Question about 2010 Chevrolet Camaro

1 Answer

Yes, the horn cover removal method - 2010 Chevrolet Camaro

Posted by on

  • 2 more comments 
  • captainjackf Sep 12, 2010

    I Pulled up on it as hard as I daired and it would not come off. Steve

  • captainjackf Sep 12, 2010

    That wouldn't work I applied a grate deal of pull to try to take it of and it would not release. this one must have tabs or something like that.

  • captainjackf Sep 21, 2010

    Hi, it took me a while to get vto my dealer in the area, it is a good thing I did, in the future it would be best if you didn't give advice if you are only gessing, and CHARGE SOME ******
    LIKE ME FOR YOUR BAD ADVICE, The steering wheel hase 2 acess holes underneath and you have to use a long thin dull tool aboute 3/16 of an inch in diameter to depress a spring bar on each side of the horn button to release it to come off, if I

  • captainjackf Sep 22, 2010

    They MIGHT have changed, FIRST you give me bad advice, then you talk as if I don't know what I am talking about, If I had done what YOU, told me, It would have cost me BIGTIME. If you aren't sure uou shouldn't offer advice.Steve S.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,515 Answers

Hi,

You just need to pull up and it would come off.

Note - I am taking into consideration you wanted to remove the center horn button / pad / bar.

If it's the comfort grip steering wheel just pull it up from underneath using your middle finger and ring finger which is pretty much what i explained above.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Sep 12, 2010

  • 1 more comment 
  • taran_2005
    taran_2005 Sep 12, 2010

    Thanks for your response!!

    Just pull the horn button off and there is a clip to pry off and then remove the nut.If that does not help, revert and i could try to get the service manual for the same.

    Let me know,if needed further assistance.

    Hope i helped you.

    Thanks for using ' Fixya ' and have a nice day!!

  • taran_2005
    taran_2005 Sep 22, 2010

    Thanks for your response!!

    To begin with, i apologize, however the information i gave to you is what i saw on all the past models. They might have changed for 2010. I appreciate your input. I was unable to get a service manual, so told you what i saw on other models.

    I am sorry that i did not get the answer as per your requirement. Hope you would have a wonderful time.

    Thanks and Regards
    taran_2005

  • taran_2005
    taran_2005 Sep 23, 2010

    Thanks for your response!!

    I got your point, but there are certain situation when the Haynes manual is also not correct. If you worked on many cars, and there is no difference, you would assume that in the new model it would be correct. I am not defending myself, however, 1% error could be there. But, trust me 99% you are on target. I could say, every day is not perfect and it was one of those days when things went wrong. I apologize that my solution didn't helped you.

    Hope to hear from you soon.

    Thanks and Regards
    taran_2005

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get access to the horn for replacement?


if dead , you cant find it by listening, right....
can you see it? did you look at all angles possible to see it?
under hood, and behind that grill. (its there find it)
if yes, then you know what needs to be removed. (a deductive least path of resistance and tools)
the FSM covers this.
or alldata.com (search horn) remove.

just 4 bucks to read and learn all steps of things.

https://suzukipitstopplus.com/Products/1066-2006-forenza-reno-service-manual.aspx

EF 16 fuse blown
if you remove the horn relay
and hot wire the 87 relay pin socket with 12vdc (use inline 15amp fuse jumper line (per FSM rules or ASE rules... same...)
then the horn must honk.!
if not the horn base may be just rusty. clean it,
or bench test it, first.


if behind the grill and there are no panels that come off to get at it or not get to it from underneath car, then the grill needs to come out, some are in the engine bay, front corners.. look there yet.?
google work>?
Best Answer: it located in front of the bumper cover...

my online books do not cover horn. so.... pay 4 bucks. above.
my last answer was this.

http://www.fixya.com/cars/t25588791-2006_suzuki_forenza_horn_will_not_blow

and horns can short. as can its wire.
so if the hot wire blows the (tech, fused jumper)
then that path is shorted.
find your horn, then take a photo of it. and post it?
and we can advise how to reach it.
i can name 10 locations of horns , on cars.
but not this one, its a Daewoo, suzuki wonder box with GM parts stuffed in....

ok, my forenza folder has full set of harnesses
and bingo
here is your horn, seem front grill out to me
but youd need to see exactly how its mounted

eaeee2b7-f91e-4860-a4e3-e675ee305bc9.jpg

Sep 09, 2015 | 2006 Suzuki Forenza

Tip

Drivers airbag removal / horn switch removal 1998 dodge neon


I have a 98 dodge neon and the horn was stuck on all the time. I could not find anyone who could tell me how to remove the cover on the airbag so I could get to the horn touchpad. this is what i did.
first unhook the battery.
remove the 2 screws on the cruise control buttons on each side of the steering wheel.
remove the bolt(s) from both sides of the airbag bracket
unplug the horn wire
unplug the airbag wire CAREFULLY (it's the one in the center).( I left this hooked up)
I did not need to completely remove the air bag from my car, because my horn was stuck on and I just needed to remove the cover.
after I removed the airbag assembly I removed all the screws holding the cover on I removed the inner touch pad so I could fix it.
I reversed the steps to put it back together.. the horn works as it should.

on Jul 26, 2015 | 1998 Dodge Neon

1 Answer

Horn is stuck on 2004 chevy malibu


There is one wire that attaches diirectly to horn that can be removed to stop horn. There is a fuse in fusebox that may also be removed. There are screws in the backside of steering wheel to remove front of steering wheel cover and inspect horn contact for damage or corrosion. If removing steering cover, use care to disconnect airbag actuator to prevent airbag inflation.

