 Ford Escort

3 Answers

Timing Belt Replacement+Diagram


No it will NOT bend valves on this particular engine, if it goes out of time. I would replace BOTH the timing belt and the drive belt at the same time, since both are very inexpensive, even from the Ford dealer. Line up both timing marks on both the cam and crank sprockets in the 12 o'clock position. The marks are very easy to see, once you remove the timing belt cover. Hope this helps.

Jun 22, 2008 | 1991 Ford Escort

Not finding what you are looking for?
1992 Ford Escort 4 Door Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...