Nov 13, 2013 | 2004 Chevrolet Malibu

1 Answer

Horn blows by itself


I verify its not a stuck relay...

I disconnect connector under dash and horn stops...


I then suspect its the Horn contacts or a worn grounded wire in air bag/horn switch assembly in steering wheel.




The decorative Vinyl cover shrinks with age...presses on horn contacts against air bag.

I Disconnect Air bag connector (identified as Yellow wire and Connector) usually under dash.

WARNING: ( I Do not - I DO NoT probe the yellow harness/connector with a meter or test light. A test light WILL Detonate my air bag, and impale the bracket in a nearby object/person - me.)

I Removed screws (2) behind steering wheel - which allow air bag horn assembly to be removed.


I Disconnect Air bag connector in this location as well (identified as Yellow wire and Connector) and then;




The red (color varies) and black Horn wires will be plugged into ribbon connectors usually (2) two that feed/connect to contacts for horn function on face of air bag.

I pause here and verify horn will stop blowing when I disconnect the wires going to horn contacts. So I get horn blowing again...

Check horn: To verify this is the cause; I reconnect (whatever fuse/relay/ connector (Not the airbag connector) I disconnected so they will stop blowing) and get horn/s so they are blowing again...

Then I disconnect the ribbon connectors to verify blowing stops.

Note: The experience I had with horn on

Buick Park Ave was at night when temperature cools after hot day, the vinyl cover shrank and horn blows... pressing on horn area of steering wheel firmly would stop horn briefly - then continue.

Note: I will need a rivet tool and rivets... to reassemble.

WARNING: I Do not drill into airbag explosive container. If I do not know how to carefully drill off correct rivet heads and remove vinyl decorative cover from air bag/horn... I STOP and go to the junkyard or ebay and purchase/replace the airbag/horn assembly.

I continued by drilling out rivets (the rivets holding vinyl cover) by using a drill bit as large (or smaller) as the head of rivet and drill gently to release head from rivet body/shank.



I mark all pieces with a magic marker to verify I reassemble right side up (all metal brackets and trim plates and cover).



I Remove vinyl cover exposing horn contact pads which were sandwiched between cover and air bag container.

I used a razor blade to remove vinyl honeycomb material from area of vinyl cover - that when pressed - would activate horn/contacts.

Only a 1/16 of an inch or less needs to be removed.

(I Bend cover inside out and shave material off of area slowly. Care not to cut myself.)

I Reassemble in reverse order with rivets.

Check horn: ...function at this point... by plugging in horn connectors and assure horn contacts work properly as expected.





Feb 21, 2013 | 1997 Oldsmobile 88

1 Answer

My question on my 94 toyota pickup 2wd; how can I check to see if the horn contacts are making contact? since the horn contacts are located under the steering wheel, and the air bag is also located there,...


disconnect the negative batery terminal be fore you mess with the horn. the cover should come off easily and you will the wire for the horn on my car the wire is green

Sep 21, 2011 | Toyota Pickup Cars & Trucks

2 Answers

The horn on my 1997 chevy cavalier went out


Un plug horn connect horn to another 12 volt power source, if it works then the problem is the horn button located in the steering wheel assembley

Sep 09, 2011 | 1997 Chevrolet Cavalier

1 Answer

98 Cavalier, Horn went on, I had to disconnect the horn itself to stopthe noise. Problem in the steering wheel hub?? Bad Horn switch?? is a new switch available??


Yes, the problem will probably be a sticking switch. When you remove the steering wheel cover you should be able to see the switch(s). I think your vehicle has two and usually spraying them with an electronic cleaning fluid does the trick.

Apr 01, 2011 | 1998 Chevrolet Cavalier

1 Answer

Do I have to replace the whole turn signal switch or can I get just the hazard warning button


To buy it aftermarket yes you'll need the entire multi-function switch. However that year had a recall for just the hazard button in the switch, and can be purchased separately at a GM dealership. They lock in at the sides, remove upper steering wheel cover (hint you may want to remove the horn fuse or relay first, it can be activated while installing), use a very small slotted screwdriver and lightly pry the sides outwards. Pull the hazard button straight up. Apply lube to new button, and push down into groove until it locks. Reassemble the cover and horn fuse.

Feb 17, 2011 | 1997 Chevrolet Astro

1 Answer

Horn not working. Fuse is good. 2005 Jeep Wrangler. How do you remove the rubber cover on the sterring wheel to get at the horn.


May be bad horn. Get a 12 volt test light or multi-meter and attach to the horn wire at the horn. Have a helper press the horn. If you have 12 volts when it is pressed, horn itself is bad. Otherwise, may be bad horn relay. Horn cover should pull off.

Dec 31, 2009 | 2005 Jeep Wrangler

1 Answer

Horn on 1984 camaro is not working correctly.


it turns on on certain position of the steering wheel? if yes, then the problem is clock spring under the horn pad. you need to change it if it is electronics.

Apr 26, 2009 | 1984 Chevrolet Camaro

Not finding what you are looking for?
2010 Chevrolet Camaro Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...